// Gerhard de Koning Gans, April 2008
//-----------------------------------------------------------------------------
+// constants for the different modes:
+`define SNIFFER 3'b000
+`define TAGSIM_LISTEN 3'b001
+`define TAGSIM_MOD 3'b010
+`define READER_LISTEN 3'b011
+`define READER_MOD 3'b100
+
module hi_iso14443a(
pck0, ck_1356meg, ck_1356megb,
pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
output dbg;
input [2:0] mod_type;
-reg ssp_clk;
-reg ssp_frame;
-reg fc_div_2;
-always @(posedge ck_1356meg)
- fc_div_2 = ~fc_div_2;
+wire adc_clk = ck_1356meg;
+
-wire adc_clk;
-assign adc_clk = ck_1356meg;
-reg after_hysteresis, after_hysteresis_prev1, after_hysteresis_prev2, after_hysteresis_prev3;
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Reader -> PM3:
+// detecting and shaping the reader's signal. Reader will modulate the carrier by 100% (signal is either on or off). Use a
+// hysteresis (Schmitt Trigger) to avoid false triggers during slowly increasing or decreasing carrier amplitudes
+reg after_hysteresis;
reg [11:0] has_been_low_for;
-reg [8:0] saw_deep_modulation;
-reg [2:0] deep_counter;
-reg deep_modulation;
+
always @(negedge adc_clk)
begin
- if(& adc_d[7:6]) after_hysteresis <= 1'b1;
- else if(~(| adc_d[7:4])) after_hysteresis <= 1'b0;
+ if(adc_d >= 16) after_hysteresis <= 1'b1; // U >= 1,14V -> after_hysteresis = 1
+ else if(adc_d < 8) after_hysteresis <= 1'b0; // U < 1,04V -> after_hysteresis = 0
+ // Note: was >= 3,53V and <= 1,19V. The new trigger values allow more reliable detection of the first bit
+ // (it might not reach 3,53V due to the high time constant of the high pass filter in the analogue RF part).
+ // In addition, the new values are more in line with ISO14443-2: "The PICC shall detect the ”End of Pause” after the field exceeds
+ // 5% of H_INITIAL and before it exceeds 60% of H_INITIAL." Depending on the signal strength, 60% might well be less than 3,53V.
- if(~(| adc_d[7:0]))
- begin
- if(deep_counter == 3'd7)
- begin
- deep_modulation <= 1'b1;
- saw_deep_modulation <= 8'd0;
- end
- else
- deep_counter <= deep_counter + 1;
- end
- else
- begin
- deep_counter <= 3'd0;
- if(saw_deep_modulation == 8'd255)
- deep_modulation <= 1'b0;
- else
- saw_deep_modulation <= saw_deep_modulation + 1;
- end
- if(after_hysteresis)
+ // detecting a loss of reader's field (adc_d < 192 for 4096 clock cycles). If this is the case,
+ // set the detected reader signal (after_hysteresis) to '1' (unmodulated)
+ if(adc_d >= 192)
begin
- has_been_low_for <= 7'b0;
+ has_been_low_for <= 12'd0;
end
else
begin
after_hysteresis <= 1'b1;
end
else
+ begin
has_been_low_for <= has_been_low_for + 1;
+ end
end
+
end
-// Report every 4 subcarrier cycles
-// 64 periods of carrier frequency => 6-bit counter [negedge_cnt]
-reg [5:0] negedge_cnt;
-reg bit1, bit2, bit3;
-reg [3:0] count_ones;
-reg [3:0] count_zeros;
-wire [7:0] avg;
-reg [7:0] lavg;
-reg signed [12:0] step1;
-reg signed [12:0] step2;
-reg [7:0] stepsize;
-reg curbit;
-reg [12:0] average;
-wire signed [9:0] dif;
-// A register to send the results to the arm
-reg signed [7:0] to_arm;
-assign avg[7:0] = average[11:4];
-assign dif = lavg - avg;
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Reader -> PM3
+// detect when a reader is active (modulating). We assume that the reader is active, if we see the carrier off for at least 8
+// carrier cycles. We assume that the reader is inactive, if the carrier stayed high for at least 256 carrier cycles.
