+ }
+
+ if (ii<2) return 0; // oops we went too far
+
+ return clk[ii];
+}
+
+uint8_t detectFSKClk(uint8_t *BitStream, size_t size, uint8_t fcHigh, uint8_t fcLow) {
+ int firstClockEdge = 0;
+ return detectFSKClk_ext(BitStream, size, fcHigh, fcLow, &firstClockEdge);
+}
+
+//**********************************************************************************************
+//--------------------Modulation Demods &/or Decoding Section-----------------------------------
+//**********************************************************************************************
+
+// look for Sequence Terminator - should be pulses of clk*(1 or 2), clk*2, clk*(1.5 or 2), by idx we mean graph position index...
+bool findST(int *stStopLoc, int *stStartIdx, int lowToLowWaveLen[], int highToLowWaveLen[], int clk, int tol, int buffSize, size_t *i) {
+ for (; *i < buffSize - 4; *i+=1) {
+ *stStartIdx += lowToLowWaveLen[*i]; //caution part of this wave may be data and part may be ST.... to be accounted for in main function for now...
+ if (lowToLowWaveLen[*i] >= clk*1-tol && lowToLowWaveLen[*i] <= (clk*2)+tol && highToLowWaveLen[*i] < clk+tol) { //1 to 2 clocks depending on 2 bits prior
+ if (lowToLowWaveLen[*i+1] >= clk*2-tol && lowToLowWaveLen[*i+1] <= clk*2+tol && highToLowWaveLen[*i+1] > clk*3/2-tol) { //2 clocks and wave size is 1 1/2
+ if (lowToLowWaveLen[*i+2] >= (clk*3)/2-tol && lowToLowWaveLen[*i+2] <= clk*2+tol && highToLowWaveLen[*i+2] > clk-tol) { //1 1/2 to 2 clocks and at least one full clock wave
+ if (lowToLowWaveLen[*i+3] >= clk*1-tol && lowToLowWaveLen[*i+3] <= clk*2+tol) { //1 to 2 clocks for end of ST + first bit
+ *stStopLoc = *i + 3;
+ return true;
+ }
+ }
+ }
+ }
+ }
+ return false;
+}
+//by marshmellow
+//attempt to identify a Sequence Terminator in ASK modulated raw wave
+bool DetectST_ext(uint8_t buffer[], size_t *size, int *foundclock, size_t *ststart, size_t *stend) {
+ size_t bufsize = *size;
+ //need to loop through all samples and identify our clock, look for the ST pattern
+ int clk = 0;
+ int tol = 0;
+ int j, high, low, skip, start, end, minClk=255;
+ size_t i = 0;
+ //probably should malloc... || test if memory is available ... handle device side? memory danger!!! [marshmellow]
+ int tmpbuff[bufsize / LOWEST_DEFAULT_CLOCK]; // low to low wave count //guess rf/32 clock, if click is smaller we will only have room for a fraction of the samples captured
+ int waveLen[bufsize / LOWEST_DEFAULT_CLOCK]; // high to low wave count //if clock is larger then we waste memory in array size that is not needed...
+ //size_t testsize = (bufsize < 512) ? bufsize : 512;
+ int phaseoff = 0;
+ high = low = 128;
+ memset(tmpbuff, 0, sizeof(tmpbuff));
+ memset(waveLen, 0, sizeof(waveLen));
+
+ if (!loadWaveCounters(buffer, bufsize, tmpbuff, waveLen, &j, &skip, &minClk, &high, &low)) return false;
+ // set clock - might be able to get this externally and remove this work...
