// Edits by Gerhard de Koning Gans, Sep 2007 (##)
//-----------------------------------------------------------------------------
-
#include <proxmark3.h>
#include <stdlib.h>
#include "apps.h"
#include "LCD.h"
#endif
-// The large multi-purpose buffer, typically used to hold A/D samples,
-// maybe pre-processed in some way.
-DWORD BigBuf[16000];
-int usbattached = 0;
//=============================================================================
// A buffer where we can queue things up to be sent through the FPGA, for
int ToSendMax;
static int ToSendBit;
-
void BufferClear(void)
{
memset(BigBuf,0,sizeof(BigBuf));
void DbpString(char *str)
{
/* this holds up stuff unless we're connected to usb */
-// if (!usbattached)
-// return;
+ if (!UsbConnected())
+ return;
UsbCommand c;
c.cmd = CMD_DEBUG_PRINT_STRING;
void DbpIntegers(int x1, int x2, int x3)
{
/* this holds up stuff unless we're connected to usb */
-// if (!usbattached)
-// return;
+ if (!UsbConnected())
+ return;
UsbCommand c;
c.cmd = CMD_DEBUG_PRINT_INTEGERS;
SpinDelay(50);
}
-void AcquireRawAdcSamples125k(BOOL at134khz)
-{
- if(at134khz) {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- } else {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- }
-
- // Connect the A/D to the peak-detected low-frequency path.
- SetAdcMuxFor(GPIO_MUXSEL_LOPKD);
-
- // Give it a bit of time for the resonant antenna to settle.
- SpinDelay(50);
-
- // Now set up the SSC to get the ADC samples that are now streaming at us.
- FpgaSetupSsc();
-
- // Now call the acquisition routine
- DoAcquisition125k(at134khz);
-}
-
-// split into two routines so we can avoid timing issues after sending commands //
-void DoAcquisition125k(BOOL at134khz)
-{
- BYTE *dest = (BYTE *)BigBuf;
- int n = sizeof(BigBuf);
- int i;
-
- memset(dest,0,n);
- i = 0;
- for(;;) {
- if(SSC_STATUS & (SSC_STATUS_TX_READY)) {
- SSC_TRANSMIT_HOLDING = 0x43;
- LED_D_ON();
- }
- if(SSC_STATUS & (SSC_STATUS_RX_READY)) {
- dest[i] = (BYTE)SSC_RECEIVE_HOLDING;
- i++;
- LED_D_OFF();
- if(i >= n) {
- break;
- }
- }
- }
- DbpIntegers(dest[0], dest[1], at134khz);
-}
-
-void ModThenAcquireRawAdcSamples125k(int delay_off,int period_0,int period_1,BYTE *command)
-{
- BOOL at134khz;
-
- // see if 'h' was specified
- if(command[strlen((char *) command) - 1] == 'h')
- at134khz= TRUE;
- else
- at134khz= FALSE;
-
- if(at134khz) {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- } else {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- }
-
- // Give it a bit of time for the resonant antenna to settle.
- SpinDelay(50);
-
- // Now set up the SSC to get the ADC samples that are now streaming at us.
- FpgaSetupSsc();
-
- // now modulate the reader field
- while(*command != '\0' && *command != ' ')
- {
- FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
- LED_D_OFF();
- SpinDelayUs(delay_off);
- if(at134khz) {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- } else {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- }
- LED_D_ON();
- if(*(command++) == '0')
- SpinDelayUs(period_0);
- else
- SpinDelayUs(period_1);
- }
- FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
- LED_D_OFF();
- SpinDelayUs(delay_off);
- if(at134khz) {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- } else {
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
- }
-
- // now do the read
- DoAcquisition125k(at134khz);
-}
-
-void AcquireTiType(void)
-{
- int i;
- int n = 5000;
-
- // clear buffer
- memset(BigBuf,0,sizeof(BigBuf));
-
- // Set up the synchronous serial port
- PIO_DISABLE = (1<<GPIO_SSC_DIN);
- PIO_PERIPHERAL_A_SEL = (1<<GPIO_SSC_DIN);
-
- // steal this pin from the SSP and use it to control the modulation
- PIO_ENABLE = (1<<GPIO_SSC_DOUT);
- PIO_OUTPUT_ENABLE = (1<<GPIO_SSC_DOUT);
-
- SSC_CONTROL = SSC_CONTROL_RESET;
- SSC_CONTROL = SSC_CONTROL_RX_ENABLE | SSC_CONTROL_TX_ENABLE;
-
- // Sample at 2 Mbit/s, so TI tags are 16.2 vs. 14.9 clocks long
- // 48/2 = 24 MHz clock must be divided by 12
- SSC_CLOCK_DIVISOR = 12;
-
- SSC_RECEIVE_CLOCK_MODE = SSC_CLOCK_MODE_SELECT(0);
- SSC_RECEIVE_FRAME_MODE = SSC_FRAME_MODE_BITS_IN_WORD(32) | SSC_FRAME_MODE_MSB_FIRST;
- SSC_TRANSMIT_CLOCK_MODE = 0;
- SSC_TRANSMIT_FRAME_MODE = 0;
-
- LED_D_ON();
-
- // modulate antenna
- PIO_OUTPUT_DATA_SET = (1<<GPIO_SSC_DOUT);
-
- // Charge TI tag for 50ms.
