- * reads the voltage in the antenna: the result is a graph
- * which should clearly show the resonating frequency of your
- * LF antenna ( hopefully around 90 if it is tuned to 125kHz!)
- */\r
-void SweepLFrange()\r
-{\r
- BYTE *dest = (BYTE *)BigBuf;\r
- int i;\r
-\r
- // clear buffer\r
- memset(BigBuf,0,sizeof(BigBuf));\r
-\r
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);\r
- for (i=255; i>19; i--) {\r
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, i);\r
- SpinDelay(20);\r
- dest[i] = (137500 * AvgAdc(4)) >> 18;\r
- }\r
-}\r
-\r
-void MeasureAntennaTuning(void)\r
-{\r
-// Impedances are Zc = 1/(j*omega*C), in ohms\r
-#define LF_TUNING_CAP_Z 1273 // 1 nF @ 125 kHz\r
-#define HF_TUNING_CAP_Z 235 // 50 pF @ 13.56 MHz\r
-\r
- int vLf125, vLf134, vHf; // in mV\r
-\r
- UsbCommand c;\r
-\r
- // Let the FPGA drive the low-frequency antenna around 125 kHz.\r
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz\r
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER | FPGA_LF_READER_USE_125_KHZ);\r
- SpinDelay(20);\r
- vLf125 = AvgAdc(4);\r
- // Vref = 3.3V, and a 10000:240 voltage divider on the input\r
- // can measure voltages up to 137500 mV\r
- vLf125 = (137500 * vLf125) >> 10;\r
-\r
- // Let the FPGA drive the low-frequency antenna around 134 kHz.\r
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz\r
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER | FPGA_LF_READER_USE_134_KHZ);\r
- SpinDelay(20);\r
- vLf134 = AvgAdc(4);\r
- // Vref = 3.3V, and a 10000:240 voltage divider on the input\r
- // can measure voltages up to 137500 mV\r
- vLf134 = (137500 * vLf134) >> 10;\r
-\r
- // Let the FPGA drive the high-frequency antenna around 13.56 MHz.\r
- FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_READER_RX_XCORR);\r
- SpinDelay(20);\r
- vHf = AvgAdc(5);\r
- // Vref = 3300mV, and an 10:1 voltage divider on the input\r
- // can measure voltages up to 33000 mV\r
- vHf = (33000 * vHf) >> 10;\r
-\r
- c.cmd = CMD_MEASURED_ANTENNA_TUNING;\r
- c.ext1 = (vLf125 << 0) | (vLf134 << 16);\r
- c.ext2 = vHf;\r
- c.ext3 = (LF_TUNING_CAP_Z << 0) | (HF_TUNING_CAP_Z << 16);\r
- UsbSendPacket((BYTE *)&c, sizeof(c));\r
-}\r
-\r
-void SimulateTagLowFrequency(int period)\r
-{\r
- int i;\r
- BYTE *tab = (BYTE *)BigBuf;\r
-\r
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_SIMULATOR);\r
-\r
- PIO_ENABLE = (1 << GPIO_SSC_DOUT) | (1 << GPIO_SSC_CLK);\r
-\r
- PIO_OUTPUT_ENABLE = (1 << GPIO_SSC_DOUT);\r
- PIO_OUTPUT_DISABLE = (1 << GPIO_SSC_CLK);\r
-\r
-#define SHORT_COIL() LOW(GPIO_SSC_DOUT)\r
-#define OPEN_COIL() HIGH(GPIO_SSC_DOUT)\r
-\r
- i = 0;\r
- for(;;) {\r
- while(!(PIO_PIN_DATA_STATUS & (1<<GPIO_SSC_CLK))) {\r
- if(BUTTON_PRESS()) {\r
- return;\r
- }\r
- WDT_HIT();\r
- }\r
-\r
- LED_D_ON();\r
- if(tab[i]) {\r
- OPEN_COIL();\r
- } else {\r
- SHORT_COIL();\r
- }\r
- LED_D_OFF();\r
-\r
- while(PIO_PIN_DATA_STATUS & (1<<GPIO_SSC_CLK)) {\r
- if(BUTTON_PRESS()) {\r
- return;\r
- }\r
- WDT_HIT();\r
- }\r
-\r
- i++;\r
- if(i == period) i = 0;\r
- }\r
-}\r
-\r
-// compose fc/8 fc/10 waveform\r
-static void fc(int c, int *n) {\r
- BYTE *dest = (BYTE *)BigBuf;\r
- int idx;\r
-\r
