fix Mac build to use Qt framework

[proxmark3-svn] / armsrc / fpgaloader.c

diff --git a/armsrc/fpgaloader.c b/armsrc/fpgaloader.c
index af2f02abaf6df550a9f93d2cf313a868bb16ddf5..04db41b3c38ebc97fe948fe524918f8e1ca6b38b 100644 (file)
--- a/armsrc/fpgaloader.c
+++ b/armsrc/fpgaloader.c
@@ -21,27 +21,29 @@ void SetupSpi(int mode)
        // PA14 -> SPI_SPCK Serial Clock\r
 \r
        // Disable PIO control of the following pins, allows use by the SPI peripheral\r
        // PA14 -> SPI_SPCK Serial Clock\r
 \r
        // Disable PIO control of the following pins, allows use by the SPI peripheral\r

-       PIO_DISABLE                      =      (1 << GPIO_NCS0)        |\r
-                                                       (1 << GPIO_NCS2)        |\r
-                                                       (1 << GPIO_MISO)        |\r
-                                                       (1 << GPIO_MOSI)        |\r
-                                                       (1 << GPIO_SPCK);\r
+       AT91C_BASE_PIOA->PIO_PDR =\r
+               GPIO_NCS0       |\r
+               GPIO_NCS2       |\r
+               GPIO_MISO       |\r
+               GPIO_MOSI       |\r
+               GPIO_SPCK;\r

 \r
 \r

-       PIO_PERIPHERAL_A_SEL =  (1 << GPIO_NCS0)        |\r
-                                                       (1 << GPIO_MISO)        |\r
-                                                       (1 << GPIO_MOSI)        |\r
-                                                       (1 << GPIO_SPCK);\r
+       AT91C_BASE_PIOA->PIO_ASR =\r
+               GPIO_NCS0       |\r
+               GPIO_MISO       |\r
+               GPIO_MOSI       |\r
+               GPIO_SPCK;\r

 \r
 \r

-       PIO_PERIPHERAL_B_SEL =  (1 << GPIO_NCS2);\r
+       AT91C_BASE_PIOA->PIO_BSR = GPIO_NCS2;\r

 \r
        //enable the SPI Peripheral clock\r
 \r
        //enable the SPI Peripheral clock\r

-       PMC_PERIPHERAL_CLK_ENABLE = (1<<PERIPH_SPI);\r
+       AT91C_BASE_PMC->PMC_PCER = (1<<AT91C_ID_SPI);\r

        // Enable SPI\r
        // Enable SPI\r

-       SPI_CONTROL = SPI_CONTROL_ENABLE;\r
+       AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIEN;\r

 \r
        switch (mode) {\r
                case SPI_FPGA_MODE:\r
 \r
        switch (mode) {\r
                case SPI_FPGA_MODE:\r

-                       SPI_MODE =\r
+                       AT91C_BASE_SPI->SPI_MR =\r

                                ( 0 << 24)      |       // Delay between chip selects (take default: 6 MCK periods)\r
                                (14 << 16)      |       // Peripheral Chip Select (selects FPGA SPI_NCS0 or PA11)\r
                                ( 0 << 7)       |       // Local Loopback Disabled\r
                                ( 0 << 24)      |       // Delay between chip selects (take default: 6 MCK periods)\r
                                (14 << 16)      |       // Peripheral Chip Select (selects FPGA SPI_NCS0 or PA11)\r
                                ( 0 << 7)       |       // Local Loopback Disabled\r


@@ -49,7 +51,7 @@ void SetupSpi(int mode)
                                ( 0 << 2)       |       // Chip selects connected directly to peripheral\r
                                ( 0 << 1)       |       // Fixed Peripheral Select\r
                                ( 1 << 0);              // Master Mode\r
                                ( 0 << 2)       |       // Chip selects connected directly to peripheral\r
                                ( 0 << 1)       |       // Fixed Peripheral Select\r
                                ( 1 << 0);              // Master Mode\r

-                       SPI_FOR_CHIPSEL_0 =\r
+                       AT91C_BASE_SPI->SPI_CSR[0] =\r

                                ( 1 << 24)      |       // Delay between Consecutive Transfers (32 MCK periods)\r
                                ( 1 << 16)      |       // Delay Before SPCK (1 MCK period)\r
                                ( 6 << 8)       |       // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud\r
                                ( 1 << 24)      |       // Delay between Consecutive Transfers (32 MCK periods)\r
                                ( 1 << 16)      |       // Delay Before SPCK (1 MCK period)\r
                                ( 6 << 8)       |       // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud\r