- SpinDelay(50);
-
- // stop modulating antenna and listen
- PIO_OUTPUT_DATA_CLEAR = (1<<GPIO_SSC_DOUT);
-
- LED_D_OFF();
-
- i = 0;
- for(;;) {
- if(SSC_STATUS & SSC_STATUS_RX_READY) {
- BigBuf[i] = SSC_RECEIVE_HOLDING; // store 32 bit values in buffer
- i++; if(i >= n) return;
- }
- WDT_HIT();
- }
-
- // return stolen pin ro SSP
- PIO_DISABLE = (1<<GPIO_SSC_DOUT);
- PIO_PERIPHERAL_A_SEL = (1<<GPIO_SSC_DIN) | (1<<GPIO_SSC_DOUT);
-}
-
-void AcquireRawBitsTI(void)
-{
- LED_D_ON();
- // TI tags charge at 134.2Khz
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz
- // Place FPGA in passthrough mode, in this mode the CROSS_LO line
- // connects to SSP_DIN and the SSP_DOUT logic level controls
- // whether we're modulating the antenna (high)
- // or listening to the antenna (low)
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_PASSTHRU);
-
- // get TI tag data into the buffer
- AcquireTiType();
-
- FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-}
-
//-----------------------------------------------------------------------------
// Read an ADC channel and block till it completes, then return the result
// in ADC units (0 to 1023). Also a routine to average 32 samples and
UsbSendPacket((BYTE *)&c, sizeof(c));
}
-void SimulateTagLowFrequency(int period, int ledcontrol)
-{
- int i;
- BYTE *tab = (BYTE *)BigBuf;
-
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_SIMULATOR);
-
- PIO_ENABLE = (1 << GPIO_SSC_DOUT) | (1 << GPIO_SSC_CLK);
-
- PIO_OUTPUT_ENABLE = (1 << GPIO_SSC_DOUT);
- PIO_OUTPUT_DISABLE = (1 << GPIO_SSC_CLK);
-
-#define SHORT_COIL() LOW(GPIO_SSC_DOUT)
-#define OPEN_COIL() HIGH(GPIO_SSC_DOUT)
-
- i = 0;
- for(;;) {
- while(!(PIO_PIN_DATA_STATUS & (1<<GPIO_SSC_CLK))) {
- if(BUTTON_PRESS()) {
- DbpString("Stopped");
- return;
- }
- WDT_HIT();
- }
-
- if (ledcontrol)
- LED_D_ON();
-
- if(tab[i])
- OPEN_COIL();
- else
- SHORT_COIL();
-
- if (ledcontrol)
- LED_D_OFF();
-
- while(PIO_PIN_DATA_STATUS & (1<<GPIO_SSC_CLK)) {
- if(BUTTON_PRESS()) {
- DbpString("Stopped");
- return;
- }
- WDT_HIT();
- }
-
- i++;
- if(i == period) i = 0;
- }
-}
-
-// compose fc/8 fc/10 waveform
-static void fc(int c, int *n) {
- BYTE *dest = (BYTE *)BigBuf;
- int idx;
-
- // for when we want an fc8 pattern every 4 logical bits
- if(c==0) {
- dest[((*n)++)]=1;
- dest[((*n)++)]=1;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- }
- // an fc/8 encoded bit is a bit pattern of 11000000 x6 = 48 samples
- if(c==8) {
- for (idx=0; idx<6; idx++) {
- dest[((*n)++)]=1;
- dest[((*n)++)]=1;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- }
- }
-
- // an fc/10 encoded bit is a bit pattern of 1110000000 x5 = 50 samples
- if(c==10) {
- for (idx=0; idx<5; idx++) {
- dest[((*n)++)]=1;
- dest[((*n)++)]=1;
- dest[((*n)++)]=1;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- dest[((*n)++)]=0;
- }
- }
-}
-
-// prepare a waveform pattern in the buffer based on the ID given then
-// simulate a HID tag until the button is pressed
-static void CmdHIDsimTAG(int hi, int lo, int ledcontrol)
-{
- int n=0, i=0;
- /*
- HID tag bitstream format
- The tag contains a 44bit unique code. This is sent out MSB first in sets of 4 bits
- A 1 bit is represented as 6 fc8 and 5 fc10 patterns
- A 0 bit is represented as 5 fc10 and 6 fc8 patterns
- A fc8 is inserted before every 4 bits
- A special start of frame pattern is used consisting a0b0 where a and b are neither 0
- nor 1 bits, they are special patterns (a = set of 12 fc8 and b = set of 10 fc10)
- */
-
- if (hi>0xFFF) {
- DbpString("Tags can only have 44 bits.");
- return;
- }
- fc(0,&n);
- // special start of frame marker containing invalid bit sequences
- fc(8, &n); fc(8, &n); // invalid
- fc(8, &n); fc(10, &n); // logical 0
- fc(10, &n); fc(10, &n); // invalid
