+// return start index of best starting position for that clock and return clock (by reference)
+int DetectASKClock(uint8_t dest[], size_t size, int *clock, int maxErr)
+{
+ size_t i=1;
+ uint8_t clk[] = {255,8,16,32,40,50,64,100,128,255};
+ uint8_t clkEnd = 9;
+ uint8_t loopCnt = 255; //don't need to loop through entire array...
+ if (size <= loopCnt+60) return -1; //not enough samples
+ size -= 60; //sometimes there is a strange end wave - filter out this....
+ //if we already have a valid clock
+ uint8_t clockFnd=0;
+ for (;i<clkEnd;++i)
+ if (clk[i] == *clock) clockFnd = i;
+ //clock found but continue to find best startpos
+
+ //get high and low peak
+ int peak, low;
+ if (getHiLo(dest, loopCnt, &peak, &low, 75, 75) < 1) return -1;
+
+ //test for large clean peaks
+ if (!clockFnd){
+ if (DetectCleanAskWave(dest, size, peak, low)==1){
+ int ans = DetectStrongAskClock(dest, size, peak, low);
+ if (g_debugMode==2) prnt("DEBUG ASK: detectaskclk Clean Ask Wave Detected: clk %d",ans);
+ for (i=clkEnd-1; i>0; i--){
+ if (clk[i] == ans) {
+ *clock = ans;
+ //clockFnd = i;
+ return 0; // for strong waves i don't use the 'best start position' yet...
+ //break; //clock found but continue to find best startpos [not yet]
+ }
+ }
+ }
+ }
+ uint8_t ii;
+ uint8_t clkCnt, tol = 0;
+ uint16_t bestErr[]={1000,1000,1000,1000,1000,1000,1000,1000,1000};
+ uint8_t bestStart[]={0,0,0,0,0,0,0,0,0};
+ size_t errCnt = 0;
+ size_t arrLoc, loopEnd;
+
+ if (clockFnd>0) {
+ clkCnt = clockFnd;
+ clkEnd = clockFnd+1;
+ }
+ else clkCnt=1;
+
+ //test each valid clock from smallest to greatest to see which lines up
+ for(; clkCnt < clkEnd; clkCnt++){
+ if (clk[clkCnt] <= 32){
+ tol=1;
+ }else{
+ tol=0;
+ }
+ //if no errors allowed - keep start within the first clock
+ if (!maxErr && size > clk[clkCnt]*2 + tol && clk[clkCnt]<128) loopCnt=clk[clkCnt]*2;
+ bestErr[clkCnt]=1000;
+ //try lining up the peaks by moving starting point (try first few clocks)
+ for (ii=0; ii < loopCnt; ii++){
+ if (dest[ii] < peak && dest[ii] > low) continue;
+
+ errCnt=0;
+ // now that we have the first one lined up test rest of wave array
+ loopEnd = ((size-ii-tol) / clk[clkCnt]) - 1;
+ for (i=0; i < loopEnd; ++i){
+ arrLoc = ii + (i * clk[clkCnt]);
+ if (dest[arrLoc] >= peak || dest[arrLoc] <= low){
+ }else if (dest[arrLoc-tol] >= peak || dest[arrLoc-tol] <= low){
+ }else if (dest[arrLoc+tol] >= peak || dest[arrLoc+tol] <= low){
+ }else{ //error no peak detected
+ errCnt++;
+ }
+ }
+ //if we found no errors then we can stop here and a low clock (common clocks)
+ // this is correct one - return this clock
+ if (g_debugMode == 2) prnt("DEBUG ASK: clk %d, err %d, startpos %d, endpos %d",clk[clkCnt],errCnt,ii,i);
+ if(errCnt==0 && clkCnt<7) {
+ if (!clockFnd) *clock = clk[clkCnt];
+ return ii;
+ }
+ //if we found errors see if it is lowest so far and save it as best run
+ if(errCnt<bestErr[clkCnt]){
+ bestErr[clkCnt]=errCnt;
+ bestStart[clkCnt]=ii;
+ }
+ }
+ }
+ uint8_t iii;
+ uint8_t best=0;
+ for (iii=1; iii<clkEnd; ++iii){
+ if (bestErr[iii] < bestErr[best]){
+ if (bestErr[iii] == 0) bestErr[iii]=1;
+ // current best bit to error ratio vs new bit to error ratio
+ if ( (size/clk[best])/bestErr[best] < (size/clk[iii])/bestErr[iii] ){
+ best = iii;
+ }
+ }
+ if (g_debugMode == 2) prnt("DEBUG ASK: clk %d, # Errors %d, Current Best Clk %d, bestStart %d",clk[iii],bestErr[iii],clk[best],bestStart[best]);
+ }
+ if (!clockFnd) *clock = clk[best];
+ return bestStart[best];
+}
+
+//by marshmellow
+//detect psk clock by reading each phase shift
+// a phase shift is determined by measuring the sample length of each wave
+int DetectPSKClock(uint8_t dest[], size_t size, int clock)
+{
+ uint8_t clk[]={255,16,32,40,50,64,100,128,255}; //255 is not a valid clock
+ uint16_t loopCnt = 4096; //don't need to loop through entire array...