- // for when we want an fc8 pattern every 4 logical bits\r
- if(c==0) {\r
- dest[((*n)++)]=1;\r
- dest[((*n)++)]=1;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- }\r
- // an fc/8 encoded bit is a bit pattern of 11000000 x6 = 48 samples\r
- if(c==8) {\r
- for (idx=0; idx<6; idx++) {\r
- dest[((*n)++)]=1;\r
- dest[((*n)++)]=1;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- }\r
- }\r
-\r
- // an fc/10 encoded bit is a bit pattern of 1110000000 x5 = 50 samples\r
- if(c==10) {\r
- for (idx=0; idx<5; idx++) {\r
- dest[((*n)++)]=1;\r
- dest[((*n)++)]=1;\r
- dest[((*n)++)]=1;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- dest[((*n)++)]=0;\r
- }\r
- }\r
-}\r
-\r
-// prepare a waveform pattern in the buffer based on the ID given then\r
-// simulate a HID tag until the button is pressed\r
-static void CmdHIDsimTAG(int hi, int lo)\r
-{\r
- int n=0, i=0;\r
- /*\r
- HID tag bitstream format\r
- The tag contains a 44bit unique code. This is sent out MSB first in sets of 4 bits\r
- A 1 bit is represented as 6 fc8 and 5 fc10 patterns\r
- A 0 bit is represented as 5 fc10 and 6 fc8 patterns\r
- A fc8 is inserted before every 4 bits\r
- A special start of frame pattern is used consisting a0b0 where a and b are neither 0\r
- nor 1 bits, they are special patterns (a = set of 12 fc8 and b = set of 10 fc10)\r
- */\r
-\r
- if (hi>0xFFF) {\r
- DbpString("Tags can only have 44 bits.");\r
- return;\r
- }\r
- fc(0,&n);\r
- // special start of frame marker containing invalid bit sequences\r
- fc(8, &n); fc(8, &n); // invalid\r
- fc(8, &n); fc(10, &n); // logical 0\r
- fc(10, &n); fc(10, &n); // invalid\r
- fc(8, &n); fc(10, &n); // logical 0\r
-\r
- WDT_HIT();\r
- // manchester encode bits 43 to 32\r
- for (i=11; i>=0; i--) {\r
- if ((i%4)==3) fc(0,&n);\r
- if ((hi>>i)&1) {\r
- fc(10, &n); fc(8, &n); // low-high transition\r
- } else {\r
- fc(8, &n); fc(10, &n); // high-low transition\r
- }\r
- }\r
-\r
- WDT_HIT();\r
- // manchester encode bits 31 to 0\r
- for (i=31; i>=0; i--) {\r
- if ((i%4)==3) fc(0,&n);\r
- if ((lo>>i)&1) {\r
- fc(10, &n); fc(8, &n); // low-high transition\r
- } else {\r
- fc(8, &n); fc(10, &n); // high-low transition\r
- }\r
- }\r
-\r
- LED_A_ON();\r
- SimulateTagLowFrequency(n);\r
- LED_A_OFF();\r
-}\r
-\r
-// loop to capture raw HID waveform then FSK demodulate the TAG ID from it\r
-static void CmdHIDdemodFSK(void)\r
-{\r
- BYTE *dest = (BYTE *)BigBuf;\r
- int m=0, n=0, i=0, idx=0, found=0, lastval=0;\r
- DWORD hi=0, lo=0;\r
-\r
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz\r
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER | FPGA_LF_READER_USE_125_KHZ);\r
-\r
- // Connect the A/D to the peak-detected low-frequency path.\r
- SetAdcMuxFor(GPIO_MUXSEL_LOPKD);\r
-\r
- // Give it a bit of time for the resonant antenna to settle.\r
- SpinDelay(50);\r
-\r
- // Now set up the SSC to get the ADC samples that are now streaming at us.\r
- FpgaSetupSsc();\r
-\r
- for(;;) {\r
- WDT_HIT();\r
- LED_A_ON();\r
- if(BUTTON_PRESS()) {\r
- LED_A_OFF();\r
- return;\r
- }\r
-\r
- i = 0;\r
- m = sizeof(BigBuf);\r
- memset(dest,128,m);\r
- for(;;) {\r
- if(SSC_STATUS & (SSC_STATUS_TX_READY)) {\r