+ clk = getClosestClock(minClk);
+ // clock not found - ERROR
+ if (clk == 0) {
+ if (g_debugMode==2) prnt("DEBUG STT: clock not found - quitting");
+ return false;
+ }
+ *foundclock = clk;
+
+ tol = clk/8;
+ if (!findST(&start, &skip, tmpbuff, waveLen, clk, tol, j, &i)) {
+ // first ST not found - ERROR
+ if (g_debugMode==2) prnt("DEBUG STT: first STT not found - quitting");
+ return false;
+ } else {
+ if (g_debugMode==2) prnt("DEBUG STT: first STT found at wave: %i, skip: %i, j=%i", start, skip, j);
+ }
+ if (waveLen[i+2] > clk*1+tol)
+ phaseoff = 0;
+ else
+ phaseoff = clk/2;
+
+ // skip over the remainder of ST
+ skip += clk*7/2; //3.5 clocks from tmpbuff[i] = end of st - also aligns for ending point
+
+ // now do it again to find the end
+ int dummy1 = 0;
+ end = skip;
+ i+=3;
+ if (!findST(&dummy1, &end, tmpbuff, waveLen, clk, tol, j, &i)) {
+ //didn't find second ST - ERROR
+ if (g_debugMode==2) prnt("DEBUG STT: second STT not found - quitting");
+ return false;
+ }
+ end -= phaseoff;
+ if (g_debugMode==2) prnt("DEBUG STT: start of data: %d end of data: %d, datalen: %d, clk: %d, bits: %d, phaseoff: %d", skip, end, end-skip, clk, (end-skip)/clk, phaseoff);
+ //now begin to trim out ST so we can use normal demod cmds
+ start = skip;
+ size_t datalen = end - start;
+ // check validity of datalen (should be even clock increments) - use a tolerance of up to 1/8th a clock
+ if ( clk - (datalen % clk) <= clk/8) {
+ // padd the amount off - could be problematic... but shouldn't happen often
+ datalen += clk - (datalen % clk);
+ } else if ( (datalen % clk) <= clk/8 ) {
+ // padd the amount off - could be problematic... but shouldn't happen often
+ datalen -= datalen % clk;
+ } else {
+ if (g_debugMode==2) prnt("DEBUG STT: datalen not divisible by clk: %u %% %d = %d - quitting", datalen, clk, datalen % clk);
+ return false;
+ }
+ // if datalen is less than one t55xx block - ERROR
+ if (datalen/clk < 8*4) {
+ if (g_debugMode==2) prnt("DEBUG STT: datalen is less than 1 full t55xx block - quitting");
+ return false;
+ }
+ size_t dataloc = start;
+ if (buffer[dataloc-(clk*4)-(clk/8)] <= low && buffer[dataloc] <= low && buffer[dataloc-(clk*4)] >= high) {
+ //we have low drift (and a low just before the ST and a low just after the ST) - compensate by backing up the start
+ for ( i=0; i <= (clk/8); ++i ) {
+ if ( buffer[dataloc - (clk*4) - i] <= low ) {
+ dataloc -= i;
+ break;
+ }
+ }
+ }
+
+ size_t newloc = 0;
+ i=0;
+ if (g_debugMode==2) prnt("DEBUG STT: Starting STT trim - start: %d, datalen: %d ",dataloc, datalen);
+ bool firstrun = true;
+ // warning - overwriting buffer given with raw wave data with ST removed...
+ while ( dataloc < bufsize-(clk/2) ) {
+ //compensate for long high at end of ST not being high due to signal loss... (and we cut out the start of wave high part)
+ if (buffer[dataloc]<high && buffer[dataloc]>low && buffer[dataloc+3]<high && buffer[dataloc+3]>low) {
+ for(i=0; i < clk/2-tol; ++i) {
+ buffer[dataloc+i] = high+5;
+ }
+ } //test for single sample outlier (high between two lows) in the case of very strong waves
+ if (buffer[dataloc] >= high && buffer[dataloc+2] <= low) {
+ buffer[dataloc] = buffer[dataloc+2];
+ buffer[dataloc+1] = buffer[dataloc+2];
+ }
+ if (firstrun) {
+ *stend = dataloc;
+ *ststart = dataloc-(clk*4);
+ firstrun=false;
+ }
+ for (i=0; i<datalen; ++i) {
+ if (i+newloc < bufsize) {
+ if (i+newloc < dataloc)
+ buffer[i+newloc] = buffer[dataloc];
+
+ dataloc++;
+ }
+ }
+ newloc += i;
+ //skip next ST - we just assume it will be there from now on...
+ if (g_debugMode==2) prnt("DEBUG STT: skipping STT at %d to %d", dataloc, dataloc+(clk*4));
+ dataloc += clk*4;
+ }
+ *size = newloc;
+ return true;
+}
+bool DetectST(uint8_t buffer[], size_t *size, int *foundclock) {
+ size_t ststart = 0, stend = 0;
+ return DetectST_ext(buffer, size, foundclock, &ststart, &stend);
+}
+
+//by marshmellow
+//take 11 10 01 11 00 and make 01100 ... miller decoding
+//check for phase errors - should never have half a 1 or 0 by itself and should never exceed 1111 or 0000 in a row
+//decodes miller encoded binary
+//NOTE askrawdemod will NOT demod miller encoded ask unless the clock is manually set to 1/2 what it is detected as!
+int millerRawDecode(uint8_t *BitStream, size_t *size, int invert) {
+ if (*size < 16) return -1;
+ uint16_t MaxBits = 512, errCnt = 0;
+ size_t i, bitCnt=0;
+ uint8_t alignCnt = 0, curBit = BitStream[0], alignedIdx = 0;
+ uint8_t halfClkErr = 0;
+ //find alignment, needs 4 1s or 0s to properly align
+ for (i=1; i < *size-1; i++) {
+ alignCnt = (BitStream[i] == curBit) ? alignCnt+1 : 0;
+ curBit = BitStream[i];
+ if (alignCnt == 4) break;
+ }
+ // for now error if alignment not found. later add option to run it with multiple offsets...
+ if (alignCnt != 4) {
+ if (g_debugMode) prnt("ERROR MillerDecode: alignment not found so either your bitstream is not miller or your data does not have a 101 in it");
projects / proxmark3-svn / blobdiff