+ if (size == 0) return 0;
+ if (size<loopCnt) loopCnt = size-20;
+
+ //if we already have a valid clock quit
+ size_t i=1;
+ for (; i < 8; ++i)
+ if (clk[i] == clock) return clock;
+
+ size_t waveStart=0, waveEnd=0, firstFullWave=0, lastClkBit=0;
+ uint8_t clkCnt, fc=0, fullWaveLen=0, tol=1;
+ uint16_t peakcnt=0, errCnt=0, waveLenCnt=0;
+ uint16_t bestErr[]={1000,1000,1000,1000,1000,1000,1000,1000,1000};
+ uint16_t peaksdet[]={0,0,0,0,0,0,0,0,0};
+ fc = countFC(dest, size, 0);
+ if (fc!=2 && fc!=4 && fc!=8) return -1;
+ if (g_debugMode==2) prnt("DEBUG PSK: FC: %d",fc);
+
+ //find first full wave
+ for (i=160; i<loopCnt; i++){
+ if (dest[i] < dest[i+1] && dest[i+1] >= dest[i+2]){
+ if (waveStart == 0) {
+ waveStart = i+1;
+ //prnt("DEBUG: waveStart: %d",waveStart);
+ } else {
+ waveEnd = i+1;
+ //prnt("DEBUG: waveEnd: %d",waveEnd);
+ waveLenCnt = waveEnd-waveStart;
+ if (waveLenCnt > fc){
+ firstFullWave = waveStart;
+ fullWaveLen=waveLenCnt;
+ break;
+ }
+ waveStart=0;
+ }
+ }
+ }
+ if (g_debugMode ==2) prnt("DEBUG PSK: firstFullWave: %d, waveLen: %d",firstFullWave,fullWaveLen);
+
+ //test each valid clock from greatest to smallest to see which lines up
+ for(clkCnt=7; clkCnt >= 1 ; clkCnt--){
+ lastClkBit = firstFullWave; //set end of wave as clock align
+ waveStart = 0;
+ errCnt=0;
+ peakcnt=0;
+ if (g_debugMode == 2) prnt("DEBUG PSK: clk: %d, lastClkBit: %d",clk[clkCnt],lastClkBit);
+
+ for (i = firstFullWave+fullWaveLen-1; i < loopCnt-2; i++){
+ //top edge of wave = start of new wave
+ if (dest[i] < dest[i+1] && dest[i+1] >= dest[i+2]){
+ if (waveStart == 0) {
+ waveStart = i+1;
+ waveLenCnt=0;
+ } else { //waveEnd
+ waveEnd = i+1;
+ waveLenCnt = waveEnd-waveStart;
+ if (waveLenCnt > fc){
+ //if this wave is a phase shift
+ if (g_debugMode == 2) prnt("DEBUG PSK: phase shift at: %d, len: %d, nextClk: %d, i: %d, fc: %d",waveStart,waveLenCnt,lastClkBit+clk[clkCnt]-tol,i+1,fc);
+ if (i+1 >= lastClkBit + clk[clkCnt] - tol){ //should be a clock bit
+ peakcnt++;
+ lastClkBit+=clk[clkCnt];
+ } else if (i<lastClkBit+8){
+ //noise after a phase shift - ignore
+ } else { //phase shift before supposed to based on clock
+ errCnt++;
+ }
+ } else if (i+1 > lastClkBit + clk[clkCnt] + tol + fc){
+ lastClkBit+=clk[clkCnt]; //no phase shift but clock bit
+ }
+ waveStart=i+1;
+ }
+ }
+ }
+ if (errCnt == 0){
+ return clk[clkCnt];
+ }
+ if (errCnt <= bestErr[clkCnt]) bestErr[clkCnt]=errCnt;
+ if (peakcnt > peaksdet[clkCnt]) peaksdet[clkCnt]=peakcnt;
+ }
+ //all tested with errors
+ //return the highest clk with the most peaks found
+ uint8_t best=7;
+ for (i=7; i>=1; i--){
+ if (peaksdet[i] > peaksdet[best]) {
+ best = i;
+ }
+ if (g_debugMode == 2) prnt("DEBUG PSK: Clk: %d, peaks: %d, errs: %d, bestClk: %d",clk[i],peaksdet[i],bestErr[i],clk[best]);
+ }
+ return clk[best];
+}
+
+int DetectStrongNRZClk(uint8_t *dest, size_t size, int peak, int low){
+ //find shortest transition from high to low
+ size_t i = 0;
+ size_t transition1 = 0;
+ int lowestTransition = 255;
+ bool lastWasHigh = false;
+
+ //find first valid beginning of a high or low wave
+ while ((dest[i] >= peak || dest[i] <= low) && (i < size))
+ ++i;
+ while ((dest[i] < peak && dest[i] > low) && (i < size))
+ ++i;
+ lastWasHigh = (dest[i] >= peak);
+
+ if (i==size) return 0;
+ transition1 = i;
+
+ for (;i < size; i++) {
+ if ((dest[i] >= peak && !lastWasHigh) || (dest[i] <= low && lastWasHigh)) {
+ lastWasHigh = (dest[i] >= peak);
+ if (i-transition1 < lowestTransition) lowestTransition = i-transition1;
+ transition1 = i;
+ }
+ }
+ if (lowestTransition == 255) lowestTransition = 0;
+ if (g_debugMode==2) prnt("DEBUG NRZ: detectstrongNRZclk smallest wave: %d",lowestTransition);
+ return lowestTransition;
+}
+
+//by marshmellow
+//detect nrz clock by reading #peaks vs no peaks(or errors)
+int DetectNRZClock(uint8_t dest[], size_t size, int clock)
+{
+ size_t i=0;
+ uint8_t clk[]={8,16,32,40,50,64,100,128,255};
+ size_t loopCnt = 4096; //don't need to loop through entire array...