- SSC_TRANSMIT_HOLDING = 0x43;\r
- LED_D_ON();\r
- }\r
- if(SSC_STATUS & (SSC_STATUS_RX_READY)) {\r
- dest[i] = (BYTE)SSC_RECEIVE_HOLDING;\r
- // we don't care about actual value, only if it's more or less than a\r
- // threshold essentially we capture zero crossings for later analysis\r
- if(dest[i] < 127) dest[i] = 0; else dest[i] = 1;\r
- i++;\r
- LED_D_OFF();\r
- if(i >= m) {\r
- break;\r
- }\r
- }\r
- }\r
-\r
- // FSK demodulator\r
-\r
- // sync to first lo-hi transition\r
- for( idx=1; idx<m; idx++) {\r
- if (dest[idx-1]<dest[idx])\r
- lastval=idx;\r
- break;\r
- }\r
- WDT_HIT();\r
-\r
- // count cycles between consecutive lo-hi transitions, there should be either 8 (fc/8)\r
- // or 10 (fc/10) cycles but in practice due to noise etc we may end up with with anywhere\r
- // between 7 to 11 cycles so fuzz it by treat anything <9 as 8 and anything else as 10\r
- for( i=0; idx<m; idx++) {\r
- if (dest[idx-1]<dest[idx]) {\r
- dest[i]=idx-lastval;\r
- if (dest[i] <= 8) {\r
- dest[i]=1;\r
- } else {\r
- dest[i]=0;\r
- }\r
-\r
- lastval=idx;\r
- i++;\r
- }\r
- }\r
- m=i;\r
- WDT_HIT();\r
-\r
- // we now have a set of cycle counts, loop over previous results and aggregate data into bit patterns\r
- lastval=dest[0];\r
- idx=0;\r
- i=0;\r
- n=0;\r
- for( idx=0; idx<m; idx++) {\r
- if (dest[idx]==lastval) {\r
- n++;\r
- } else {\r
- // a bit time is five fc/10 or six fc/8 cycles so figure out how many bits a pattern width represents,\r
- // an extra fc/8 pattern preceeds every 4 bits (about 200 cycles) just to complicate things but it gets\r
- // swallowed up by rounding\r
- // expected results are 1 or 2 bits, any more and it's an invalid manchester encoding\r
- // special start of frame markers use invalid manchester states (no transitions) by using sequences\r
- // like 111000\r
- if (dest[idx-1]) {\r
- n=(n+1)/6; // fc/8 in sets of 6\r
- } else {\r
- n=(n+1)/5; // fc/10 in sets of 5\r
- }\r
- switch (n) { // stuff appropriate bits in buffer\r
- case 0:\r
- case 1: // one bit\r
- dest[i++]=dest[idx-1];\r
- break;\r
- case 2: // two bits\r
- dest[i++]=dest[idx-1];\r
- dest[i++]=dest[idx-1];\r
- break;\r
- case 3: // 3 bit start of frame markers\r
- dest[i++]=dest[idx-1];\r
- dest[i++]=dest[idx-1];\r
- dest[i++]=dest[idx-1];\r
- break;\r
- // When a logic 0 is immediately followed by the start of the next transmisson\r
- // (special pattern) a pattern of 4 bit duration lengths is created.\r
- case 4:\r
- dest[i++]=dest[idx-1];\r
- dest[i++]=dest[idx-1];\r
- dest[i++]=dest[idx-1];\r
- dest[i++]=dest[idx-1];\r
- break;\r
- default: // this shouldn't happen, don't stuff any bits\r
- break;\r
- }\r
- n=0;\r
- lastval=dest[idx];\r
- }\r
- }\r
- m=i;\r
- WDT_HIT();\r
-\r
- // final loop, go over previously decoded manchester data and decode into usable tag ID\r
- // 111000 bit pattern represent start of frame, 01 pattern represents a 1 and 10 represents a 0\r
- for( idx=0; idx<m-6; idx++) {\r
- // search for a start of frame marker\r
- if ( dest[idx] && dest[idx+1] && dest[idx+2] && (!dest[idx+3]) && (!dest[idx+4]) && (!dest[idx+5]) )\r
- {\r
- found=1;\r
- idx+=6;\r
- if (found && (hi|lo)) {\r