- fc(8, &n); fc(10, &n); // logical 0
-
- WDT_HIT();
- // manchester encode bits 43 to 32
- for (i=11; i>=0; i--) {
- if ((i%4)==3) fc(0,&n);
- if ((hi>>i)&1) {
- fc(10, &n); fc(8, &n); // low-high transition
- } else {
- fc(8, &n); fc(10, &n); // high-low transition
- }
- }
-
- WDT_HIT();
- // manchester encode bits 31 to 0
- for (i=31; i>=0; i--) {
- if ((i%4)==3) fc(0,&n);
- if ((lo>>i)&1) {
- fc(10, &n); fc(8, &n); // low-high transition
- } else {
- fc(8, &n); fc(10, &n); // high-low transition
- }
- }
-
- if (ledcontrol)
- LED_A_ON();
- SimulateTagLowFrequency(n, ledcontrol);
-
- if (ledcontrol)
- LED_A_OFF();
-}
-
-// loop to capture raw HID waveform then FSK demodulate the TAG ID from it
-static void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol)
-{
- BYTE *dest = (BYTE *)BigBuf;
- int m=0, n=0, i=0, idx=0, found=0, lastval=0;
- DWORD hi=0, lo=0;
-
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
-
- // Connect the A/D to the peak-detected low-frequency path.
- SetAdcMuxFor(GPIO_MUXSEL_LOPKD);
-
- // Give it a bit of time for the resonant antenna to settle.
- SpinDelay(50);
-
- // Now set up the SSC to get the ADC samples that are now streaming at us.
- FpgaSetupSsc();
-
- for(;;) {
- WDT_HIT();
- if (ledcontrol)
- LED_A_ON();
- if(BUTTON_PRESS()) {
- DbpString("Stopped");
- if (ledcontrol)
- LED_A_OFF();
- return;
- }
-
- i = 0;
- m = sizeof(BigBuf);
- memset(dest,128,m);
- for(;;) {
- if(SSC_STATUS & (SSC_STATUS_TX_READY)) {
- SSC_TRANSMIT_HOLDING = 0x43;
- if (ledcontrol)
- LED_D_ON();
- }
- if(SSC_STATUS & (SSC_STATUS_RX_READY)) {
- dest[i] = (BYTE)SSC_RECEIVE_HOLDING;
- // we don't care about actual value, only if it's more or less than a
- // threshold essentially we capture zero crossings for later analysis
- if(dest[i] < 127) dest[i] = 0; else dest[i] = 1;
- i++;
- if (ledcontrol)
- LED_D_OFF();
- if(i >= m) {
- break;
- }
- }
- }
-
- // FSK demodulator
-
- // sync to first lo-hi transition
- for( idx=1; idx<m; idx++) {
- if (dest[idx-1]<dest[idx])
- lastval=idx;
- break;
- }
- WDT_HIT();
-
- // count cycles between consecutive lo-hi transitions, there should be either 8 (fc/8)
- // or 10 (fc/10) cycles but in practice due to noise etc we may end up with with anywhere
- // between 7 to 11 cycles so fuzz it by treat anything <9 as 8 and anything else as 10
- for( i=0; idx<m; idx++) {
- if (dest[idx-1]<dest[idx]) {
- dest[i]=idx-lastval;
- if (dest[i] <= 8) {
- dest[i]=1;
- } else {
- dest[i]=0;
- }
-
- lastval=idx;
- i++;
- }
- }
- m=i;
- WDT_HIT();
-
- // we now have a set of cycle counts, loop over previous results and aggregate data into bit patterns
- lastval=dest[0];
- idx=0;
- i=0;
- n=0;
- for( idx=0; idx<m; idx++) {
- if (dest[idx]==lastval) {
- n++;
- } else {
- // a bit time is five fc/10 or six fc/8 cycles so figure out how many bits a pattern width represents,
- // an extra fc/8 pattern preceeds every 4 bits (about 200 cycles) just to complicate things but it gets
- // swallowed up by rounding
- // expected results are 1 or 2 bits, any more and it's an invalid manchester encoding
- // special start of frame markers use invalid manchester states (no transitions) by using sequences
- // like 111000
- if (dest[idx-1]) {
- n=(n+1)/6; // fc/8 in sets of 6
- } else {
- n=(n+1)/5; // fc/10 in sets of 5
- }
- switch (n) { // stuff appropriate bits in buffer
- case 0:
- case 1: // one bit
- dest[i++]=dest[idx-1];
- break;
- case 2: // two bits
- dest[i++]=dest[idx-1];
- dest[i++]=dest[idx-1];
- break;
- case 3: // 3 bit start of frame markers
- dest[i++]=dest[idx-1];
- dest[i++]=dest[idx-1];
- dest[i++]=dest[idx-1];
- break;
- // When a logic 0 is immediately followed by the start of the next transmisson
- // (special pattern) a pattern of 4 bit duration lengths is created.