+ if (size == 0) return 0;
+ if (size<loopCnt) loopCnt = size-20;
+ //if we already have a valid clock quit
+ for (; i < 8; ++i)
+ if (clk[i] == clock) return clock;
+
+ //get high and low peak
+ int peak, low;
+ if (getHiLo(dest, loopCnt, &peak, &low, 75, 75) < 1) return 0;
+
+ int lowestTransition = DetectStrongNRZClk(dest, size-20, peak, low);
+ size_t ii;
+ uint8_t clkCnt;
+ uint8_t tol = 0;
+ uint16_t smplCnt = 0;
+ int16_t peakcnt = 0;
+ int16_t peaksdet[] = {0,0,0,0,0,0,0,0};
+ uint16_t maxPeak = 255;
+ bool firstpeak = false;
+ //test for large clipped waves
+ for (i=0; i<loopCnt; i++){
+ if (dest[i] >= peak || dest[i] <= low){
+ if (!firstpeak) continue;
+ smplCnt++;
+ } else {
+ firstpeak=true;
+ if (smplCnt > 6 ){
+ if (maxPeak > smplCnt){
+ maxPeak = smplCnt;
+ //prnt("maxPk: %d",maxPeak);
+ }
+ peakcnt++;
+ //prnt("maxPk: %d, smplCnt: %d, peakcnt: %d",maxPeak,smplCnt,peakcnt);
+ smplCnt=0;
+ }
+ }
+ }
+ bool errBitHigh = 0;
+ bool bitHigh = 0;
+ uint8_t ignoreCnt = 0;
+ uint8_t ignoreWindow = 4;
+ bool lastPeakHigh = 0;
+ int lastBit = 0;
+ peakcnt=0;
+ //test each valid clock from smallest to greatest to see which lines up
+ for(clkCnt=0; clkCnt < 8; ++clkCnt){
+ //ignore clocks smaller than smallest peak
+ if (clk[clkCnt] < maxPeak - (clk[clkCnt]/4)) continue;
+ //try lining up the peaks by moving starting point (try first 256)
+ for (ii=20; ii < loopCnt; ++ii){
+ if ((dest[ii] >= peak) || (dest[ii] <= low)){
+ peakcnt=0;
+ bitHigh = false;
+ ignoreCnt = 0;
+ lastBit = ii-clk[clkCnt];
+ //loop through to see if this start location works
+ for (i = ii; i < size-20; ++i) {
+ //if we are at a clock bit
+ if ((i >= lastBit + clk[clkCnt] - tol) && (i <= lastBit + clk[clkCnt] + tol)) {
+ //test high/low
+ if (dest[i] >= peak || dest[i] <= low) {
+ //if same peak don't count it
+ if ((dest[i] >= peak && !lastPeakHigh) || (dest[i] <= low && lastPeakHigh)) {
+ peakcnt++;
+ }
+ lastPeakHigh = (dest[i] >= peak);
+ bitHigh = true;
+ errBitHigh = false;
+ ignoreCnt = ignoreWindow;
+ lastBit += clk[clkCnt];
+ } else if (i == lastBit + clk[clkCnt] + tol) {
+ lastBit += clk[clkCnt];
+ }
+ //else if not a clock bit and no peaks
+ } else if (dest[i] < peak && dest[i] > low){
+ if (ignoreCnt==0){
+ bitHigh=false;
+ if (errBitHigh==true) peakcnt--;
+ errBitHigh=false;
+ } else {
+ ignoreCnt--;
+ }
+ // else if not a clock bit but we have a peak
+ } else if ((dest[i]>=peak || dest[i]<=low) && (!bitHigh)) {
+ //error bar found no clock...
