CHG: remove clang warning for -O4,

[proxmark3-svn] / fpga / fpga_lf.v

//-----------------------------------------------------------------------------
// Jonathan Westhues, March 2006
// iZsh <izsh at fail0verflow.com>, June 2014
//-----------------------------------------------------------------------------

`include "lo_read.v"
`include "lo_passthru.v"
`include "lo_edge_detect.v"
`include "util.v"
`include "clk_divider.v"

module fpga_lf(
	input spck, output miso, input mosi, input ncs,
	input pck0, input ck_1356meg, input ck_1356megb,
	output pwr_lo, output pwr_hi,
	output pwr_oe1, output pwr_oe2, output pwr_oe3, output pwr_oe4,
	input [7:0] adc_d, output adc_clk, output adc_noe,
	output ssp_frame, output ssp_din, input ssp_dout, output ssp_clk,
	input cross_hi, input cross_lo,
	output dbg
);

//-----------------------------------------------------------------------------
// The SPI receiver. This sets up the configuration word, which the rest of
// the logic looks at to determine how to connect the A/D and the coil
// drivers (i.e., which section gets it). Also assign some symbolic names
// to the configuration bits, for use below.
//-----------------------------------------------------------------------------

reg [15:0] shift_reg;
reg [7:0] divisor;
reg [7:0] conf_word;
reg [7:0] user_byte1;

always @(posedge ncs)
begin
	case(shift_reg[15:12])
		4'b0001:
			begin
				conf_word <= shift_reg[7:0];
				if (shift_reg[7:0] == 8'b00000001) begin // LF edge detect
					user_byte1 <= 127; // default threshold
				end
			end
		4'b0010: divisor <= shift_reg[7:0];			// FPGA_CMD_SET_DIVISOR
		4'b0011: user_byte1 <= shift_reg[7:0];		// FPGA_CMD_SET_USER_BYTE1
	endcase
end

always @(posedge spck)
begin
	if(~ncs)
	begin
		shift_reg[15:1] <= shift_reg[14:0];
		shift_reg[0] <= mosi;
	end
end

wire [2:0] major_mode = conf_word[7:5];

// For the low-frequency configuration:
wire lf_field = conf_word[0];
wire lf_ed_toggle_mode = conf_word[1]; // for lo_edge_detect
wire [7:0] lf_ed_threshold = user_byte1;

//-----------------------------------------------------------------------------
// And then we instantiate the modules corresponding to each of the FPGA's
// major modes, and use muxes to connect the outputs of the active mode to
// the output pins.
//-----------------------------------------------------------------------------
wire [7:0] pck_cnt;
wire pck_divclk;
clk_divider div_clk(pck0, divisor, pck_cnt, pck_divclk);

lo_read lr(
	pck0, pck_cnt, pck_divclk,
	lr_pwr_lo, lr_pwr_hi, lr_pwr_oe1, lr_pwr_oe2, lr_pwr_oe3, lr_pwr_oe4,
	adc_d, lr_adc_clk,
	lr_ssp_frame, lr_ssp_din, lr_ssp_clk,
	lr_dbg, lf_field
);

lo_passthru lp(
	pck_divclk,
	lp_pwr_lo, lp_pwr_hi, lp_pwr_oe1, lp_pwr_oe2, lp_pwr_oe3, lp_pwr_oe4,
	lp_adc_clk,
	lp_ssp_din, ssp_dout,
	cross_lo,
	lp_dbg
);

lo_edge_detect le(
	pck0, pck_divclk,
	le_pwr_lo, le_pwr_hi, le_pwr_oe1, le_pwr_oe2, le_pwr_oe3, le_pwr_oe4,
	adc_d, le_adc_clk,
	le_ssp_frame, ssp_dout, le_ssp_clk,
	cross_lo,
	le_dbg,
	lf_field,
	lf_ed_toggle_mode, lf_ed_threshold
);

// Major modes:
//   000 --  LF reader (generic)
//   001 --  LF edge detect (generic)
//   010 --  LF passthrough

mux8 mux_ssp_clk		(major_mode, ssp_clk,   lr_ssp_clk,   le_ssp_clk,         1'b0,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0);
mux8 mux_ssp_din		(major_mode, ssp_din,   lr_ssp_din,         1'b0,   lp_ssp_din,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0);
mux8 mux_ssp_frame		(major_mode, ssp_frame, lr_ssp_frame, le_ssp_frame,       1'b0,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0); 
mux8 mux_pwr_oe1		(major_mode, pwr_oe1,   lr_pwr_oe1,   le_pwr_oe1,   lp_pwr_oe1,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0);
mux8 mux_pwr_oe2		(major_mode, pwr_oe2,   lr_pwr_oe2,   le_pwr_oe2,   lp_pwr_oe2,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0); 
mux8 mux_pwr_oe3		(major_mode, pwr_oe3,   lr_pwr_oe3,   le_pwr_oe3,   lp_pwr_oe3,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0);
mux8 mux_pwr_oe4		(major_mode, pwr_oe4,   lr_pwr_oe4,   le_pwr_oe4,   lp_pwr_oe4,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0); 
mux8 mux_pwr_lo			(major_mode, pwr_lo,    lr_pwr_lo,    le_pwr_lo,    lp_pwr_lo,    1'b0, 1'b0, 1'b0, 1'b0, 1'b0); 
mux8 mux_pwr_hi			(major_mode, pwr_hi,    lr_pwr_hi,    le_pwr_hi,    lp_pwr_hi,    1'b0, 1'b0, 1'b0, 1'b0, 1'b0); 
mux8 mux_adc_clk		(major_mode, adc_clk,   lr_adc_clk,   le_adc_clk,   lp_adc_clk,   1'b0, 1'b0, 1'b0, 1'b0, 1'b0); 
mux8 mux_dbg			(major_mode, dbg,       lr_dbg,       le_dbg,       lp_dbg,       1'b0, 1'b0, 1'b0, 1'b0, 1'b0); 

// In all modes, let the ADC's outputs be enabled.
assign adc_noe = 1'b0;

endmodule