+reg deep_modulation;
+reg [2:0] deep_counter;
+reg [8:0] saw_deep_modulation;
+
+always @(negedge adc_clk)
+begin
+ if(~(| adc_d[7:0])) // if adc_d == 0 (U <= 0,94V)
+ begin
+ if(deep_counter == 3'd7) // adc_d == 0 for 8 adc_clk ticks -> deep_modulation (by reader)
+ begin
+ deep_modulation <= 1'b1;
+ saw_deep_modulation <= 8'd0;
+ end
+ else
+ deep_counter <= deep_counter + 1;
+ end
+ else
+ begin
+ deep_counter <= 3'd0;
+ if(saw_deep_modulation == 8'd255) // adc_d != 0 for 256 adc_clk ticks -> deep_modulation is over, probably waiting for tag's response
+ deep_modulation <= 1'b0;
+ else
+ saw_deep_modulation <= saw_deep_modulation + 1;
+ end
+end
-reg bit_to_arm;
-reg fdt_indicator, fdt_elapsed;
-reg [10:0] fdt_counter;
-reg [47:0] mod_sig_buf;
-wire mod_sig_buf_empty;
-reg [5:0] mod_sig_ptr;
-reg [3:0] mod_sig_flip;
-reg mod_sig, mod_sig_coil;
-reg temp_buffer_reset;
-reg sendbit;
-assign mod_sig_buf_empty = ~(|mod_sig_buf[47:0]);
-reg [2:0] ssp_frame_counter;
-// ADC data appears on the rising edge, so sample it on the falling edge
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Tag -> PM3
+// filter the input for a tag's signal. The filter box needs the 4 previous input values and is a gaussian derivative filter
+// for noise reduction and edge detection.
+// store 4 previous samples:
+reg [7:0] input_prev_4, input_prev_3, input_prev_2, input_prev_1;
+// convert to signed signals (and multiply by two for samples at t-4 and t)
+wire signed [10:0] input_prev_4_times_2 = {0, 0, input_prev_4, 0};
+wire signed [10:0] input_prev_3_times_1 = {0, 0, 0, input_prev_3};
+wire signed [10:0] input_prev_1_times_1 = {0, 0, 0, input_prev_1};
+wire signed [10:0] adc_d_times_2 = {0, 0, adc_d, 0};
+
+wire signed [10:0] tmp_1, tmp_2;
+wire signed [10:0] adc_d_filtered;
+integer i;
+
+assign tmp_1 = input_prev_4_times_2 + input_prev_3_times_1;
+assign tmp_2 = input_prev_1_times_1 + adc_d_times_2;
+
always @(negedge adc_clk)
begin
+ // for (i = 3; i > 0; i = i - 1)
+ // begin
+ // input_shift[i] <= input_shift[i-1];
+ // end
+ // input_shift[0] <= adc_d;
+ input_prev_4 <= input_prev_3;
+ input_prev_3 <= input_prev_2;
+ input_prev_2 <= input_prev_1;
+ input_prev_1 <= adc_d;
+end
+
+// assign adc_d_filtered = (input_shift[3] << 1) + input_shift[2] - input_shift[0] - (adc_d << 1);
+assign adc_d_filtered = tmp_1 - tmp_2;
- // last bit = 0 then fdt = 1172, in case of 0x26 (7-bit command, LSB first!)
- // last bit = 1 then fdt = 1236, in case of 0x52 (7-bit command, LSB first!)
- if(fdt_counter == 11'd740) fdt_indicator = 1'b1;
- if(fdt_counter == 11'd1148)
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// internal FPGA timing. Maximum required period is 128 carrier clock cycles for a full 8 Bit transfer to ARM. (i.e. we need a
+// 7 bit counter). Adjust its frequency to external reader's clock when simulating a tag or sniffing.
