+/* Send a frame in reader mode, the FPGA must have been set up by
+ * LegicRfReader
+ */
+static void frame_send_rwd(uint16_t data, int bits)
+{
+ /* Start clock */
+ timer->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ while(timer->TC_CV > 1) ; /* Wait till the clock has reset */
+
+ int i;
+ for(i=0; i<bits; i++) {
+ int starttime = timer->TC_CV;
+ int pause_end = starttime + RWD_TIME_PAUSE, bit_end;
+ int bit = data & 1;
+ data = data >> 1;
+
+ if(bit) {
+ bit_end = starttime + RWD_TIME_1;
+ } else {
+ bit_end = starttime + RWD_TIME_0;
+ }
+
+ /* RWD_TIME_PAUSE time off, then some time on, so that the complete bit time is
+ * RWD_TIME_x, where x is the bit to be transmitted */
+ AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
+ while(timer->TC_CV < pause_end) ;
+ AT91C_BASE_PIOA->PIO_SODR = GPIO_SSC_DOUT;
+ while(timer->TC_CV < bit_end) ;
+ }
+
+ {
+ /* One final pause to mark the end of the frame */
+ int pause_end = timer->TC_CV + RWD_TIME_PAUSE;
+ AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
+ while(timer->TC_CV < pause_end) ;
+ AT91C_BASE_PIOA->PIO_SODR = GPIO_SSC_DOUT;
+ }
+
+ /* Reset the timer, to measure time until the start of the tag frame */
+ timer->TC_CCR = AT91C_TC_SWTRG;
+}
+
+/* Receive a frame from the card in reader emulation mode, the FPGA and
+ * timer must have been set up by LegicRfReader and frame_send_rwd.
+ *
+ * The LEGIC RF protocol from card to reader does not include explicit
+ * frame start/stop information or length information. The reader must
+ * know beforehand how many bits it wants to receive. (Notably: a card
+ * sending a stream of 0-bits is indistinguishable from no card present.)
+ *
+ * Receive methodology: There is a fancy correlator in hi_read_rx_xcorr, but
+ * I'm not smart enough to use it. Instead I have patched hi_read_tx to output
+ * the ADC signal with hysteresis on SSP_DIN. Bit-bang that signal and look
+ * for edges. Count the edges in each bit interval. If they are approximately
+ * 0 this was a 0-bit, if they are approximately equal to the number of edges
+ * expected for a 212kHz subcarrier, this was a 1-bit. For timing we use the
+ * timer that's still running from frame_send_rwd in order to get a synchronization
+ * with the frame that we just sent.
+ *
+ * FIXME: Because we're relying on the hysteresis to just do the right thing
+ * the range is severely reduced (and you'll probably also need a good antenna).
+ * So this should be fixed some time in the future for a proper receiver.
+ */
+static void frame_receive_rwd(struct legic_frame * const f, int bits)
+{
+ uint16_t the_bit = 1; /* Use a bitmask to save on shifts */
+ uint16_t data=0;
+ int i, old_level=0, edges=0;
+ int next_bit_at = TAG_TIME_WAIT;
+
+
+ if(bits > 16)
+ bits = 16;
+
+ AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_DIN;
+ AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DIN;
+
+ while(timer->TC_CV < next_bit_at) ;
+ next_bit_at += TAG_TIME_BIT;
+
+ for(i=0; i<bits; i++) {
+ edges = 0;
+ while(timer->TC_CV < next_bit_at) {
+ int level = (AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_DIN);
+ if(level != old_level)
+ edges++;
+ old_level = level;
+ }
+ next_bit_at += TAG_TIME_BIT;
+
+ if(edges > 20 && edges < 60) { /* expected are 42 edges */
+ data |= the_bit;
+ }
+
+
+ the_bit <<= 1;
+ }
+
+ f->data = data;
+ f->bits = bits;
+}
+
+/* Figure out a response to a frame in tag mode */
+static void frame_respond_tag(struct legic_frame const * const f)
projects / proxmark3-svn / blobdiff