- case 4:
- dest[i++]=dest[idx-1];
- dest[i++]=dest[idx-1];
- dest[i++]=dest[idx-1];
- dest[i++]=dest[idx-1];
- break;
- default: // this shouldn't happen, don't stuff any bits
- break;
- }
- n=0;
- lastval=dest[idx];
- }
- }
- m=i;
- WDT_HIT();
-
- // final loop, go over previously decoded manchester data and decode into usable tag ID
- // 111000 bit pattern represent start of frame, 01 pattern represents a 1 and 10 represents a 0
- for( idx=0; idx<m-6; idx++) {
- // search for a start of frame marker
- if ( dest[idx] && dest[idx+1] && dest[idx+2] && (!dest[idx+3]) && (!dest[idx+4]) && (!dest[idx+5]) )
- {
- found=1;
- idx+=6;
- if (found && (hi|lo)) {
- DbpString("TAG ID");
- DbpIntegers(hi, lo, (lo>>1)&0xffff);
- /* if we're only looking for one tag */
- if (findone)
- {
- *high = hi;
- *low = lo;
- return;
- }
- hi=0;
- lo=0;
- found=0;
- }
- }
- if (found) {
- if (dest[idx] && (!dest[idx+1]) ) {
- hi=(hi<<1)|(lo>>31);
- lo=(lo<<1)|0;
- } else if ( (!dest[idx]) && dest[idx+1]) {
- hi=(hi<<1)|(lo>>31);
- lo=(lo<<1)|1;
- } else {
- found=0;
- hi=0;
- lo=0;
- }
- idx++;
- }
- if ( dest[idx] && dest[idx+1] && dest[idx+2] && (!dest[idx+3]) && (!dest[idx+4]) && (!dest[idx+5]) )
- {
- found=1;
- idx+=6;
- if (found && (hi|lo)) {
- DbpString("TAG ID");
- DbpIntegers(hi, lo, (lo>>1)&0xffff);
- /* if we're only looking for one tag */
- if (findone)
- {
- *high = hi;
- *low = lo;
- return;
- }
- hi=0;
- lo=0;
- found=0;
- }
- }
- }
- WDT_HIT();
- }
-}
-
void SimulateTagHfListen(void)
{
BYTE *dest = (BYTE *)BigBuf;
DbpString("simulate tag (now type bitsamples)");
}
-void UsbPacketReceived(BYTE *packet, int len)
+void ReadMem(int addr)
{
- UsbCommand *c = (UsbCommand *)packet;
-
- switch(c->cmd) {
- case CMD_ACQUIRE_RAW_ADC_SAMPLES_125K:
- AcquireRawAdcSamples125k(c->ext1);
- break;
-
- case CMD_MOD_THEN_ACQUIRE_RAW_ADC_SAMPLES_125K:
- ModThenAcquireRawAdcSamples125k(c->ext1,c->ext2,c->ext3,c->d.asBytes);
- break;
+ const DWORD *data = ((DWORD *)addr);
+ int i;
- case CMD_ACQUIRE_RAW_BITS_TI_TYPE:
- AcquireRawBitsTI();
- break;
+ DbpString("Reading memory at address");
+ DbpIntegers(0, 0, addr);
+ for (i = 0; i < 8; i+= 2)
+ DbpIntegers(0, data[i], data[i+1]);
+}
- case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_15693:
- AcquireRawAdcSamplesIso15693();
- break;
+/* osimage version information is linked in */
+extern struct version_information version_information;
+/* bootrom version information is pointed to from _bootphase1_version_pointer */
+extern char _bootphase1_version_pointer, _flash_start, _flash_end;
+void SendVersion(void)
+{
+ char temp[48]; /* Limited data payload in USB packets */
+ DbpString("Prox/RFID mark3 RFID instrument");
+
+ /* Try to find the bootrom version information. Expect to find a pointer at
+ * symbol _bootphase1_version_pointer, perform slight sanity checks on the
+ * pointer, then use it.
