NOTICE:
-(2014-03-17)
-Moving the repository from google code to GitHub is up for discussion!
-Please check out the following thread and post your comments...
-http://www.proxmark.org/forum/viewtopic.php?id=1902
-Discussions will close on March 31st.
+(2014-03-26)
+This is now the official Proxmark repository!
-INTRO:
+INTRODUCTION:
-This file contains enough software, logic (for the FPGA), and design
-documentation for the hardware that you could, at least in theory,
-do something useful with a proxmark3. It has commands to:
-
- * read any kind of 125 kHz unidirectional tag
- * simulate any kind of 125 kHz unidirectional tag
-
-(This is enough to perform all of the silly cloning attacks, like the
-ones that I did at the Capitol in Sacramento, or anything involving
-a Verichip. From a technical standpoint, these are not that exciting,
-although the `software radio' architecture of the proxmark3 makes it
-easy and fun to support new formats.)
-
-As a bonus, I include some code to use the 13.56 MHz hardware, so you can:
-
- * do anything that a (medium-range) ISO 15693 reader could
- * read an ISO 14443 tag, if you know the higher-layer protocol
- * pretend to be an ISO 14443 tag, if you know the higher-layer protocol
- * snoop on an ISO 14443 transaction
-
-I am not actively developing any of this. I have other projects that
-seem to be more useful.
-
-USING THE PACKAGE:
-
-The software tools required to build include:
-
- * cygwin or other unix-like tools for Windows
- * devkitPro (http://wiki.devkitpro.org/index.php/Getting_Started/devkitARM)
- * Xilinx's WebPack tools
- * Modelsim (for test only)
- * perl
-
-When installing devkitPro, you only need to install the compiler itself. Additional
-support libraries are not required.
-
-Documentation is minimal, but see the doc/ directory for what exists. A
-previous familiarity with the ARM, with digital signal processing,
-and with embedded programming in general is assumed.
-
-The device is used through a specialized command line interface; for
-example, to clone a Verichip, you might type:
-
- loread ; this reads the tag, and stores the
- ; raw samples in memory on the ARM
-
- losamples ; then we download the samples to
- ; the PC
-
- vchdemod clone ; demodulate the ID, and then put it
- ; back in a format that we can replay
-
- losim ; and then replay it
+The proxmark3 is a powerful general purpose RFID tool, the size of a deck
+of cards, designed to snoop, listen and emulate everything from
+Low Frequency (125kHz) to High Frequency (13.56MHz) tags.
-To read an ISO 15693 tag, you might type:
-
- hiread ; read the tag; this involves sending a
- ; particular command, and then getting
- ; the response (which is stored as raw
- ; samples in memory on the ARM)
-
- hisamples ; then download those samples to the PC
-
- hi15demod ; and demod them to bits (and check the
- ; CRC etc. at the same time)
-
-Notice that in both cases the signal processing mostly happened on the PC
-side; that is of course not practical for a real reader, but it is easier
-to initially write your code and debug on the PC side than on the ARM. As
-long as you use integer math (and I do), it's trivial to port it over
-when you're done.
-
-The USB driver and bootloader are documented (and available separately
-for download, if you wish to use them in another project) at
+This repository contains enough software, logic (for the FPGA), and design
+documentation for the hardware that you could, at least in theory,
+do something useful with a proxmark3.
+
+RESOURCES:
+
+ * This repository!
+ https://github.com/Proxmark/proxmark3
+
+ * The Wiki
+ https://github.com/Proxmark/proxmark3/wiki
+
+ * The GitHub page
+ http://proxmark.github.io/proxmark3/
+
+ * The Forum
+ http://www.proxmark.org/forum
+
+ * The IRC chanel
+ irc.freenode.org #proxmark3
+ -or-
+ http://webchat.freenode.net/?channels=#proxmark3
+
+DEVELOPMENT:
+
+The tools required to build or run the project will vary depending on
+your operating system. Please refer to the Wiki for details.
+
+ * https://github.com/Proxmark/proxmark3/wiki
- http://cq.cx/trivia.pl
+OBTAINING HARDWARE:
+The Proxmark 3 is available for purcahse (assembled and tested) from the
+following locations:
-OBTAINING HARDWARE:
+ * http://proxmark3.com/
+ * http://www.xfpga.com/
-Most of the ultra-low-volume contract assemblers that have sprung up
-(Screaming Circuits, the various cheap Asian suppliers, etc.) could put
+Most of the ultra-low-volume contract assemblers could put
something like this together with a reasonable yield. A run of around
a dozen units is probably cost-effective. The BOM includes (possibly-
outdated) component pricing, and everything is available from Digikey
Excellon drill file.
-FUTURE PLANS, ENHANCEMENTS THAT YOU COULD MAKE:
-
-At some point I should write software involving a proper real-time
-operating system for the ARM. I would then provide interrupt-driven
-drivers for many of the peripherals that are polled now (the USB,
-the data stream from the FPGA), which would make it easier to develop
-complex applications.
-
-It would not be all that hard to implement the ISO 15693 reader properly
-(with anticollision, all the commands supported, and so on)--the signal
-processing is already written, so it is all straightforward applications
-work.
-
-I have basic support for ISO 14443 as well: a sniffer, a simulated
-tag, and a reader. It won't do anything useful unless you fill in the
-high-layer protocol.
-
-Nicer (i.e., closer-to-optimal) implementations of all kinds of signal
-processing would be useful as well.
-
-A practical implementation of the learning-the-tag's-ID-from-what-the-
-reader-broadcasts-during-anticollision attacks would be relatively
-straightforward. This would involve some signal processing on the FPGA,
-but not much else after that.
-
-It would be neat to write a driver that could stream samples from the A/Ds
-over USB to the PC, using the full available bandwidth of USB. I am not
-yet sure what that would be good for, but surely something. This would
-require a kernel-mode driver under Windows, though, which is more work.
-
-
LICENSING:
This program is free software; you can redistribute it and/or modify
projects / proxmark3-svn / blobdiff