+reg pre_after_hysteresis;
+reg [3:0] reader_falling_edge_time;
+reg [6:0] negedge_cnt;
+
+always @(negedge adc_clk)
+begin
+ // detect a reader signal's falling edge and remember its timing:
+ pre_after_hysteresis <= after_hysteresis;
+ if (pre_after_hysteresis && ~after_hysteresis)
+ begin
+ reader_falling_edge_time[3:0] <= negedge_cnt[3:0];
+ end
+
+ // adjust internal timer counter if necessary:
+ if (negedge_cnt[3:0] == 4'd13 && (mod_type == `SNIFFER || mod_type == `TAGSIM_LISTEN) && deep_modulation)
begin
- if(fdt_elapsed)
+ if (reader_falling_edge_time == 4'd1) // reader signal changes right after sampling. Better sample earlier next time.
begin
- if(negedge_cnt[3:0] == mod_sig_flip[3:0]) mod_sig_coil <= mod_sig;
+ negedge_cnt <= negedge_cnt + 2; // time warp
+ end
+ else if (reader_falling_edge_time == 4'd0) // reader signal changes right before sampling. Better sample later next time.
+ begin
+ negedge_cnt <= negedge_cnt; // freeze time
end
else
begin
- mod_sig_flip[3:0] <= negedge_cnt[3:0];
- mod_sig_coil <= mod_sig;
- fdt_elapsed = 1'b1;
- fdt_indicator = 1'b0;
-
- if(~(| mod_sig_ptr[5:0])) mod_sig_ptr <= 6'b001001;
- else temp_buffer_reset = 1'b1; // fix position of the buffer pointer
+ negedge_cnt <= negedge_cnt + 1; // Continue as usual
end
+ reader_falling_edge_time[3:0] <= 4'd8; // adjust only once per detected edge
end
+ else if (negedge_cnt == 7'd127) // normal operation: count from 0 to 127
+ begin
+ negedge_cnt <= 0;
+ end
else
begin
- fdt_counter <= fdt_counter + 1;
+ negedge_cnt <= negedge_cnt + 1;
end
-
- if(& negedge_cnt[3:0])
+end
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Tag -> PM3:
+// determine best possible time for starting/resetting the modulation detector.
+reg [3:0] mod_detect_reset_time;
+
+always @(negedge adc_clk)
+begin
+ if (mod_type == `READER_LISTEN)
+ // (our) reader signal changes at t=1, tag response expected n*16+4 ticks later, further delayed by
+ // 3 ticks ADC conversion.
+ // 1 + 4 + 3 = 8
+ begin
+ mod_detect_reset_time <= 4'd8;
+ end
+ else
+ if (mod_type == `SNIFFER)
begin
- // When there is a dip in the signal and not in reader mode
- if(~after_hysteresis && mod_sig_buf_empty && ~((mod_type == 3'b100) || (mod_type == 3'b011) || (mod_type == 3'b010))) // last condition to prevent reset
+ // detect a rising edge of reader's signal and sync modulation detector to the tag's answer:
+ if (~pre_after_hysteresis && after_hysteresis && deep_modulation)
+ // reader signal rising edge detected at negedge_cnt[3:0]. This signal had been delayed
+ // 9 ticks by the RF part + 3 ticks by the A/D converter + 1 tick to assign to after_hysteresis.
+ // The tag will respond n*16 + 4 ticks later + 3 ticks A/D converter delay.
+ // - 9 - 3 - 1 + 4 + 3 = -6
begin
- fdt_counter <= 11'd0;
- fdt_elapsed = 1'b0;
- fdt_indicator = 1'b0;
- temp_buffer_reset = 1'b0;
- mod_sig_ptr <= 6'b000000;
+ mod_detect_reset_time <= negedge_cnt[3:0] - 4'd4;
end
-
- lavg <= avg;
-
- if(stepsize<16) stepsize = 8'd16;
+ end
+end
- if(dif>0)
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Tag -> PM3:
+// modulation detector. Looks for the steepest falling and rising edges within a 16 clock period. If there is both a significant
+// falling and rising edge (in any order), a modulation is detected.