+ */
+ void *bootrom_version = *(void**)&_bootphase1_version_pointer;
+ if( bootrom_version < (void*)&_flash_start || bootrom_version >= (void*)&_flash_end ) {
+ DbpString("bootrom version information appears invalid");
+ } else {
+ FormatVersionInformation(temp, sizeof(temp), "bootrom: ", bootrom_version);
+ DbpString(temp);
+ }
+
+ FormatVersionInformation(temp, sizeof(temp), "os: ", &version_information);
+ DbpString(temp);
+
+ FpgaGatherVersion(temp, sizeof(temp));
+ DbpString(temp);
+}
- case CMD_BUFF_CLEAR:
- BufferClear();
- break;
+// samy's sniff and repeat routine
+void SamyRun()
+{
+ DbpString("Stand-alone mode! No PC necessary.");
- case CMD_READER_ISO_15693:
- ReaderIso15693(c->ext1);
- break;
+ // 3 possible options? no just 2 for now
+#define OPTS 2
- case CMD_SIMTAG_ISO_15693:
- SimTagIso15693(c->ext1);
- break;
+ int high[OPTS], low[OPTS];
- case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_14443:
- AcquireRawAdcSamplesIso14443(c->ext1);
- break;
+ // Oooh pretty -- notify user we're in elite samy mode now
+ LED(LED_RED, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_GREEN, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_RED, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_GREEN, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_RED, 200);
- case CMD_READ_SRI512_TAG:
- ReadSRI512Iso14443(c->ext1);
- break;
+ int selected = 0;
+ int playing = 0;
- case CMD_READER_ISO_14443a:
- ReaderIso14443a(c->ext1);
- break;
+ // Turn on selected LED
+ LED(selected + 1, 0);
- case CMD_SNOOP_ISO_14443:
- SnoopIso14443();
- break;
+ for (;;)
+ {
+ UsbPoll(FALSE);
+ WDT_HIT();
- case CMD_SNOOP_ISO_14443a:
- SnoopIso14443a();
- break;
+ // Was our button held down or pressed?
+ int button_pressed = BUTTON_HELD(1000);
+ SpinDelay(300);
+
+ // Button was held for a second, begin recording
+ if (button_pressed > 0)
+ {
+ LEDsoff();
+ LED(selected + 1, 0);
+ LED(LED_RED2, 0);
+
+ // record
+ DbpString("Starting recording");
+
+ // wait for button to be released
+ while(BUTTON_PRESS())
+ WDT_HIT();
+
+ /* need this delay to prevent catching some weird data */
+ SpinDelay(500);
+
+ CmdHIDdemodFSK(1, &high[selected], &low[selected], 0);
+ DbpString("Recorded");
+ DbpIntegers(selected, high[selected], low[selected]);
+
+ LEDsoff();
+ LED(selected + 1, 0);
+ // Finished recording
+
+ // If we were previously playing, set playing off
+ // so next button push begins playing what we recorded
+ playing = 0;
+ }
+
+ // Change where to record (or begin playing)
+ else if (button_pressed)
+ {
+ // Next option if we were previously playing
+ if (playing)
+ selected = (selected + 1) % OPTS;
+ playing = !playing;
+
+ LEDsoff();
+ LED(selected + 1, 0);
+
+ // Begin transmitting
+ if (playing)
+ {
+ LED(LED_GREEN, 0);
+ DbpString("Playing");
+ // wait for button to be released
+ while(BUTTON_PRESS())
+ WDT_HIT();
+ DbpIntegers(selected, high[selected], low[selected]);
+ CmdHIDsimTAG(high[selected], low[selected], 0);
+ DbpString("Done playing");
+ if (BUTTON_HELD(1000) > 0)
+ {
+ DbpString("Exiting");
+ LEDsoff();
+ return;
+ }
+
+ /* We pressed a button so ignore it here with a delay */
+ SpinDelay(300);
+
+ // when done, we're done playing, move to next option
+ selected = (selected + 1) % OPTS;
+ playing = !playing;
+ LEDsoff();
+ LED(selected + 1, 0);
+ }
+ else
+ while(BUTTON_PRESS())
+ WDT_HIT();
+ }
+ }
+}
+
+
+/*
+OBJECTIVE
+Listen and detect an external reader. Determine the best location
+for the antenna.
+
+INSTRUCTIONS:
+Inside the ListenReaderField() function, there is two mode.
+By default, when you call the function, you will enter mode 1.
+If you press the PM3 button one time, you will enter mode 2.
+If you press the PM3 button a second time, you will exit the function.
+
+DESCRIPTION OF MODE 1:
+This mode just listens for an external reader field and lights up green
+for HF and/or red for LF. This is the original mode of the detectreader
+function.