+ errBitHigh=true;
+ }
+ }
+ if(peakcnt>peaksdet[clkCnt]) {
+ peaksdet[clkCnt]=peakcnt;
+ }
+ }
+ }
+ }
+ int iii=7;
+ uint8_t best=0;
+ for (iii=7; iii > 0; iii--){
+ if ((peaksdet[iii] >= (peaksdet[best]-1)) && (peaksdet[iii] <= peaksdet[best]+1) && lowestTransition) {
+ if (clk[iii] > (lowestTransition - (clk[iii]/8)) && clk[iii] < (lowestTransition + (clk[iii]/8))) {
+ best = iii;
+ }
+ } else if (peaksdet[iii] > peaksdet[best]){
+ best = iii;
+ }
+ if (g_debugMode==2) prnt("DEBUG NRZ: Clk: %d, peaks: %d, maxPeak: %d, bestClk: %d, lowestTrs: %d",clk[iii],peaksdet[iii],maxPeak, clk[best], lowestTransition);
+ }
+
+ return clk[best];
+}
+
+// by marshmellow
+// convert psk1 demod to psk2 demod
+// only transition waves are 1s
+void psk1TOpsk2(uint8_t *BitStream, size_t size)
+{
+ size_t i=1;
+ uint8_t lastBit=BitStream[0];
+ for (; i<size; i++){
+ if (BitStream[i]==7){
+ //ignore errors
+ } else if (lastBit!=BitStream[i]){
+ lastBit=BitStream[i];
+ BitStream[i]=1;
+ } else {
+ BitStream[i]=0;
+ }
+ }
+ return;
+}
+
+// by marshmellow
+// convert psk2 demod to psk1 demod
+// from only transition waves are 1s to phase shifts change bit
+void psk2TOpsk1(uint8_t *BitStream, size_t size)
+{
+ uint8_t phase=0;
+ for (size_t i=0; i<size; i++){
+ if (BitStream[i]==1){
+ phase ^=1;
+ }
+ BitStream[i]=phase;
+ }
+ return;
+}
+
+// redesigned by marshmellow adjusted from existing decode functions
+// indala id decoding - only tested on 26 bit tags, but attempted to make it work for more
+int indala26decode(uint8_t *bitStream, size_t *size, uint8_t *invert)
+{
+ //26 bit 40134 format (don't know other formats)
+ uint8_t preamble[] = {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1};
+ uint8_t preamble_i[] = {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,0};
+ size_t startidx = 0;
+ if (!preambleSearch(bitStream, preamble, sizeof(preamble), size, &startidx)){
+ // if didn't find preamble try again inverting
+ if (!preambleSearch(bitStream, preamble_i, sizeof(preamble_i), size, &startidx)) return -1;
+ *invert ^= 1;
+ }
+ if (*size != 64 && *size != 224) return -2;
+ if (*invert==1)
+ for (size_t i = startidx; i < *size; i++)
+ bitStream[i] ^= 1;
+
+ return (int) startidx;
+}
+
+// by marshmellow - demodulate NRZ wave - requires a read with strong signal
+// peaks invert bit (high=1 low=0) each clock cycle = 1 bit determined by last peak
+int nrzRawDemod(uint8_t *dest, size_t *size, int *clk, int *invert){
+ if (justNoise(dest, *size)) return -1;
+ *clk = DetectNRZClock(dest, *size, *clk);
+ if (*clk==0) return -2;
+ size_t i, gLen = 4096;
+ if (gLen>*size) gLen = *size-20;
+ int high, low;
+ if (getHiLo(dest, gLen, &high, &low, 75, 75) < 1) return -3; //25% fuzz on high 25% fuzz on low
+
+ uint8_t bit=0;
+ //convert wave samples to 1's and 0's
+ for(i=20; i < *size-20; i++){
+ if (dest[i] >= high) bit = 1;
+ if (dest[i] <= low) bit = 0;
+ dest[i] = bit;
+ }
+ //now demod based on clock (rf/32 = 32 1's for one 1 bit, 32 0's for one 0 bit)
+ size_t lastBit = 0;
+ size_t numBits = 0;
+ for(i=21; i < *size-20; i++) {
+ //if transition detected or large number of same bits - store the passed bits
+ if (dest[i] != dest[i-1] || (i-lastBit) == (10 * *clk)) {
+ memset(dest+numBits, dest[i-1] ^ *invert, (i - lastBit + (*clk/4)) / *clk);
+ numBits += (i - lastBit + (*clk/4)) / *clk;
+ lastBit = i-1;
+ }
+ }
+ *size = numBits;
+ return 0;
+}
+
+//by marshmellow
+//detects the bit clock for FSK given the high and low Field Clocks