+reg signed [10:0] rx_mod_falling_edge_max;
+reg signed [10:0] rx_mod_rising_edge_max;
+reg curbit;
+
+always @(negedge adc_clk)
+begin
+ if(negedge_cnt[3:0] == mod_detect_reset_time)
+ begin
+ // detect modulation signal: if modulating, there must have been a falling AND a rising edge
+ if (rx_mod_falling_edge_max > 5 && rx_mod_rising_edge_max > 5)
+ curbit <= 1'b1; // modulation
+ else
+ curbit <= 1'b0; // no modulation
+ // reset modulation detector
+ rx_mod_rising_edge_max <= 0;
+ rx_mod_falling_edge_max <= 0;
+ end
+ else // look for steepest edges (slopes)
+ begin
+ if (adc_d_filtered > 0)
begin
- step1 = dif*3;
- step2 = stepsize*2; // 3:2
- if(step1>step2)
- begin
- curbit = 1'b0;
- stepsize = dif;
- end
+ if (adc_d_filtered > rx_mod_falling_edge_max)
+ rx_mod_falling_edge_max <= adc_d_filtered;
end
else
begin
- step1 = dif*3;
- step1 = -step1;
- step2 = stepsize*2;
- if(step1>step2)
- begin
- curbit = 1'b1;
- stepsize = -dif;
- end
+ if (-adc_d_filtered > rx_mod_rising_edge_max)
+ rx_mod_rising_edge_max <= -adc_d_filtered;
end
-
- if(curbit)
- begin
- count_zeros <= 4'd0;
- if(& count_ones[3:2])
+ end
+
+end
+
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Tag+Reader -> PM3
+// sample 4 bits reader data and 4 bits tag data for sniffing
+reg [3:0] reader_data;
+reg [3:0] tag_data;
+
+always @(negedge adc_clk)
+begin
+ if(negedge_cnt[3:0] == 4'd0)
+ begin
+ reader_data[3:0] <= {reader_data[2:0], after_hysteresis};
+ tag_data[3:0] <= {tag_data[2:0], curbit};
+ end
+end
+
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// PM3 -> Tag:
+// a delay line to ensure that we send the (emulated) tag's answer at the correct time according to ISO14443-3
+reg [31:0] mod_sig_buf;
+reg [4:0] mod_sig_ptr;
+reg mod_sig;
+
+always @(negedge adc_clk)
+begin
+ if(negedge_cnt[3:0] == 4'd0) // sample data at rising edge of ssp_clk - ssp_dout changes at the falling edge.
+ begin
+ mod_sig_buf[31:2] <= mod_sig_buf[30:1]; // shift
+ if (~ssp_dout && ~mod_sig_buf[1])
+ mod_sig_buf[1] <= 1'b0; // delete the correction bit (a single 1 preceded and succeeded by 0)
+ else
+ mod_sig_buf[1] <= mod_sig_buf[0];
+ mod_sig_buf[0] <= ssp_dout; // add new data to the delay line
+
+ mod_sig = mod_sig_buf[mod_sig_ptr]; // the delayed signal.
+ end
+end
+
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// PM3 -> Tag, internal timing:
+// a timer for the 1172 cycles fdt (Frame Delay Time). Start the timer with a rising edge of the reader's signal.
+// set fdt_elapsed when we no longer need to delay data. Set fdt_indicator when we can start sending data.
+// Note: the FPGA only takes care for the 1172 delay. To achieve an additional 1236-1172=64 ticks delay, the ARM must send
+// a correction bit (before the start bit). The correction bit will be coded as 00010000, i.e. it adds 4 bits to the
+// transmission stream, causing the required additional delay.