+
+DESCRIPTION OF MODE 2:
+This mode will visually represent, using the LEDs, the actual strength of the
+current compared to the maximum current detected. Basically, once you know
+what kind of external reader is present, it will help you spot the best location to place
+your antenna. You will probably not get some good results if there is a LF and a HF reader
+at the same place! :-)
+
+LIGHT SCHEME USED:
+*/
+static const char LIGHT_SCHEME[] = {
+ 0x0, /* ---- | No field detected */
+ 0x1, /* X--- | 14% of maximum current detected */
+ 0x2, /* -X-- | 29% of maximum current detected */
+ 0x4, /* --X- | 43% of maximum current detected */
+ 0x8, /* ---X | 57% of maximum current detected */
+ 0xC, /* --XX | 71% of maximum current detected */
+ 0xE, /* -XXX | 86% of maximum current detected */
+ 0xF, /* XXXX | 100% of maximum current detected */
+};
+static const int LIGHT_LEN = sizeof(LIGHT_SCHEME)/sizeof(LIGHT_SCHEME[0]);
+
+void ListenReaderField(int limit)
+{
+ int lf_av, lf_av_new, lf_baseline= 0, lf_count= 0, lf_max;
+ int hf_av, hf_av_new, hf_baseline= 0, hf_count= 0, hf_max;
+ int mode=1, display_val, display_max, i;
+
+#define LF_ONLY 1
+#define HF_ONLY 2
+
+ LEDsoff();
+
+ lf_av=lf_max=ReadAdc(ADC_CHAN_LF);
+
+ if(limit != HF_ONLY) {
+ DbpString("LF 125/134 Baseline:");
+ DbpIntegers(lf_av,0,0);
+ lf_baseline= lf_av;
+ }
+
+ hf_av=hf_max=ReadAdc(ADC_CHAN_HF);
+
+ if (limit != LF_ONLY) {
+ DbpString("HF 13.56 Baseline:");
+ DbpIntegers(hf_av,0,0);
+ hf_baseline= hf_av;
+ }
+
+ for(;;) {
+ if (BUTTON_PRESS()) {
+ SpinDelay(500);
+ switch (mode) {
+ case 1:
+ mode=2;
+ DbpString("Signal Strength Mode");
+ break;
+ case 2:
+ default:
+ DbpString("Stopped");
+ LEDsoff();
+ return;
+ break;
+ }
+ }
+ WDT_HIT();
+
+ if (limit != HF_ONLY) {
+ if(mode==1) {
+ if (abs(lf_av - lf_baseline) > 10) LED_D_ON();
+ else LED_D_OFF();
+ }
+
+ ++lf_count;
+ lf_av_new= ReadAdc(ADC_CHAN_LF);
+ // see if there's a significant change
+ if(abs(lf_av - lf_av_new) > 10) {
+ DbpString("LF 125/134 Field Change:");
+ DbpIntegers(lf_av,lf_av_new,lf_count);
+ lf_av= lf_av_new;
+ if (lf_av > lf_max)
+ lf_max = lf_av;
+ lf_count= 0;
+ }
+ }
+
+ if (limit != LF_ONLY) {
+ if (mode == 1){
+ if (abs(hf_av - hf_baseline) > 10) LED_B_ON();
+ else LED_B_OFF();
+ }
+
+ ++hf_count;
+ hf_av_new= ReadAdc(ADC_CHAN_HF);
+ // see if there's a significant change
+ if(abs(hf_av - hf_av_new) > 10) {
+ DbpString("HF 13.56 Field Change:");
+ DbpIntegers(hf_av,hf_av_new,hf_count);
+ hf_av= hf_av_new;
+ if (hf_av > hf_max)
+ hf_max = hf_av;
+ hf_count= 0;
+ }
+ }
+
+ if(mode == 2) {
+ if (limit == LF_ONLY) {
+ display_val = lf_av;
+ display_max = lf_max;
+ } else if (limit == HF_ONLY) {
+ display_val = hf_av;
+ display_max = hf_max;
+ } else { /* Pick one at random */
+ if( (hf_max - hf_baseline) > (lf_max - lf_baseline) ) {
+ display_val = hf_av;
+ display_max = hf_max;
+ } else {
+ display_val = lf_av;
+ display_max = lf_max;
+ }
+ }
+ for (i=0; i<LIGHT_LEN; i++) {
+ if (display_val >= ((display_max/LIGHT_LEN)*i) && display_val <= ((display_max/LIGHT_LEN)*(i+1))) {
+ if (LIGHT_SCHEME[i] & 0x1) LED_C_ON(); else LED_C_OFF();
+ if (LIGHT_SCHEME[i] & 0x2) LED_A_ON(); else LED_A_OFF();
+ if (LIGHT_SCHEME[i] & 0x4) LED_B_ON(); else LED_B_OFF();