+uint8_t detectFSKClk(uint8_t *BitStream, size_t size, uint8_t fcHigh, uint8_t fcLow)
+{
+ uint8_t clk[] = {8,16,32,40,50,64,100,128,0};
+ uint16_t rfLens[] = {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
+ uint8_t rfCnts[] = {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
+ uint8_t rfLensFnd = 0;
+ uint8_t lastFCcnt = 0;
+ uint16_t fcCounter = 0;
+ uint16_t rfCounter = 0;
+ uint8_t firstBitFnd = 0;
+ size_t i;
+ if (size == 0) return 0;
+
+ uint8_t fcTol = ((fcHigh*100 - fcLow*100)/2 + 50)/100; //(uint8_t)(0.5+(float)(fcHigh-fcLow)/2);
+ rfLensFnd=0;
+ fcCounter=0;
+ rfCounter=0;
+ firstBitFnd=0;
+ //PrintAndLog("DEBUG: fcTol: %d",fcTol);
+ // prime i to first peak / up transition
+ for (i = 160; i < size-20; i++)
+ if (BitStream[i] > BitStream[i-1] && BitStream[i]>=BitStream[i+1])
+ break;
+
+ for (; i < size-20; i++){
+ fcCounter++;
+ rfCounter++;
+
+ if (BitStream[i] <= BitStream[i-1] || BitStream[i] < BitStream[i+1])
+ continue;
+ // else new peak
+ // if we got less than the small fc + tolerance then set it to the small fc
+ if (fcCounter < fcLow+fcTol)
+ fcCounter = fcLow;
+ else //set it to the large fc
+ fcCounter = fcHigh;
+
+ //look for bit clock (rf/xx)
+ if ((fcCounter < lastFCcnt || fcCounter > lastFCcnt)){
+ //not the same size as the last wave - start of new bit sequence
+ if (firstBitFnd > 1){ //skip first wave change - probably not a complete bit
+ for (int ii=0; ii<15; ii++){
+ if (rfLens[ii] >= (rfCounter-4) && rfLens[ii] <= (rfCounter+4)){
+ rfCnts[ii]++;
+ rfCounter = 0;
+ break;
+ }
+ }
+ if (rfCounter > 0 && rfLensFnd < 15){
+ //PrintAndLog("DEBUG: rfCntr %d, fcCntr %d",rfCounter,fcCounter);
+ rfCnts[rfLensFnd]++;
+ rfLens[rfLensFnd++] = rfCounter;
+ }
+ } else {
+ firstBitFnd++;
+ }
+ rfCounter=0;
+ lastFCcnt=fcCounter;
+ }
+ fcCounter=0;
+ }
+ uint8_t rfHighest=15, rfHighest2=15, rfHighest3=15;
+
+ for (i=0; i<15; i++){
+ //get highest 2 RF values (might need to get more values to compare or compare all?)
+ if (rfCnts[i]>rfCnts[rfHighest]){
+ rfHighest3=rfHighest2;
+ rfHighest2=rfHighest;
+ rfHighest=i;
+ } else if(rfCnts[i]>rfCnts[rfHighest2]){
+ rfHighest3=rfHighest2;
+ rfHighest2=i;
+ } else if(rfCnts[i]>rfCnts[rfHighest3]){
+ rfHighest3=i;
+ }
+ if (g_debugMode==2) prnt("DEBUG FSK: RF %d, cnts %d",rfLens[i], rfCnts[i]);
+ }
+ // set allowed clock remainder tolerance to be 1 large field clock length+1
+ // we could have mistakenly made a 9 a 10 instead of an 8 or visa versa so rfLens could be 1 FC off
+ uint8_t tol1 = fcHigh+1;
+
+ if (g_debugMode==2) prnt("DEBUG FSK: most counted rf values: 1 %d, 2 %d, 3 %d",rfLens[rfHighest],rfLens[rfHighest2],rfLens[rfHighest3]);
+
+ // loop to find the highest clock that has a remainder less than the tolerance
+ // compare samples counted divided by
+ // test 128 down to 32 (shouldn't be possible to have fc/10 & fc/8 and rf/16 or less)
+ int ii=7;
+ for (; ii>=2; ii--){
+ if (rfLens[rfHighest] % clk[ii] < tol1 || rfLens[rfHighest] % clk[ii] > clk[ii]-tol1){
+ if (rfLens[rfHighest2] % clk[ii] < tol1 || rfLens[rfHighest2] % clk[ii] > clk[ii]-tol1){
+ if (rfLens[rfHighest3] % clk[ii] < tol1 || rfLens[rfHighest3] % clk[ii] > clk[ii]-tol1){
+ if (g_debugMode==2) prnt("DEBUG FSK: clk %d divides into the 3 most rf values within tolerance",clk[ii]);
+ break;
+ }
+ }
+ }
+ }
+
+ if (ii<0) return 0; // oops we went too far
+
+ return clk[ii];
+}
+
+//by marshmellow
+//countFC is to detect the field clock lengths.