@@ -59,7 +61,7 @@ void SetupSpi(int mode)
                                ( 0 << 0);              // Clock Polarity inactive state is logic 0\r
                        break;\r
                case SPI_LCD_MODE:\r
                                ( 0 << 0);              // Clock Polarity inactive state is logic 0\r
                        break;\r
                case SPI_LCD_MODE:\r

-                       SPI_MODE =\r
+                       AT91C_BASE_SPI->SPI_MR =\r

                                ( 0 << 24)      |       // Delay between chip selects (take default: 6 MCK periods)\r
                                (11 << 16)      |       // Peripheral Chip Select (selects LCD SPI_NCS2 or PA10)\r
                                ( 0 << 7)       |       // Local Loopback Disabled\r
                                ( 0 << 24)      |       // Delay between chip selects (take default: 6 MCK periods)\r
                                (11 << 16)      |       // Peripheral Chip Select (selects LCD SPI_NCS2 or PA10)\r
                                ( 0 << 7)       |       // Local Loopback Disabled\r


@@ -67,7 +69,7 @@ void SetupSpi(int mode)
                                ( 0 << 2)       |       // Chip selects connected directly to peripheral\r
                                ( 0 << 1)       |       // Fixed Peripheral Select\r
                                ( 1 << 0);              // Master Mode\r
                                ( 0 << 2)       |       // Chip selects connected directly to peripheral\r
                                ( 0 << 1)       |       // Fixed Peripheral Select\r
                                ( 1 << 0);              // Master Mode\r

-                       SPI_FOR_CHIPSEL_2 =\r
+                       AT91C_BASE_SPI->SPI_CSR[2] =\r

                                ( 1 << 24)      |       // Delay between Consecutive Transfers (32 MCK periods)\r
                                ( 1 << 16)      |       // Delay Before SPCK (1 MCK period)\r
                                ( 6 << 8)       |       // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud\r
                                ( 1 << 24)      |       // Delay between Consecutive Transfers (32 MCK periods)\r
                                ( 1 << 16)      |       // Delay Before SPCK (1 MCK period)\r
                                ( 6 << 8)       |       // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud\r


@@ -77,7 +79,7 @@ void SetupSpi(int mode)
                                ( 0 << 0);              // Clock Polarity inactive state is logic 0\r
                        break;\r
                default:                                // Disable SPI\r
                                ( 0 << 0);              // Clock Polarity inactive state is logic 0\r
                        break;\r
                default:                                // Disable SPI\r

-                       SPI_CONTROL = SPI_CONTROL_DISABLE;\r
+                       AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIDIS;\r

                        break;\r
        }\r
 }\r
                        break;\r
        }\r
 }\r


@@ -89,35 +91,36 @@ void SetupSpi(int mode)
 void FpgaSetupSsc(void)\r
 {\r
        // First configure the GPIOs, and get ourselves a clock.\r
 void FpgaSetupSsc(void)\r
 {\r
        // First configure the GPIOs, and get ourselves a clock.\r

-       PIO_PERIPHERAL_A_SEL =  (1 << GPIO_SSC_FRAME)   |\r
-                                                       (1 << GPIO_SSC_DIN)             |\r
-                                                       (1 << GPIO_SSC_DOUT)    |\r
-                                                       (1 << GPIO_SSC_CLK);\r
-       PIO_DISABLE = (1 << GPIO_SSC_DOUT);\r
+       AT91C_BASE_PIOA->PIO_ASR =\r
+               GPIO_SSC_FRAME  |\r
+               GPIO_SSC_DIN    |\r
+               GPIO_SSC_DOUT   |\r
+               GPIO_SSC_CLK;\r
+       AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DOUT;\r

 \r
 \r

-       PMC_PERIPHERAL_CLK_ENABLE = (1 << PERIPH_SSC);\r
+       AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_SSC);\r

 \r
        // Now set up the SSC proper, starting from a known state.\r
 \r
        // Now set up the SSC proper, starting from a known state.\r