- DbpString("TAG ID");\r
- DbpIntegers(hi, lo, (lo>>1)&0xffff);\r
- hi=0;\r
- lo=0;\r
- found=0;\r
- }\r
- }\r
- if (found) {\r
- if (dest[idx] && (!dest[idx+1]) ) {\r
- hi=(hi<<1)|(lo>>31);\r
- lo=(lo<<1)|0;\r
- } else if ( (!dest[idx]) && dest[idx+1]) {\r
- hi=(hi<<1)|(lo>>31);\r
- lo=(lo<<1)|1;\r
- } else {\r
- found=0;\r
- hi=0;\r
- lo=0;\r
- }\r
- idx++;\r
- }\r
- if ( dest[idx] && dest[idx+1] && dest[idx+2] && (!dest[idx+3]) && (!dest[idx+4]) && (!dest[idx+5]) )\r
- {\r
- found=1;\r
- idx+=6;\r
- if (found && (hi|lo)) {\r
- DbpString("TAG ID");\r
- DbpIntegers(hi, lo, (lo>>1)&0xffff);\r
- hi=0;\r
- lo=0;\r
- found=0;\r
- }\r
- }\r
- }\r
- WDT_HIT();\r
- }\r
-}\r
-\r
-void SimulateTagHfListen(void)\r
-{\r
- BYTE *dest = (BYTE *)BigBuf;\r
- int n = sizeof(BigBuf);\r
- BYTE v = 0;\r
- int i;\r
- int p = 0;\r
-\r
- // We're using this mode just so that I can test it out; the simulated\r
- // tag mode would work just as well and be simpler.\r
- FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_READER_RX_XCORR | FPGA_HF_READER_RX_XCORR_848_KHZ | FPGA_HF_READER_RX_XCORR_SNOOP);\r
-\r
- // We need to listen to the high-frequency, peak-detected path.\r
- SetAdcMuxFor(GPIO_MUXSEL_HIPKD);\r
-\r
- FpgaSetupSsc();\r
-\r
- i = 0;\r
- for(;;) {\r
- if(SSC_STATUS & (SSC_STATUS_TX_READY)) {\r
- SSC_TRANSMIT_HOLDING = 0xff;\r
- }\r
- if(SSC_STATUS & (SSC_STATUS_RX_READY)) {\r
- BYTE r = (BYTE)SSC_RECEIVE_HOLDING;\r
-\r
- v <<= 1;\r
- if(r & 1) {\r
- v |= 1;\r
- }\r
- p++;\r
-\r
- if(p >= 8) {\r
- dest[i] = v;\r
- v = 0;\r
- p = 0;\r
- i++;\r
-\r
- if(i >= n) {\r
- break;\r
- }\r
- }\r
- }\r
- }\r
- DbpString("simulate tag (now type bitsamples)");\r
-}\r
-\r
-void UsbPacketReceived(BYTE *packet, int len)\r
-{\r
- UsbCommand *c = (UsbCommand *)packet;\r
-\r
- switch(c->cmd) {\r
- case CMD_ACQUIRE_RAW_ADC_SAMPLES_125K:\r
- AcquireRawAdcSamples125k(c->ext1);\r
- break;\r
-\r
- case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_15693:\r
- AcquireRawAdcSamplesIso15693();\r
- break;\r
-\r
- case CMD_READER_ISO_15693:\r
- ReaderIso15693(c->ext1);\r
- break;\r
-\r
- case CMD_SIMTAG_ISO_15693:\r
- SimTagIso15693(c->ext1);\r
- break;\r
-\r
- case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_14443:\r
- AcquireRawAdcSamplesIso14443(c->ext1);\r
- break;\r
+ * read the voltage in the antenna, the result left
+ * in the buffer is a graph which should clearly show
+ * the resonating frequency of your LF antenna
+ * ( hopefully around 95 if it is tuned to 125kHz!)
+ */
+ FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER);
+ for (i=255; i>19; i--) {
+ FpgaSendCommand(FPGA_CMD_SET_DIVISOR, i);
+ SpinDelay(20);
+ // Vref = 3.3V, and a 10000:240 voltage divider on the input
+ // can measure voltages up to 137500 mV
+ adcval = ((137500 * AvgAdc(ADC_CHAN_LF)) >> 10);
+ if (i==95) vLf125 = adcval; // voltage at 125Khz
+ if (i==89) vLf134 = adcval; // voltage at 134Khz
+
+ dest[i] = adcval>>8; // scale int to fit in byte for graphing purposes
+ if(dest[i] > peak) {
+ peakv = adcval;
+ peak = dest[i];
+ peakf = i;
+ ptr = i;
+ }
+ }
+
+ // Let the FPGA drive the high-frequency antenna around 13.56 MHz.
+ FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_READER_RX_XCORR);
+ SpinDelay(20);
+ // Vref = 3300mV, and an 10:1 voltage divider on the input
+ // can measure voltages up to 33000 mV
+ vHf = (33000 * AvgAdc(ADC_CHAN_HF)) >> 10;
+
+ c.cmd = CMD_MEASURED_ANTENNA_TUNING;
+ c.ext1 = (vLf125 << 0) | (vLf134 << 16);
+ c.ext2 = vHf;
+ c.ext3 = peakf | (peakv << 16);
+ UsbSendPacket((BYTE *)&c, sizeof(c));
+}
+
+void SimulateTagHfListen(void)
+{
+ BYTE *dest = (BYTE *)BigBuf;
+ int n = sizeof(BigBuf);
+ BYTE v = 0;
+ int i;
+ int p = 0;
+
+ // We're using this mode just so that I can test it out; the simulated
+ // tag mode would work just as well and be simpler.
+ FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_READER_RX_XCORR | FPGA_HF_READER_RX_XCORR_848_KHZ | FPGA_HF_READER_RX_XCORR_SNOOP);
+
+ // We need to listen to the high-frequency, peak-detected path.
+ SetAdcMuxFor(GPIO_MUXSEL_HIPKD);
+
+ FpgaSetupSsc();
+
+ i = 0;
+ for(;;) {
+ if(SSC_STATUS & (SSC_STATUS_TX_READY)) {
+ SSC_TRANSMIT_HOLDING = 0xff;
+ }
+ if(SSC_STATUS & (SSC_STATUS_RX_READY)) {
+ BYTE r = (BYTE)SSC_RECEIVE_HOLDING;
+
+ v <<= 1;
+ if(r & 1) {
+ v |= 1;
+ }
+ p++;
+
+ if(p >= 8) {
+ dest[i] = v;
+ v = 0;
+ p = 0;
+ i++;
+
+ if(i >= n) {
+ break;
+ }
+ }
+ }
+ }
+ DbpString("simulate tag (now type bitsamples)");
+}
+
+void ReadMem(int addr)
+{
+ const DWORD *data = ((DWORD *)addr);
+ int i;
+
+ DbpString("Reading memory at address");
+ DbpIntegers(0, 0, addr);
+ for (i = 0; i < 8; i+= 2)
+ DbpIntegers(0, data[i], data[i+1]);
+}
+
+/* osimage version information is linked in */
+extern struct version_information version_information;
+/* bootrom version information is pointed to from _bootphase1_version_pointer */
+extern char *_bootphase1_version_pointer, _flash_start, _flash_end;
+void SendVersion(void)
+{
+ char temp[48]; /* Limited data payload in USB packets */
+ DbpString("Prox/RFID mark3 RFID instrument");
+
+ /* Try to find the bootrom version information. Expect to find a pointer at
+ * symbol _bootphase1_version_pointer, perform slight sanity checks on the
+ * pointer, then use it.
+ */
+ char *bootrom_version = *(char**)&_bootphase1_version_pointer;
+ if( bootrom_version < &_flash_start || bootrom_version >= &_flash_end ) {
+ DbpString("bootrom version information appears invalid");
+ } else {
+ FormatVersionInformation(temp, sizeof(temp), "bootrom: ", bootrom_version);
+ DbpString(temp);
+ }
+
+ FormatVersionInformation(temp, sizeof(temp), "os: ", &version_information);
+ DbpString(temp);
+
+ FpgaGatherVersion(temp, sizeof(temp));
+ DbpString(temp);
+}
+
+// samy's sniff and repeat routine
+void SamyRun()
+{
+ DbpString("Stand-alone mode! No PC necessary.");
+
+ // 3 possible options? no just 2 for now
+#define OPTS 2
+
+ int high[OPTS], low[OPTS];
+
+ // Oooh pretty -- notify user we're in elite samy mode now
+ LED(LED_RED, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_GREEN, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_RED, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_GREEN, 200);
+ LED(LED_ORANGE, 200);
+ LED(LED_RED, 200);
+
+ int selected = 0;
+ int playing = 0;
+
+ // Turn on selected LED
+ LED(selected + 1, 0);
+
+ for (;;)
+ {
+ UsbPoll(FALSE);
+ WDT_HIT();
+
+ // Was our button held down or pressed?
