cvs.zerfleddert.de Git - proxmark3-svn/blob - fpga/hi_simulate.v

   1 //-----------------------------------------------------------------------------
   2 // Pretend to be an ISO 14443 tag. We will do this by alternately short-
   3 // circuiting and open-circuiting the antenna coil, with the tri-state
   4 // pins.
   5 //
   6 // We communicate over the SSP, as a bitstream (i.e., might as well be
   7 // unframed, though we still generate the word sync signal). The output
   8 // (ARM -> FPGA) tells us whether to modulate or not. The input (FPGA
   9 // -> ARM) is us using the A/D as a fancy comparator; this is with
  10 // (software-added) hysteresis, to undo the high-pass filter.
  11 //
  12 // At this point only Type A is implemented. This means that we are using a
  13 // bit rate of 106 kbit/s, or fc/128. Oversample by 4, which ought to make
  14 // things practical for the ARM (fc/32, 423.8 kbits/s, ~50 kbytes/s)
  15 //
  16 // Jonathan Westhues, October 2006
  17 //-----------------------------------------------------------------------------
  18
  19 module hi_simulate(
  20     ck_1356meg,
  21     pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
  22     adc_d, adc_clk,
  23     ssp_frame, ssp_din, ssp_dout, ssp_clk,
  24     dbg,
  25     mod_type
  26 );
  27     input ck_1356meg;
  28     output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
  29     input [7:0] adc_d;
  30     output adc_clk;
  31     input ssp_dout;
  32     output ssp_frame, ssp_din, ssp_clk;
  33     output dbg;
  34     input [2:0] mod_type;
  35
  36
  37 // The comparator with hysteresis on the output from the peak detector.
  38 reg after_hysteresis;
  39 assign adc_clk = ck_1356meg;
  40
  41 always @(negedge adc_clk)
  42 begin
  43     if(& adc_d[7:5]) after_hysteresis = 1'b1;           // if (adc_d >= 224)
  44     else if(~(| adc_d[7:5])) after_hysteresis = 1'b0;   // if (adc_d <= 31)
  45 end
  46
  47
  48 // Divide 13.56 MHz to produce various frequencies for SSP_CLK
  49 // and modulation.
  50 reg [8:0] ssp_clk_divider;
  51
  52 always @(negedge adc_clk)
  53     ssp_clk_divider <= (ssp_clk_divider + 1);
  54
  55 reg ssp_clk;
  56
  57 always @(negedge adc_clk)
  58 begin
  59     if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_424K_8BIT)
  60       // Get bit every at 53KHz (every 8th carrier bit of 424kHz)
  61       ssp_clk <= ~ssp_clk_divider[7];
  62     else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_212K)
  63       // Get next bit at 212kHz
  64       ssp_clk <= ~ssp_clk_divider[5];
  65     else
  66       // Get next bit at 424Khz
  67       ssp_clk <= ~ssp_clk_divider[4];
  68 end
  69
  70
  71 // Produce the byte framing signal; the phase of this signal
  72 // is arbitrary, because it's just a bit stream in this module.
  73 reg ssp_frame;
  74 always @(negedge adc_clk)
  75 begin
  76         if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_212K)
  77         begin
  78                 if (ssp_clk_divider[8:5] == 4'd1)
  79                         ssp_frame <= 1'b1;
  80                 if (ssp_clk_divider[8:5] == 4'd5)
  81                         ssp_frame <= 1'b0;
  82         end
  83         else
  84         begin
  85                 if (ssp_clk_divider[7:4] == 4'd1)
  86                         ssp_frame <= 1'b1;
  87                 if (ssp_clk_divider[7:4] == 4'd5)
  88                         ssp_frame <= 1'b0;
  89         end
  90 end
  91
  92
  93 // Synchronize up the after-hysteresis signal, to produce DIN.
  94 reg ssp_din;
  95 always @(posedge ssp_clk)
  96     ssp_din = after_hysteresis;
  97
  98 // Modulating carrier frequency is fc/64 (212kHz) to fc/16 (848kHz). Reuse ssp_clk divider for that.
  99 reg modulating_carrier;
 100 always @(*)
 101     if (mod_type == `FPGA_HF_SIMULATOR_NO_MODULATION)
 102         modulating_carrier <= 1'b0;                          // no modulation
 103     else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_BPSK)
 104         modulating_carrier <= ssp_dout ^ ssp_clk_divider[3]; // XOR means BPSK
 105     else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_212K)
 106         modulating_carrier <= ssp_dout & ssp_clk_divider[5]; // switch 212kHz subcarrier on/off
 107     else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_424K || mod_type == `FPGA_HF_SIMULATOR_MODULATE_424K_8BIT)
 108         modulating_carrier <= ssp_dout & ssp_clk_divider[4]; // switch 424kHz modulation on/off
 109     else
 110         modulating_carrier <= 1'b0;                           // yet unused
 111
 112
 113 // Load modulation. Toggle only one of these, since we are already producing much deeper
 114 // modulation than a real tag would.
 115 assign pwr_hi = 1'b0;                   // HF antenna connected to GND
 116 assign pwr_oe3 = 1'b0;                  // 10k Load
 117 assign pwr_oe1 = modulating_carrier;    // 33 Ohms Load
 118 assign pwr_oe4 = modulating_carrier;    // 33 Ohms Load
 119
 120 // This is all LF and doesn't matter
 121 assign pwr_lo = 1'b0;
 122 assign pwr_oe2 = 1'b0;
 123
 124
 125 assign dbg = ssp_frame;
 126
 127 endmodule