+//counts and returns the 2 most common wave lengths
+//mainly used for FSK field clock detection
+uint16_t countFC(uint8_t *BitStream, size_t size, uint8_t fskAdj)
+{
+ uint8_t fcLens[] = {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
+ uint16_t fcCnts[] = {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
+ uint8_t fcLensFnd = 0;
+ uint8_t lastFCcnt=0;
+ uint8_t fcCounter = 0;
+ size_t i;
+ if (size == 0) return 0;
+
+ // prime i to first up transition
+ for (i = 160; i < size-20; i++)
+ if (BitStream[i] > BitStream[i-1] && BitStream[i] >= BitStream[i+1])
+ break;
+
+ for (; i < size-20; i++){
+ if (BitStream[i] > BitStream[i-1] && BitStream[i] >= BitStream[i+1]){
+ // new up transition
+ fcCounter++;
+ if (fskAdj){
+ //if we had 5 and now have 9 then go back to 8 (for when we get a fc 9 instead of an 8)
+ if (lastFCcnt==5 && fcCounter==9) fcCounter--;
+ //if fc=9 or 4 add one (for when we get a fc 9 instead of 10 or a 4 instead of a 5)
+ if ((fcCounter==9) || fcCounter==4) fcCounter++;
+ // save last field clock count (fc/xx)
+ lastFCcnt = fcCounter;
+ }
+ // find which fcLens to save it to:
+ for (int ii=0; ii<15; ii++){
+ if (fcLens[ii]==fcCounter){
+ fcCnts[ii]++;
+ fcCounter=0;
+ break;
+ }
+ }
+ if (fcCounter>0 && fcLensFnd<15){
+ //add new fc length
+ fcCnts[fcLensFnd]++;
+ fcLens[fcLensFnd++]=fcCounter;
+ }
+ fcCounter=0;
+ } else {
+ // count sample
+ fcCounter++;
+ }
+ }
+
+ uint8_t best1=14, best2=14, best3=14;
+ uint16_t maxCnt1=0;
+ // go through fclens and find which ones are bigest 2
+ for (i=0; i<15; i++){
+ // get the 3 best FC values
+ if (fcCnts[i]>maxCnt1) {
+ best3=best2;
+ best2=best1;
+ maxCnt1=fcCnts[i];
+ best1=i;
+ } else if(fcCnts[i]>fcCnts[best2]){
+ best3=best2;
+ best2=i;
+ } else if(fcCnts[i]>fcCnts[best3]){
+ best3=i;
+ }
+ if (g_debugMode==2) prnt("DEBUG countfc: FC %u, Cnt %u, best fc: %u, best2 fc: %u",fcLens[i],fcCnts[i],fcLens[best1],fcLens[best2]);
+ }
+ if (fcLens[best1]==0) return 0;
+ uint8_t fcH=0, fcL=0;
+ if (fcLens[best1]>fcLens[best2]){
+ fcH=fcLens[best1];
+ fcL=fcLens[best2];
+ } else{
+ fcH=fcLens[best2];
+ fcL=fcLens[best1];
+ }
+ if ((size-180)/fcH/3 > fcCnts[best1]+fcCnts[best2]) {
+ if (g_debugMode==2) prnt("DEBUG countfc: fc is too large: %u > %u. Not psk or fsk",(size-180)/fcH/3,fcCnts[best1]+fcCnts[best2]);
+ return 0; //lots of waves not psk or fsk
+ }
+ // TODO: take top 3 answers and compare to known Field clocks to get top 2
+
+ uint16_t fcs = (((uint16_t)fcH)<<8) | fcL;
+ if (fskAdj) return fcs;
+ return fcLens[best1];
+}
+
+//by marshmellow - demodulate PSK1 wave
+//uses wave lengths (# Samples)
+int pskRawDemod(uint8_t dest[], size_t *size, int *clock, int *invert)
+{
+ if (size == 0) return -1;
+ uint16_t loopCnt = 4096; //don't need to loop through entire array...
+ if (*size<loopCnt) loopCnt = *size;
+
+ size_t numBits=0;
+ uint8_t curPhase = *invert;
+ size_t i, waveStart=1, waveEnd=0, firstFullWave=0, lastClkBit=0;
+ uint8_t fc=0, fullWaveLen=0, tol=1;
+ uint16_t errCnt=0, waveLenCnt=0;
+ fc = countFC(dest, *size, 0);
+ if (fc!=2 && fc!=4 && fc!=8) return -1;
+ //PrintAndLog("DEBUG: FC: %d",fc);
+ *clock = DetectPSKClock(dest, *size, *clock);
+ if (*clock == 0) return -1;
+ int avgWaveVal=0, lastAvgWaveVal=0;
+ //find first phase shift
+ for (i=0; i<loopCnt; i++){
+ if (dest[i]+fc < dest[i+1] && dest[i+1] >= dest[i+2]){
+ waveEnd = i+1;
+ //PrintAndLog("DEBUG: waveEnd: %d",waveEnd);
+ waveLenCnt = waveEnd-waveStart;
+ if (waveLenCnt > fc && waveStart > fc && !(waveLenCnt > fc+2)){ //not first peak and is a large wave but not out of whack
+ lastAvgWaveVal = avgWaveVal/(waveLenCnt);
+ firstFullWave = waveStart;
+ fullWaveLen=waveLenCnt;
+ //if average wave value is > graph 0 then it is an up wave or a 1
