Merge pull request #98 from marshmellow42/master

[proxmark3-svn] / fpga / lo_read.v

diff --git a/fpga/lo_read.v b/fpga/lo_read.v
index e6f245ca67b2e403fcee1aba89c6584e21be9efe..a6d077b99697ea4d597c02975b53885df69490ab 100644 (file)
--- a/fpga/lo_read.v
+++ b/fpga/lo_read.v
@@ -4,68 +4,39 @@
 // The A/D samples at that same rate and the result is serialized.
 //
 // Jonathan Westhues, April 2006
+// iZsh <izsh at fail0verflow.com>, June 2014
 //-----------------------------------------------------------------------------
 
 module lo_read(
-    pck0, ck_1356meg, ck_1356megb,
-    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
-    adc_d, adc_clk,
-    ssp_frame, ssp_din, ssp_dout, ssp_clk,
-    cross_hi, cross_lo,
-    dbg,
-    lo_is_125khz, divisor
+       input pck0, input [7:0] pck_cnt, input pck_divclk,
+       output pwr_lo, output pwr_hi,
+       output pwr_oe1, output pwr_oe2, output pwr_oe3, output pwr_oe4,
+       input [7:0] adc_d, output adc_clk,
+       output ssp_frame, output ssp_din, output ssp_clk,
+       output dbg,
+       input lf_field
 );
-    input pck0, ck_1356meg, ck_1356megb;
-    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
-    input [7:0] adc_d;
-    output adc_clk;
-    input ssp_dout;
-    output ssp_frame, ssp_din, ssp_clk;
-    input cross_hi, cross_lo;
-    output dbg;
-    input lo_is_125khz; // redundant signal, no longer used anywhere
-    input [7:0] divisor;
 
 reg [7:0] to_arm_shiftreg;
-reg [7:0] pck_divider;
-reg ant_lo;
-
-// this task runs on the rising egde of pck0 clock (24Mhz) and creates ant_lo
-// which is high for (divisor+1) pck0 cycles and low for the same duration
-// ant_lo is therefore a 50% duty cycle clock signal with a frequency of
-// 12Mhz/(divisor+1) which drives the antenna as well as the ADC clock adc_clk
-always @(posedge pck0)
-begin
-       if(pck_divider == divisor[7:0])
-               begin
-                       pck_divider <= 8'd0;
-                       ant_lo = !ant_lo;
-               end
-       else
-       begin
-               pck_divider <= pck_divider + 1;
-       end
-end
 
 // this task also runs at pck0 frequency (24Mhz) and is used to serialize
 // the ADC output which is then clocked into the ARM SSP.
 
-// because ant_lo always transitions when pck_divider = 0 we use the
-// pck_divider counter to sync our other signals off it
-// we read the ADC value when pck_divider=7 and shift it out on counts 8..15
+// because pck_divclk always transitions when pck_cnt = 0 we use the
+// pck_div counter to sync our other signals off it
+// we read the ADC value when pck_cnt=7 and shift it out on counts 8..15
 always @(posedge pck0)
 begin
-       if((pck_divider == 8'd7) && !ant_lo)
-        to_arm_shiftreg <= adc_d;
-    else
-       begin
-        to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
+       if((pck_cnt == 8'd7) && !pck_divclk)
+               to_arm_shiftreg <= adc_d;
+       else begin
+               to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
                // simulation showed a glitch occuring due to the LSB of the shifter
                // not being set as we shift bits out
                // this ensures the ssp_din remains low after a transfer and suppresses
                // the glitch that would occur when the last data shifted out ended in
                // a 1 bit and the next data shifted out started with a 0 bit
-        to_arm_shiftreg[0] <= 1'b0;
+               to_arm_shiftreg[0] <= 1'b0;
        end
 end
 
@@ -83,11 +54,11 @@ end
 // ssp_clk  |_| |_| |_| |_| |_| |_| |_| |_| |_| |_
 
 // serialized SSP data is gated by ant_lo to suppress unwanted signal
-assign ssp_din = to_arm_shiftreg[7] && !ant_lo;
+assign ssp_din = to_arm_shiftreg[7] && !pck_divclk;
 // SSP clock always runs at 24Mhz
 assign ssp_clk = pck0;
 // SSP frame is gated by ant_lo and goes high when pck_divider=8..15
-assign ssp_frame = (pck_divider[7:3] == 5'd1) && !ant_lo;
+assign ssp_frame = (pck_cnt[7:3] == 5'd1) && !pck_divclk;
 // unused signals tied low
 assign pwr_hi = 1'b0;
 assign pwr_oe1 = 1'b0;
@@ -95,9 +66,9 @@ assign pwr_oe2 = 1'b0;
 assign pwr_oe3 = 1'b0;
 assign pwr_oe4 = 1'b0;
 // this is the antenna driver signal
-assign pwr_lo = ant_lo;
+assign pwr_lo = lf_field & pck_divclk;
 // ADC clock out of phase with antenna driver
-assign adc_clk = ~ant_lo;
+assign adc_clk = ~pck_divclk;
 // ADC clock also routed to debug pin
 assign dbg = adc_clk;
 endmodule