+ int button_pressed = BUTTON_HELD(1000);
+ SpinDelay(300);
+
+ // Button was held for a second, begin recording
+ if (button_pressed > 0)
+ {
+ LEDsoff();
+ LED(selected + 1, 0);
+ LED(LED_RED2, 0);
+
+ // record
+ DbpString("Starting recording");
+
+ // wait for button to be released
+ while(BUTTON_PRESS())
+ WDT_HIT();
+
+ /* need this delay to prevent catching some weird data */
+ SpinDelay(500);
+
+ CmdHIDdemodFSK(1, &high[selected], &low[selected], 0);
+ DbpString("Recorded");
+ DbpIntegers(selected, high[selected], low[selected]);
+
+ LEDsoff();
+ LED(selected + 1, 0);
+ // Finished recording
+
+ // If we were previously playing, set playing off
+ // so next button push begins playing what we recorded
+ playing = 0;
+ }
+
+ // Change where to record (or begin playing)
+ else if (button_pressed)
+ {
+ // Next option if we were previously playing
+ if (playing)
+ selected = (selected + 1) % OPTS;
+ playing = !playing;
+
+ LEDsoff();
+ LED(selected + 1, 0);
+
+ // Begin transmitting
+ if (playing)
+ {
+ LED(LED_GREEN, 0);
+ DbpString("Playing");
+ // wait for button to be released
+ while(BUTTON_PRESS())
+ WDT_HIT();
+ DbpIntegers(selected, high[selected], low[selected]);
+ CmdHIDsimTAG(high[selected], low[selected], 0);
+ DbpString("Done playing");
+ if (BUTTON_HELD(1000) > 0)
+ {
+ DbpString("Exiting");
+ LEDsoff();
+ return;
+ }
+
+ /* We pressed a button so ignore it here with a delay */
+ SpinDelay(300);
+
+ // when done, we're done playing, move to next option
+ selected = (selected + 1) % OPTS;
+ playing = !playing;
+ LEDsoff();
+ LED(selected + 1, 0);
+ }
+ else
+ while(BUTTON_PRESS())
+ WDT_HIT();
+ }
+ }
+}
+
+
+/*
+OBJECTIVE
+Listen and detect an external reader. Determine the best location
+for the antenna.
+
+INSTRUCTIONS:
+Inside the ListenReaderField() function, there is two mode.
+By default, when you call the function, you will enter mode 1.
+If you press the PM3 button one time, you will enter mode 2.
+If you press the PM3 button a second time, you will exit the function.
+
+DESCRIPTION OF MODE 1:
+This mode just listens for an external reader field and lights up green
+for HF and/or red for LF. This is the original mode of the detectreader
+function.
+
+DESCRIPTION OF MODE 2:
+This mode will visually represent, using the LEDs, the actual strength of the
+current compared to the maximum current detected. Basically, once you know
+what kind of external reader is present, it will help you spot the best location to place
+your antenna. You will probably not get some good results if there is a LF and a HF reader
+at the same place! :-)
+
+LIGHT SCHEME USED:
+*/
+static const char LIGHT_SCHEME[] = {
+ 0x0, /* ---- | No field detected */
+ 0x1, /* X--- | 14% of maximum current detected */
+ 0x2, /* -X-- | 29% of maximum current detected */
+ 0x4, /* --X- | 43% of maximum current detected */
+ 0x8, /* ---X | 57% of maximum current detected */
+ 0xC, /* --XX | 71% of maximum current detected */
+ 0xE, /* -XXX | 86% of maximum current detected */
+ 0xF, /* XXXX | 100% of maximum current detected */
+};
+static const int LIGHT_LEN = sizeof(LIGHT_SCHEME)/sizeof(LIGHT_SCHEME[0]);
+
+void ListenReaderField(int limit)