+ if (lastAvgWaveVal > 123) curPhase ^= 1; //fudge graph 0 a little 123 vs 128
+ break;
+ }
+ waveStart = i+1;
+ avgWaveVal = 0;
+ }
+ avgWaveVal += dest[i+2];
+ }
+ if (firstFullWave == 0) {
+ // no phase shift detected - could be all 1's or 0's - doesn't matter where we start
+ // so skip a little to ensure we are past any Start Signal
+ firstFullWave = 160;
+ memset(dest, curPhase, firstFullWave / *clock);
+ } else {
+ memset(dest, curPhase^1, firstFullWave / *clock);
+ }
+ //advance bits
+ numBits += (firstFullWave / *clock);
+ //set start of wave as clock align
+ lastClkBit = firstFullWave;
+ if (g_debugMode==2) prnt("DEBUG PSK: firstFullWave: %u, waveLen: %u",firstFullWave,fullWaveLen);
+ if (g_debugMode==2) prnt("DEBUG: clk: %d, lastClkBit: %u, fc: %u", *clock, lastClkBit,(unsigned int) fc);
+ waveStart = 0;
+ dest[numBits++] = curPhase; //set first read bit
+ for (i = firstFullWave + fullWaveLen - 1; i < *size-3; i++){
+ //top edge of wave = start of new wave
+ if (dest[i]+fc < dest[i+1] && dest[i+1] >= dest[i+2]){
+ if (waveStart == 0) {
+ waveStart = i+1;
+ waveLenCnt = 0;
+ avgWaveVal = dest[i+1];
+ } else { //waveEnd
+ waveEnd = i+1;
+ waveLenCnt = waveEnd-waveStart;
+ lastAvgWaveVal = avgWaveVal/waveLenCnt;
+ if (waveLenCnt > fc){
+ //PrintAndLog("DEBUG: avgWaveVal: %d, waveSum: %d",lastAvgWaveVal,avgWaveVal);
+ //this wave is a phase shift
+ //PrintAndLog("DEBUG: phase shift at: %d, len: %d, nextClk: %d, i: %d, fc: %d",waveStart,waveLenCnt,lastClkBit+*clock-tol,i+1,fc);
+ if (i+1 >= lastClkBit + *clock - tol){ //should be a clock bit
+ curPhase ^= 1;
+ dest[numBits++] = curPhase;
+ lastClkBit += *clock;
+ } else if (i < lastClkBit+10+fc){
+ //noise after a phase shift - ignore
+ } else { //phase shift before supposed to based on clock
+ errCnt++;
+ dest[numBits++] = 7;
+ }
+ } else if (i+1 > lastClkBit + *clock + tol + fc){
+ lastClkBit += *clock; //no phase shift but clock bit
+ dest[numBits++] = curPhase;
+ }
+ avgWaveVal = 0;
+ waveStart = i+1;
+ }
+ }
+ avgWaveVal += dest[i+1];
+ }
+ *size = numBits;
+ return errCnt;
+}
+
+//by marshmellow
+//attempt to identify a Sequence Terminator in ASK modulated raw wave
+bool DetectST(uint8_t buffer[], size_t *size, int *foundclock) {
+ size_t bufsize = *size;
+ //need to loop through all samples and identify our clock, look for the ST pattern
+ uint8_t fndClk[] = {8,16,32,40,50,64,128};
+ int clk = 0;
+ int tol = 0;
+ int i, j, skip, start, end, low, high, minClk, waveStart;
+ bool complete = false;
+ int tmpbuff[bufsize / 64];
+ int waveLen[bufsize / 64];
+ size_t testsize = (bufsize < 512) ? bufsize : 512;
+ int phaseoff = 0;
+ high = low = 128;
+ memset(tmpbuff, 0, sizeof(tmpbuff));
+
+ if ( getHiLo(buffer, testsize, &high, &low, 80, 80) == -1 ) {
+ if (g_debugMode==2) prnt("DEBUG STT: just noise detected - quitting");
+ return false; //just noise
+ }
+ i = 0;
+ j = 0;
+ minClk = 255;
+ // get to first full low to prime loop and skip incomplete first pulse
+ while ((buffer[i] < high) && (i < bufsize))
+ ++i;
+ while ((buffer[i] > low) && (i < bufsize))
+ ++i;
+ skip = i;
+
+ // populate tmpbuff buffer with pulse lengths
+ while (i < bufsize) {
+ // measure from low to low
+ while ((buffer[i] > low) && (i < bufsize))
+ ++i;
+ start= i;
+ while ((buffer[i] < high) && (i < bufsize))
+ ++i;
+ //first high point for this wave
+ waveStart = i;
+ while ((buffer[i] > low) && (i < bufsize))
+ ++i;
+ if (j >= (bufsize/64)) {
+ break;
+ }
+ waveLen[j] = i - waveStart; //first high to first low
+ tmpbuff[j++] = i - start;
+ if (i-start < minClk && i < bufsize) {
+ minClk = i - start;
+ }
+ }
+ // set clock - might be able to get this externally and remove this work...