+ if (LIGHT_SCHEME[i] & 0x8) LED_D_ON(); else LED_D_OFF();
+ break;
+ }
+ }
+ }
+ }
+}
+
+void UsbPacketReceived(BYTE *packet, int len)
+{
+ UsbCommand *c = (UsbCommand *)packet;
+
+ switch(c->cmd) {
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_125K:
+ AcquireRawAdcSamples125k(c->ext1);
+ break;
+
+ case CMD_MOD_THEN_ACQUIRE_RAW_ADC_SAMPLES_125K:
+ ModThenAcquireRawAdcSamples125k(c->ext1,c->ext2,c->ext3,c->d.asBytes);
+ break;
+
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_15693:
+ AcquireRawAdcSamplesIso15693();
+ break;
+
+ case CMD_BUFF_CLEAR:
+ BufferClear();
+ break;
+
+ case CMD_READER_ISO_15693:
+ ReaderIso15693(c->ext1);
+ break;
+
+ case CMD_SIMTAG_ISO_15693:
+ SimTagIso15693(c->ext1);
+ break;
+
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_14443:
+ AcquireRawAdcSamplesIso14443(c->ext1);
+ break;
+
+ case CMD_READ_SRI512_TAG:
+ ReadSRI512Iso14443(c->ext1);
+ break;
+
+ case CMD_READER_ISO_14443a:
+ ReaderIso14443a(c->ext1);
+ break;
+
+ case CMD_SNOOP_ISO_14443:
+ SnoopIso14443();
+ break;
+
+ case CMD_SNOOP_ISO_14443a:
+ SnoopIso14443a();
+ break;
case CMD_SIMULATE_TAG_HF_LISTEN:
SimulateTagHfListen();
LED_D_OFF(); // LED D indicates field ON or OFF
break;
- case CMD_DOWNLOAD_RAW_ADC_SAMPLES_125K:
- case CMD_DOWNLOAD_RAW_BITS_TI_TYPE: {
+ case CMD_READ_TI_TYPE:
+ ReadTItag();
+ break;
+
+ case CMD_WRITE_TI_TYPE:
+ WriteTItag(c->ext1,c->ext2,c->ext3);
+ break;
+
+ case CMD_DOWNLOAD_RAW_ADC_SAMPLES_125K: {
UsbCommand n;
if(c->cmd == CMD_DOWNLOAD_RAW_ADC_SAMPLES_125K) {
n.cmd = CMD_DOWNLOADED_RAW_ADC_SAMPLES_125K;
SimulateTagLowFrequency(c->ext1, 1);
LED_A_OFF();
break;
-#ifdef WITH_LCD
- case CMD_LCD_RESET:
- LCDReset();
- break;
-#endif
case CMD_READ_MEM:
ReadMem(c->ext1);
break;
case CMD_SET_LF_DIVISOR:
FpgaSendCommand(FPGA_CMD_SET_DIVISOR, c->ext1);
break;
+ case CMD_VERSION:
+ SendVersion();
+ break;
+ case CMD_LF_SIMULATE_BIDIR:
+ SimulateTagLowFrequencyBidir(c->ext1, c->ext2);
+ break;
#ifdef WITH_LCD
+ case CMD_LCD_RESET:
+ LCDReset();
+ break;
case CMD_LCD:
LCDSend(c->ext1);
break;
#endif
- case CMD_SETUP_WRITE:
+ case CMD_SETUP_WRITE:
case CMD_FINISH_WRITE:
case CMD_HARDWARE_RESET:
USB_D_PLUS_PULLUP_OFF();
}
break;
-
default:
DbpString("unknown command");
break;
}
}
-void ReadMem(int addr)
-{
- const DWORD *data = ((DWORD *)addr);
- int i;
-
- DbpString("Reading memory at address");
- DbpIntegers(0, 0, addr);
- for (i = 0; i < 8; i+= 2)
- DbpIntegers(0, data[i], data[i+1]);
-}
-
void AppMain(void)
{
memset(BigBuf,0,sizeof(BigBuf));
#endif
for(;;) {
- usbattached = UsbPoll(FALSE);
+ UsbPoll(FALSE);
WDT_HIT();
if (BUTTON_HELD(1000) > 0)
SamyRun();
}
}
-
-
-// samy's sniff and repeat routine
-void SamyRun()
-{
- DbpString("Stand-alone mode! No PC necessary.");
-
- // 3 possible options? no just 2 for now
-#define OPTS 2
-
- int high[OPTS], low[OPTS];
-
- // Oooh pretty -- notify user we're in elite samy mode now
- LED(LED_RED, 200);
- LED(LED_ORANGE, 200);
- LED(LED_GREEN, 200);
- LED(LED_ORANGE, 200);
- LED(LED_RED, 200);
- LED(LED_ORANGE, 200);
- LED(LED_GREEN, 200);
- LED(LED_ORANGE, 200);
- LED(LED_RED, 200);
-
- int selected = 0;
- int playing = 0;
-
- // Turn on selected LED
- LED(selected + 1, 0);
-
- for (;;)
- {
- usbattached = UsbPoll(FALSE);
- WDT_HIT();
-
- // Was our button held down or pressed?