+reg [10:0] fdt_counter;
+reg fdt_indicator, fdt_elapsed;
+reg [3:0] mod_sig_flip;
+reg [3:0] sub_carrier_cnt;
+
+// we want to achieve a delay of 1172. The RF part already has delayed the reader signals's rising edge
+// by 9 ticks, the ADC took 3 ticks and there is always a delay of 32 ticks by the mod_sig_buf. Therefore need to
+// count to 1172 - 9 - 3 - 32 = 1128
+`define FDT_COUNT 11'd1128
+
+// The ARM must not send too early, otherwise the mod_sig_buf will overflow, therefore signal that we are ready
+// with fdt_indicator. The mod_sig_buf can buffer 29 excess data bits, i.e. a maximum delay of 29 * 16 = 464 adc_clk ticks.
+// fdt_indicator could appear at ssp_din after 1 tick, the transfer needs 16 ticks, the ARM can send 128 ticks later.
+// 1128 - 464 - 1 - 128 - 8 = 535
+`define FDT_INDICATOR_COUNT 11'd535
+
+// reset on a pause in listen mode. I.e. the counter starts when the pause is over:
+assign fdt_reset = ~after_hysteresis && mod_type == `TAGSIM_LISTEN;
+
+always @(negedge adc_clk)
+begin
+ if (fdt_reset)
+ begin
+ fdt_counter <= 11'd0;
+ fdt_elapsed <= 1'b0;
+ fdt_indicator <= 1'b0;
+ end
+ else
+ begin
+ if(fdt_counter == `FDT_COUNT)
+ begin
+ if(~fdt_elapsed) // just reached fdt.
begin
- curbit = 1'b0; // suppressed signal
- stepsize = 8'd24; // just a fine number
+ mod_sig_flip <= negedge_cnt[3:0]; // start modulation at this time
+ sub_carrier_cnt <= 4'd0; // subcarrier phase in sync with start of modulation
+ fdt_elapsed <= 1'b1;
end
else
begin
- count_ones <= count_ones + 1;
- end
- end
+ sub_carrier_cnt <= sub_carrier_cnt + 1;
+ end
+ end
else
begin
- count_ones <= 4'd0;
- if(& count_zeros[3:0])
+ fdt_counter <= fdt_counter + 1;
+ end
+ end
+
+ if(fdt_counter == `FDT_INDICATOR_COUNT) fdt_indicator <= 1'b1;
+end
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// PM3 -> Reader or Tag
+// assign a modulation signal to the antenna. This signal is either a delayed signal (to achieve fdt when sending to a reader)
+// or undelayed when sending to a tag
+reg mod_sig_coil;
+
+always @(negedge adc_clk)
+begin
+ if (mod_type == `TAGSIM_MOD) // need to take care of proper fdt timing
+ begin
+ if(fdt_counter == `FDT_COUNT)
+ begin
+ if(fdt_elapsed)
begin
- stepsize = 8'd24;
+ if(negedge_cnt[3:0] == mod_sig_flip) mod_sig_coil <= mod_sig;
end
else
begin
- count_zeros <= count_zeros + 1;
+ mod_sig_coil <= mod_sig; // just reached fdt. Immediately assign signal to coil
end
end
-
- // What do we communicate to the ARM
- if(mod_type == 3'b001) sendbit = after_hysteresis;
- else if(mod_type == 3'b010)
+ end
+ else // other modes: don't delay
+ begin
+ mod_sig_coil <= ssp_dout;
+ end
+end
+
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// PM3 -> Reader
+// determine the required delay in the mod_sig_buf (set mod_sig_ptr).
+reg temp_buffer_reset;
+
+always @(negedge adc_clk)
+begin
+ if(fdt_reset)
+ begin
+ mod_sig_ptr <= 5'd0;
+ temp_buffer_reset = 1'b0;
+ end
+ else
+ begin
+ if(fdt_counter == `FDT_COUNT && ~fdt_elapsed) // if we just reached fdt
+ if(~(| mod_sig_ptr[4:0]))
+ mod_sig_ptr <= 5'd8; // ... but didn't buffer a 1 yet, delay next 1 by n*128 ticks.