-       SSC_CONTROL = SSC_CONTROL_RESET;\r
+       AT91C_BASE_SSC->SSC_CR = AT91C_SSC_SWRST;\r

 \r
        // RX clock comes from TX clock, RX starts when TX starts, data changes\r
        // on RX clock rising edge, sampled on falling edge\r
 \r
        // RX clock comes from TX clock, RX starts when TX starts, data changes\r
        // on RX clock rising edge, sampled on falling edge\r

-       SSC_RECEIVE_CLOCK_MODE = SSC_CLOCK_MODE_SELECT(1) | SSC_CLOCK_MODE_START(1);\r
+       AT91C_BASE_SSC->SSC_RCMR = SSC_CLOCK_MODE_SELECT(1) | SSC_CLOCK_MODE_START(1);\r

 \r
        // 8 bits per transfer, no loopback, MSB first, 1 transfer per sync\r
        // pulse, no output sync, start on positive-going edge of sync\r
 \r
        // 8 bits per transfer, no loopback, MSB first, 1 transfer per sync\r
        // pulse, no output sync, start on positive-going edge of sync\r

-       SSC_RECEIVE_FRAME_MODE = SSC_FRAME_MODE_BITS_IN_WORD(8) |\r
-               SSC_FRAME_MODE_MSB_FIRST | SSC_FRAME_MODE_WORDS_PER_TRANSFER(0);\r
+       AT91C_BASE_SSC->SSC_RFMR = SSC_FRAME_MODE_BITS_IN_WORD(8) |\r
+               AT91C_SSC_MSBF | SSC_FRAME_MODE_WORDS_PER_TRANSFER(0);\r

 \r
        // clock comes from TK pin, no clock output, outputs change on falling\r
        // edge of TK, start on rising edge of TF\r
 \r
        // clock comes from TK pin, no clock output, outputs change on falling\r
        // edge of TK, start on rising edge of TF\r

-       SSC_TRANSMIT_CLOCK_MODE = SSC_CLOCK_MODE_SELECT(2) |\r
+       AT91C_BASE_SSC->SSC_TCMR = SSC_CLOCK_MODE_SELECT(2) |\r

                SSC_CLOCK_MODE_START(5);\r
 \r
        // tx framing is the same as the rx framing\r
                SSC_CLOCK_MODE_START(5);\r
 \r
        // tx framing is the same as the rx framing\r

-       SSC_TRANSMIT_FRAME_MODE = SSC_RECEIVE_FRAME_MODE;\r
+       AT91C_BASE_SSC->SSC_TFMR = AT91C_BASE_SSC->SSC_RFMR;\r

 \r
 \r

-       SSC_CONTROL = SSC_CONTROL_RX_ENABLE | SSC_CONTROL_TX_ENABLE;\r
+       AT91C_BASE_SSC->SSC_CR = AT91C_SSC_RXEN | AT91C_SSC_TXEN;\r

 }\r
 \r
 //-----------------------------------------------------------------------------\r
 }\r
 \r
 //-----------------------------------------------------------------------------\r


@@ -128,11 +131,11 @@ void FpgaSetupSsc(void)
 //-----------------------------------------------------------------------------\r
 void FpgaSetupSscDma(BYTE *buf, int len)\r
 {\r
 //-----------------------------------------------------------------------------\r
 void FpgaSetupSscDma(BYTE *buf, int len)\r
 {\r

-       PDC_RX_POINTER(SSC_BASE) = (DWORD)buf;\r
-       PDC_RX_COUNTER(SSC_BASE) = len;\r
-       PDC_RX_NEXT_POINTER(SSC_BASE) = (DWORD)buf;\r
-       PDC_RX_NEXT_COUNTER(SSC_BASE) = len;\r
-       PDC_CONTROL(SSC_BASE) = PDC_RX_ENABLE;\r
+       AT91C_BASE_PDC_SSC->PDC_RPR = (DWORD)buf;\r
+       AT91C_BASE_PDC_SSC->PDC_RCR = len;\r
+       AT91C_BASE_PDC_SSC->PDC_RNPR = (DWORD)buf;\r
+       AT91C_BASE_PDC_SSC->PDC_RNCR = len;\r
+       AT91C_BASE_PDC_SSC->PDC_PTCR = AT91C_PDC_RXTEN;\r

 }\r
 \r
 static void DownloadFPGA_byte(unsigned char w)\r
 }\r
 \r
 static void DownloadFPGA_byte(unsigned char w)\r


