fixing iso 14443b (issue #103):

[proxmark3-svn] / fpga / hi_read_rx_xcorr.v

//-----------------------------------------------------------------------------
//
// Jonathan Westhues, April 2006
//-----------------------------------------------------------------------------

module hi_read_rx_xcorr(
    pck0, ck_1356meg, ck_1356megb,
    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
    adc_d, adc_clk,
    ssp_frame, ssp_din, ssp_dout, ssp_clk,
    cross_hi, cross_lo,
    dbg,
    snoop
);
    input pck0, ck_1356meg, ck_1356megb;
    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
    input [7:0] adc_d;
    output adc_clk;
    input ssp_dout;
    output ssp_frame, ssp_din, ssp_clk;
    input cross_hi, cross_lo;
    output dbg;
    input snoop;

// Carrier is steady on through this, unless we're snooping.
assign pwr_hi = ck_1356megb & (~snoop);
assign pwr_oe1 = 1'b0;
assign pwr_oe3 = 1'b0;
assign pwr_oe4 = 1'b0;

wire adc_clk = ck_1356megb;

// When we're a reader, we just need to do the BPSK demod; but when we're an
// eavesdropper, we also need to pick out the commands sent by the reader,
// using AM. Do this the same way that we do it for the simulated tag.
reg after_hysteresis, after_hysteresis_prev, after_hysteresis_prev_prev;
reg [11:0] has_been_low_for;
always @(negedge adc_clk)
begin
    if(& adc_d[7:0]) after_hysteresis <= 1'b1;
    else if(~(| adc_d[7:0])) after_hysteresis <= 1'b0;

    if(after_hysteresis)
    begin
        has_been_low_for <= 7'b0;
    end
    else
    begin
        if(has_been_low_for == 12'd4095)
        begin
            has_been_low_for <= 12'd0;
            after_hysteresis <= 1'b1;
        end
        else
            has_been_low_for <= has_been_low_for + 1;
    end
end

// Let us report a correlation every 4 subcarrier cycles, or 4*16 samples,
// so we need a 6-bit counter.
reg [5:0] corr_i_cnt;
// And a couple of registers in which to accumulate the correlations.
// we would add at most 32 times adc_d, the result can be held in 13 bits. 
// Need one additional bit because it can be negative as well
reg signed [13:0] corr_i_accum;
reg signed [13:0] corr_q_accum;
reg signed [7:0] corr_i_out;
reg signed [7:0] corr_q_out;
// clock and frame signal for communication to ARM
reg ssp_clk;
reg ssp_frame;



// ADC data appears on the rising edge, so sample it on the falling edge
always @(negedge adc_clk)
begin
    corr_i_cnt <= corr_i_cnt + 1;

    // These are the correlators: we correlate against in-phase and quadrature
    // versions of our reference signal, and keep the (signed) result to
    // send out later over the SSP.
    if(corr_i_cnt == 7'd0)
    begin
        if(snoop)
        begin
			// 7 most significant bits of tag signal (signed), 1 bit reader signal:
            corr_i_out <= {corr_i_accum[13:7], after_hysteresis_prev_prev};
            corr_q_out <= {corr_q_accum[13:7], after_hysteresis_prev};
			after_hysteresis_prev_prev <= after_hysteresis;
        end
        else
        begin
            // 8 most significant bits of tag signal
            corr_i_out <= corr_i_accum[13:6];
            corr_q_out <= corr_q_accum[13:6];
        end

        corr_i_accum <= adc_d;
        corr_q_accum <= adc_d;
    end
    else
    begin
        if(corr_i_cnt[3])
            corr_i_accum <= corr_i_accum - adc_d;
        else
            corr_i_accum <= corr_i_accum + adc_d;

        if(corr_i_cnt[3] == corr_i_cnt[2])			// phase shifted by pi/2
            corr_q_accum <= corr_q_accum + adc_d;
        else
            corr_q_accum <= corr_q_accum - adc_d;

    end

    // The logic in hi_simulate.v reports 4 samples per bit. We report two
    // (I, Q) pairs per bit, so we should do 2 samples per pair.
    if(corr_i_cnt == 6'd31)
        after_hysteresis_prev <= after_hysteresis;

    // Then the result from last time is serialized and send out to the ARM.
    // We get one report each cycle, and each report is 16 bits, so the
    // ssp_clk should be the adc_clk divided by 64/16 = 4.

    if(corr_i_cnt[1:0] == 2'b10)
        ssp_clk <= 1'b0;

    if(corr_i_cnt[1:0] == 2'b00)
    begin
        ssp_clk <= 1'b1;
        // Don't shift if we just loaded new data, obviously.
        if(corr_i_cnt != 7'd0)
        begin
            corr_i_out[7:0] <= {corr_i_out[6:0], corr_q_out[7]};
            corr_q_out[7:1] <= corr_q_out[6:0];
        end
    end

	// set ssp_frame signal for corr_i_cnt = 0..3 and corr_i_cnt = 32..35
	// (send two frames with 8 Bits each)
    if(corr_i_cnt[5:2] == 4'b0000 || corr_i_cnt[5:2] == 4'b1000)
        ssp_frame = 1'b1;
    else
        ssp_frame = 1'b0;

end

assign ssp_din = corr_i_out[7];

assign dbg = corr_i_cnt[3];

// Unused.
assign pwr_lo = 1'b0;
assign pwr_oe2 = 1'b0;

endmodule