+ else
+ temp_buffer_reset = 1'b1; // else no need for further delays.
+
+ if(negedge_cnt[3:0] == 4'd0) // at rising edge of ssp_clk - ssp_dout changes at the falling edge.
begin
- if(fdt_counter > 11'd772) sendbit = mod_sig_coil;
- else sendbit = fdt_indicator;
+ if((ssp_dout || (| mod_sig_ptr[4:0])) && ~fdt_elapsed) // buffer a 1 (and all subsequent data) until fdt is reached.
+ if (mod_sig_ptr == 5'd31)
+ mod_sig_ptr <= 5'd0; // buffer overflow - data loss.
+ else
+ mod_sig_ptr <= mod_sig_ptr + 1; // increase buffer (= increase delay by 16 adc_clk ticks). mod_sig_ptr always points ahead of first 1.
+ else if(fdt_elapsed && ~temp_buffer_reset)
+ begin
+ // wait for the next 1 after fdt_elapsed before fixing the delay and starting modulation. This ensures that the response can only happen
+ // at intervals of 8 * 16 = 128 adc_clk ticks (as defined in ISO14443-3)
+ if(ssp_dout)
+ temp_buffer_reset = 1'b1;
+ if(mod_sig_ptr == 5'd1)
+ mod_sig_ptr <= 5'd8; // still nothing received, need to go for the next interval
+ else
+ mod_sig_ptr <= mod_sig_ptr - 1; // decrease buffer.
+ end
end
- else if(mod_type == 3'b011) sendbit = curbit;
- else sendbit = 1'b0;
-
end
+end
- if(~(| negedge_cnt[3:0])) average <= adc_d;
- else average <= average + adc_d;
- if(negedge_cnt == 7'd63)
- begin
- if(deep_modulation)
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// FPGA -> ARM communication:
+// buffer 8 bits data to be sent to ARM. Shift them out bit by bit.
+reg [7:0] to_arm;
+
+always @(negedge adc_clk)
+begin
+ if (negedge_cnt[5:0] == 6'd63) // fill the buffer
+ begin
+ if (mod_type == `SNIFFER)
begin
- to_arm <= {after_hysteresis_prev1,after_hysteresis_prev2,after_hysteresis_prev3,after_hysteresis,1'b0,1'b0,1'b0,1'b0};
+ if(deep_modulation) // a reader is sending (or there's no field at all)
+ begin
+ to_arm <= {reader_data[3:0], 4'b0000}; // don't send tag data
+ end
+ else
+ begin
+ to_arm <= {reader_data[3:0], tag_data[3:0]};
+ end
end
else
begin
- to_arm <= {after_hysteresis_prev1,after_hysteresis_prev2,after_hysteresis_prev3,after_hysteresis,bit1,bit2,bit3,curbit};
- end
-
- negedge_cnt <= 0;
-
+ to_arm[7:0] <= {mod_sig_ptr[4:0], mod_sig_flip[3:1]}; // feedback timing information
end
- else
- begin
- negedge_cnt <= negedge_cnt + 1;
- end
+ end
- if(negedge_cnt == 6'd15)
+ if(negedge_cnt[2:0] == 3'b000 && mod_type == `SNIFFER) // shift at double speed
begin
- after_hysteresis_prev1 <= after_hysteresis;
- bit1 <= curbit;
- end
- if(negedge_cnt == 6'd31)
- begin
- after_hysteresis_prev2 <= after_hysteresis;
- bit2 <= curbit;
- end
- if(negedge_cnt == 6'd47)
- begin
- after_hysteresis_prev3 <= after_hysteresis;
- bit3 <= curbit;
+ // Don't shift if we just loaded new data, obviously.