- int button_pressed = BUTTON_HELD(1000);
- SpinDelay(300);
-
- // Button was held for a second, begin recording
- if (button_pressed > 0)
- {
- LEDsoff();
- LED(selected + 1, 0);
- LED(LED_RED2, 0);
-
- // record
- DbpString("Starting recording");
-
- // wait for button to be released
- while(BUTTON_PRESS())
- WDT_HIT();
-
- /* need this delay to prevent catching some weird data */
- SpinDelay(500);
-
- CmdHIDdemodFSK(1, &high[selected], &low[selected], 0);
- DbpString("Recorded");
- DbpIntegers(selected, high[selected], low[selected]);
-
- LEDsoff();
- LED(selected + 1, 0);
- // Finished recording
-
- // If we were previously playing, set playing off
- // so next button push begins playing what we recorded
- playing = 0;
- }
-
- // Change where to record (or begin playing)
- else if (button_pressed)
- {
- // Next option if we were previously playing
- if (playing)
- selected = (selected + 1) % OPTS;
- playing = !playing;
-
- LEDsoff();
- LED(selected + 1, 0);
-
- // Begin transmitting
- if (playing)
- {
- LED(LED_GREEN, 0);
- DbpString("Playing");
- // wait for button to be released
- while(BUTTON_PRESS())
- WDT_HIT();
- DbpIntegers(selected, high[selected], low[selected]);
- CmdHIDsimTAG(high[selected], low[selected], 0);
- DbpString("Done playing");
- if (BUTTON_HELD(1000) > 0)
- {
- DbpString("Exiting");
- LEDsoff();
- return;
- }
-
- /* We pressed a button so ignore it here with a delay */
- SpinDelay(300);
-
- // when done, we're done playing, move to next option
- selected = (selected + 1) % OPTS;
- playing = !playing;
- LEDsoff();
- LED(selected + 1, 0);
- }
- else
- while(BUTTON_PRESS())
- WDT_HIT();
- }
- }
-}
-
-
-// listen for external reader
-void ListenReaderField(int limit)
-{
- int lf_av, lf_av_new, lf_baseline= 0, lf_count= 0;
- int hf_av, hf_av_new, hf_baseline= 0, hf_count= 0;
-
-#define LF_ONLY 1
-#define HF_ONLY 2
-
- LED_A_OFF();
- LED_B_OFF();
- LED_C_OFF();
- LED_D_OFF();
-
- lf_av= ReadAdc(ADC_CHAN_LF);
-
- if(limit != HF_ONLY)
- {
- DbpString("LF 125/134 Baseline:");
- DbpIntegers(lf_av,0,0);
- lf_baseline= lf_av;
- }
-
- hf_av= ReadAdc(ADC_CHAN_HF);
-
-
- if (limit != LF_ONLY)
- {
- DbpString("HF 13.56 Baseline:");
- DbpIntegers(hf_av,0,0);
- hf_baseline= hf_av;
- }
-
- for(;;)
- {
- if(BUTTON_PRESS())
- {
- DbpString("Stopped");
- LED_B_OFF();
- LED_D_OFF();
- return;
- }
- WDT_HIT();
-
-
- if (limit != HF_ONLY)
- {
- if (abs(lf_av - lf_baseline) > 10)
- LED_D_ON();
- else
- LED_D_OFF();
- ++lf_count;
- lf_av_new= ReadAdc(ADC_CHAN_LF);
- // see if there's a significant change
- if(abs(lf_av - lf_av_new) > 10)
- {
- DbpString("LF 125/134 Field Change:");
- DbpIntegers(lf_av,lf_av_new,lf_count);
- lf_av= lf_av_new;
- lf_count= 0;
- }
- }
-
- if (limit != LF_ONLY)
- {
- if (abs(hf_av - hf_baseline) > 10)
- LED_B_ON();
- else
- LED_B_OFF();
- ++hf_count;
- hf_av_new= ReadAdc(ADC_CHAN_HF);
- // see if there's a significant change
- if(abs(hf_av - hf_av_new) > 10)
- {
- DbpString("HF 13.56 Field Change:");
- DbpIntegers(hf_av,hf_av_new,hf_count);
- hf_av= hf_av_new;
- hf_count= 0;
- }
- }
- }
-}