+ if (!clk) {
+ for (uint8_t clkCnt = 0; clkCnt<7; clkCnt++) {
+ tol = fndClk[clkCnt]/8;
+ if (minClk >= fndClk[clkCnt]-tol && minClk <= fndClk[clkCnt]+1) {
+ clk=fndClk[clkCnt];
+ break;
+ }
+ }
+ // clock not found - ERROR
+ if (!clk) {
+ if (g_debugMode==2) prnt("DEBUG STT: clock not found - quitting");
+ return false;
+ }
+ } else tol = clk/8;
+
+ *foundclock = clk;
+
+ // look for Sequence Terminator - should be pulses of clk*(1 or 1.5), clk*2, clk*(1.5 or 2)
+ start = -1;
+ for (i = 0; i < j - 4; ++i) {
+ skip += tmpbuff[i];
+ if (tmpbuff[i] >= clk*1-tol && tmpbuff[i] <= (clk*2)+tol && waveLen[i] < clk+tol) { //1 to 2 clocks depending on 2 bits prior
+ if (tmpbuff[i+1] >= clk*2-tol && tmpbuff[i+1] <= clk*2+tol && waveLen[i+1] > clk*3/2-tol) { //2 clocks and wave size is 1 1/2
+ if (tmpbuff[i+2] >= (clk*3)/2-tol && tmpbuff[i+2] <= clk*2+tol && waveLen[i+2] > clk-tol) { //1 1/2 to 2 clocks and at least one full clock wave
+ if (tmpbuff[i+3] >= clk*1-tol && tmpbuff[i+3] <= clk*2+tol) { //1 to 2 clocks for end of ST + first bit
+ start = i + 3;
+ break;
+ }
+ }
+ }
+ }
+ }
+ // first ST not found - ERROR
+ if (start < 0) {
+ if (g_debugMode==2) prnt("DEBUG STT: first STT not found - quitting");
+ return false;
+ }
+ if (waveLen[i+2] > clk*1+tol)
+ phaseoff = 0;
+ else
+ phaseoff = clk/2;
+
+ // skip over the remainder of ST
+ skip += clk*7/2; //3.5 clocks from tmpbuff[i] = end of st - also aligns for ending point
+
+ // now do it again to find the end
+ end = skip;
+ for (i += 3; i < j - 4; ++i) {
+ end += tmpbuff[i];
+ if (tmpbuff[i] >= clk*1-tol && tmpbuff[i] <= (clk*2)+tol) { //1 to 2 clocks depending on 2 bits prior
+ if (tmpbuff[i+1] >= clk*2-tol && tmpbuff[i+1] <= clk*2+tol && waveLen[i+1] > clk*3/2-tol) { //2 clocks and wave size is 1 1/2
+ if (tmpbuff[i+2] >= (clk*3)/2-tol && tmpbuff[i+2] <= clk*2+tol && waveLen[i+2] > clk-tol) { //1 1/2 to 2 clocks and at least one full clock wave
+ if (tmpbuff[i+3] >= clk*1-tol && tmpbuff[i+3] <= clk*2+tol) { //1 to 2 clocks for end of ST + first bit
+ complete = true;
+ break;
+ }
+ }
+ }
+ }
+ }
+ end -= phaseoff;
+ //didn't find second ST - ERROR
+ if (!complete) {
+ if (g_debugMode==2) prnt("DEBUG STT: second STT not found - quitting");
+ return false;
+ }
+ if (g_debugMode==2) prnt("DEBUG STT: start of data: %d end of data: %d, datalen: %d, clk: %d, bits: %d, phaseoff: %d", skip, end, end-skip, clk, (end-skip)/clk, phaseoff);
+ //now begin to trim out ST so we can use normal demod cmds
+ start = skip;
+ size_t datalen = end - start;
+ // check validity of datalen (should be even clock increments) - use a tolerance of up to 1/8th a clock
+ if (datalen % clk > clk/8) {
+ if (g_debugMode==2) prnt("DEBUG STT: datalen not divisible by clk: %u %% %d = %d - quitting", datalen, clk, datalen % clk);
+ return false;
+ } else {
+ // padd the amount off - could be problematic... but shouldn't happen often
+ datalen += datalen % clk;
+ }
+ // if datalen is less than one t55xx block - ERROR
+ if (datalen/clk < 8*4) {
+ if (g_debugMode==2) prnt("DEBUG STT: datalen is less than 1 full t55xx block - quitting");
+ return false;
+ }
+ size_t dataloc = start;
+ size_t newloc = 0;
+ i=0;
+ // warning - overwriting buffer given with raw wave data with ST removed...
+ while ( dataloc < bufsize-(clk/2) ) {
+ //compensate for long high at end of ST not being high due to signal loss... (and we cut out the start of wave high part)
+ if (buffer[dataloc]<high && buffer[dataloc]>low && buffer[dataloc+3]<high && buffer[dataloc+3]>low) {
+ for(i=0; i < clk/2-tol; ++i) {
+ buffer[dataloc+i] = high+5;
+ }
+ }
+ for (i=0; i<datalen; ++i) {
+ if (i+newloc < bufsize) {
+ if (i+newloc < dataloc)
+ buffer[i+newloc] = buffer[dataloc];
+
+ dataloc++;
+ }
+ }
+ newloc += i;
+ //skip next ST - we just assume it will be there from now on...
+ dataloc += clk*4;
+ }
+ *size = newloc;
+ return true;
projects / proxmark3-svn / blobdiff