+ if(negedge_cnt[5:0] != 6'd0)
+ begin
+ to_arm[7:1] <= to_arm[6:0];
+ end
end
-
- if(mod_type != 3'b000)
+ if(negedge_cnt[3:0] == 4'b0000 && mod_type != `SNIFFER)
begin
- if(negedge_cnt[3:0] == 4'b1000)
+ // Don't shift if we just loaded new data, obviously.
+ if(negedge_cnt[6:0] != 7'd0)
begin
- // The modulation signal of the tag
- mod_sig_buf[47:0] <= {mod_sig_buf[46:1], ssp_dout, 1'b0};
- if((ssp_dout || (| mod_sig_ptr[5:0])) && ~fdt_elapsed)
- if(mod_sig_ptr == 6'b101110)
- begin
- mod_sig_ptr <= 6'b000000;
- end
- else mod_sig_ptr <= mod_sig_ptr + 1;
- else if(fdt_elapsed && ~temp_buffer_reset)
- begin
- if(ssp_dout) temp_buffer_reset = 1'b1;
- if(mod_sig_ptr == 6'b000010) mod_sig_ptr <= 6'b001001;
- else mod_sig_ptr <= mod_sig_ptr - 1;
- end
- else
- begin
- // side effect: when ptr = 1 it will cancel the first 1 of every block of ones
- if(~mod_sig_buf[mod_sig_ptr-1] && ~mod_sig_buf[mod_sig_ptr+1]) mod_sig = 1'b0;
- else mod_sig = mod_sig_buf[mod_sig_ptr] & fdt_elapsed; // & fdt_elapsed was for direct relay to oe4
- end
+ to_arm[7:1] <= to_arm[6:0];
end
end
- // SSP Clock and data
- if(mod_type == 3'b000)
+end
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// FPGA -> ARM communication:
+// generate a ssp clock and ssp frame signal for the synchronous transfer from/to the ARM
+reg ssp_clk;
+reg ssp_frame;
+reg [2:0] ssp_frame_counter;
+
+always @(negedge adc_clk)
+begin
+ if(mod_type == `SNIFFER)
+ // SNIFFER mode (ssp_clk = adc_clk / 8, ssp_frame clock = adc_clk / 64)):
begin
- if(negedge_cnt[2:0] == 3'b100)
- ssp_clk <= 1'b0;
-
- if(negedge_cnt[2:0] == 3'b000)
- begin
+ if(negedge_cnt[2:0] == 3'd0)
ssp_clk <= 1'b1;
- // Don't shift if we just loaded new data, obviously.
- if(negedge_cnt != 7'd0)
- begin
- to_arm[7:1] <= to_arm[6:0];
- end
- end
+ if(negedge_cnt[2:0] == 3'd4)
+ ssp_clk <= 1'b0;
- if(negedge_cnt[5:4] == 2'b00)
- ssp_frame = 1'b1;
- else
- ssp_frame = 1'b0;
-
- bit_to_arm = to_arm[7];
+ if(negedge_cnt[5:0] == 6'd0) // ssp_frame rising edge indicates start of frame
+ ssp_frame <= 1'b1;
+ if(negedge_cnt[5:0] == 6'd8)
+ ssp_frame <= 1'b0;
end
else
+ // all other modes (ssp_clk = adc_clk / 16, ssp_frame clock = adc_clk / 128):
begin
- if(negedge_cnt[3:0] == 4'b1000) ssp_clk <= 1'b0;
+ if(negedge_cnt[3:0] == 4'd0)
+ ssp_clk <= 1'b1;
+ if(negedge_cnt[3:0] == 4'd8)
+ ssp_clk <= 1'b0;
- if(negedge_cnt[3:0] == 4'b0111)
- begin
- if(ssp_frame_counter == 3'd7) ssp_frame_counter <= 3'd0;
- else ssp_frame_counter <= ssp_frame_counter + 1;
- end
+ if(negedge_cnt[6:0] == 7'd7) // ssp_frame rising edge indicates start of frame
+ ssp_frame <= 1'b1;
+ if(negedge_cnt[6:0] == 7'd23)
+ ssp_frame <= 1'b0;
+ end
+end
- if(negedge_cnt[3:0] == 4'b0000)
- begin
- ssp_clk <= 1'b1;
- end
-
- ssp_frame = (ssp_frame_counter == 3'd7);
-
- bit_to_arm = sendbit;
+
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// FPGA -> ARM communication:
+// select the data to be sent to ARM
+reg bit_to_arm;
+reg sendbit;
+
+always @(negedge adc_clk)
+begin
+ if(negedge_cnt[3:0] == 4'd0)
+ begin
+ // What do we communicate to the ARM
+ if(mod_type == `TAGSIM_LISTEN)
+ sendbit = after_hysteresis;
+ else if(mod_type == `TAGSIM_MOD)
+ /* if(fdt_counter > 11'd772) sendbit = mod_sig_coil; // huh?