+{
+ int lf_av, lf_av_new, lf_baseline= 0, lf_count= 0, lf_max;
+ int hf_av, hf_av_new, hf_baseline= 0, hf_count= 0, hf_max;
+ int mode=1, display_val, display_max, i;
+
+#define LF_ONLY 1
+#define HF_ONLY 2
+
+ LEDsoff();
+
+ lf_av=lf_max=ReadAdc(ADC_CHAN_LF);
+
+ if(limit != HF_ONLY) {
+ DbpString("LF 125/134 Baseline:");
+ DbpIntegers(lf_av,0,0);
+ lf_baseline= lf_av;
+ }
+
+ hf_av=hf_max=ReadAdc(ADC_CHAN_HF);
+
+ if (limit != LF_ONLY) {
+ DbpString("HF 13.56 Baseline:");
+ DbpIntegers(hf_av,0,0);
+ hf_baseline= hf_av;
+ }
+
+ for(;;) {
+ if (BUTTON_PRESS()) {
+ SpinDelay(500);
+ switch (mode) {
+ case 1:
+ mode=2;
+ DbpString("Signal Strength Mode");
+ break;
+ case 2:
+ default:
+ DbpString("Stopped");
+ LEDsoff();
+ return;
+ break;
+ }
+ }
+ WDT_HIT();
+
+ if (limit != HF_ONLY) {
+ if(mode==1) {
+ if (abs(lf_av - lf_baseline) > 10) LED_D_ON();
+ else LED_D_OFF();
+ }
+
+ ++lf_count;
+ lf_av_new= ReadAdc(ADC_CHAN_LF);
+ // see if there's a significant change
+ if(abs(lf_av - lf_av_new) > 10) {
+ DbpString("LF 125/134 Field Change:");
+ DbpIntegers(lf_av,lf_av_new,lf_count);
+ lf_av= lf_av_new;
+ if (lf_av > lf_max)
+ lf_max = lf_av;
+ lf_count= 0;
+ }
+ }
+
+ if (limit != LF_ONLY) {
+ if (mode == 1){
+ if (abs(hf_av - hf_baseline) > 10) LED_B_ON();
+ else LED_B_OFF();
+ }
+
+ ++hf_count;
+ hf_av_new= ReadAdc(ADC_CHAN_HF);
+ // see if there's a significant change
+ if(abs(hf_av - hf_av_new) > 10) {
+ DbpString("HF 13.56 Field Change:");
+ DbpIntegers(hf_av,hf_av_new,hf_count);
+ hf_av= hf_av_new;
+ if (hf_av > hf_max)
+ hf_max = hf_av;
+ hf_count= 0;
+ }
+ }
+
+ if(mode == 2) {
+ if (limit == LF_ONLY) {
+ display_val = lf_av;
+ display_max = lf_max;
+ } else if (limit == HF_ONLY) {
+ display_val = hf_av;
+ display_max = hf_max;
+ } else { /* Pick one at random */
+ if( (hf_max - hf_baseline) > (lf_max - lf_baseline) ) {
+ display_val = hf_av;
+ display_max = hf_max;
+ } else {
+ display_val = lf_av;
+ display_max = lf_max;
+ }
+ }
+ for (i=0; i<LIGHT_LEN; i++) {
+ if (display_val >= ((display_max/LIGHT_LEN)*i) && display_val <= ((display_max/LIGHT_LEN)*(i+1))) {
+ if (LIGHT_SCHEME[i] & 0x1) LED_C_ON(); else LED_C_OFF();
+ if (LIGHT_SCHEME[i] & 0x2) LED_A_ON(); else LED_A_OFF();
+ if (LIGHT_SCHEME[i] & 0x4) LED_B_ON(); else LED_B_OFF();
+ if (LIGHT_SCHEME[i] & 0x8) LED_D_ON(); else LED_D_OFF();
+ break;
+ }
+ }
+ }
+ }
+}
+
+void UsbPacketReceived(BYTE *packet, int len)
+{
+ UsbCommand *c = (UsbCommand *)packet;
+
+ switch(c->cmd) {
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_125K:
+ AcquireRawAdcSamples125k(c->ext1);
+ break;
+
+ case CMD_MOD_THEN_ACQUIRE_RAW_ADC_SAMPLES_125K:
+ ModThenAcquireRawAdcSamples125k(c->ext1,c->ext2,c->ext3,c->d.asBytes);
+ break;
+
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_15693:
+ AcquireRawAdcSamplesIso15693();
+ break;
+
+ case CMD_BUFF_CLEAR:
+ BufferClear();
+ break;
+
+ case CMD_READER_ISO_15693:
+ ReaderIso15693(c->ext1);
+ break;
+
+ case CMD_SIMTAG_ISO_15693:
+ SimTagIso15693(c->ext1);
+ break;
+
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_14443:
+ AcquireRawAdcSamplesIso14443(c->ext1);
+ break;
projects / proxmark3-svn / blobdiff