+ else */
+ sendbit = fdt_indicator;
+ else if (mod_type == `READER_LISTEN)
+ sendbit = curbit;
+ else
+ sendbit = 1'b0;
end
-
+
+
+ if(mod_type == `SNIFFER)
+ // send sampled reader and tag data:
+ bit_to_arm = to_arm[7];
+ else if (mod_type == `TAGSIM_MOD && fdt_elapsed && temp_buffer_reset)
+ // send timing information:
+ bit_to_arm = to_arm[7];
+ else
+ // send data or fdt_indicator
+ bit_to_arm = sendbit;
end
+
+
+
assign ssp_din = bit_to_arm;
-// Modulating carrier frequency is fc/16
-wire modulating_carrier;
-assign modulating_carrier = (mod_sig_coil & negedge_cnt[3] & (mod_type == 3'b010));
-assign pwr_hi = (ck_1356megb & (((mod_type == 3'b100) & ~mod_sig_coil) || (mod_type == 3'b011)));
+// Subcarrier (adc_clk/16, for TAGSIM_MOD only).
+wire sub_carrier;
+assign sub_carrier = ~sub_carrier_cnt[3];
-// This one is all LF, so doesn't matter
-//assign pwr_oe2 = modulating_carrier;
-assign pwr_oe2 = 1'b0;
+// in READER_MOD: drop carrier for mod_sig_coil==1 (pause); in READER_LISTEN: carrier always on; in other modes: carrier always off
+assign pwr_hi = (ck_1356megb & (((mod_type == `READER_MOD) & ~mod_sig_coil) || (mod_type == `READER_LISTEN)));
-// Toggle only one of these, since we are already producing much deeper
-// modulation than a real tag would.
-//assign pwr_oe1 = modulating_carrier;
-assign pwr_oe1 = 1'b0;
-assign pwr_oe4 = modulating_carrier;
-//assign pwr_oe4 = 1'b0;
-// This one is always on, so that we can watch the carrier.
-//assign pwr_oe3 = modulating_carrier;
+// Enable HF antenna drivers:
+assign pwr_oe1 = 1'b0;
assign pwr_oe3 = 1'b0;
+// TAGSIM_MOD: short circuit antenna with different resistances (modulated by sub_carrier modulated by mod_sig_coil)
+// for pwr_oe4 = 1 (tristate): antenna load = 10k || 33 = 32,9 Ohms
+// for pwr_oe4 = 0 (active): antenna load = 10k || 33 || 33 = 16,5 Ohms
+assign pwr_oe4 = mod_sig_coil & sub_carrier & (mod_type == `TAGSIM_MOD);
-assign dbg = negedge_cnt[3];
-
-// Unused.
+// This is all LF, so doesn't matter.
+assign pwr_oe2 = 1'b0;
assign pwr_lo = 1'b0;
+
+assign dbg = negedge_cnt[3];
+
endmodule
projects / proxmark3-svn / blobdiff