@@ -154,8 +157,8 @@ static void DownloadFPGA(const char *FpgaImage, int FpgaImageLen, int byterevers
 {\r
        int i=0;\r
 \r
 {\r
        int i=0;\r
 \r

-       PIO_OUTPUT_ENABLE = (1 << GPIO_FPGA_ON);\r
-       PIO_ENABLE = (1 << GPIO_FPGA_ON);\r
+       AT91C_BASE_PIOA->PIO_OER = GPIO_FPGA_ON;\r
+       AT91C_BASE_PIOA->PIO_PER = GPIO_FPGA_ON;\r

        HIGH(GPIO_FPGA_ON);             // ensure everything is powered on\r
 \r
        SpinDelay(50);\r
        HIGH(GPIO_FPGA_ON);             // ensure everything is powered on\r
 \r
        SpinDelay(50);\r


@@ -163,20 +166,27 @@ static void DownloadFPGA(const char *FpgaImage, int FpgaImageLen, int byterevers
        LED_D_ON();\r
 \r
        // These pins are inputs\r
        LED_D_ON();\r
 \r
        // These pins are inputs\r

-    PIO_OUTPUT_DISABLE =     (1 << GPIO_FPGA_NINIT) | (1 << GPIO_FPGA_DONE);\r
+    AT91C_BASE_PIOA->PIO_ODR =\r
+       GPIO_FPGA_NINIT |\r
+       GPIO_FPGA_DONE;\r

        // PIO controls the following pins\r
        // PIO controls the following pins\r

-    PIO_ENABLE =             (1 << GPIO_FPGA_NINIT) | (1 << GPIO_FPGA_DONE);\r
+    AT91C_BASE_PIOA->PIO_PER =\r
+       GPIO_FPGA_NINIT |\r
+       GPIO_FPGA_DONE;\r

        // Enable pull-ups\r
        // Enable pull-ups\r

-       PIO_NO_PULL_UP_DISABLE = (1 << GPIO_FPGA_NINIT) | (1 << GPIO_FPGA_DONE);\r
+       AT91C_BASE_PIOA->PIO_PPUER =\r
+               GPIO_FPGA_NINIT |\r
+               GPIO_FPGA_DONE;\r

 \r
        // setup initial logic state\r
        HIGH(GPIO_FPGA_NPROGRAM);\r
        LOW(GPIO_FPGA_CCLK);\r
        LOW(GPIO_FPGA_DIN);\r
        // These pins are outputs\r
 \r
        // setup initial logic state\r
        HIGH(GPIO_FPGA_NPROGRAM);\r
        LOW(GPIO_FPGA_CCLK);\r
        LOW(GPIO_FPGA_DIN);\r
        // These pins are outputs\r

-       PIO_OUTPUT_ENABLE = (1 << GPIO_FPGA_NPROGRAM)   |\r
-                                               (1 << GPIO_FPGA_CCLK)           |\r
-                                               (1 << GPIO_FPGA_DIN);\r
+       AT91C_BASE_PIOA->PIO_OER =\r
+               GPIO_FPGA_NPROGRAM      |\r
+               GPIO_FPGA_CCLK          |\r
+               GPIO_FPGA_DIN;\r

 \r
        // enter FPGA configuration mode\r
        LOW(GPIO_FPGA_NPROGRAM);\r
 \r
        // enter FPGA configuration mode\r
        LOW(GPIO_FPGA_NPROGRAM);\r


@@ -185,7 +195,7 @@ static void DownloadFPGA(const char *FpgaImage, int FpgaImageLen, int byterevers
 \r
        i=100000;\r
        // wait for FPGA ready to accept data signal\r
 \r
        i=100000;\r
        // wait for FPGA ready to accept data signal\r

-       while ((i) && ( !(PIO_PIN_DATA_STATUS & (1<<GPIO_FPGA_NINIT) ) ) ) {\r
+       while ((i) && ( !(AT91C_BASE_PIOA->PIO_PDSR & GPIO_FPGA_NINIT ) ) ) {\r

                i--;\r
        }\r
 \r
                i--;\r
        }\r
 \r


@@ -215,7 +225,7 @@ static void DownloadFPGA(const char *FpgaImage, int FpgaImageLen, int byterevers
 \r
        // continue to clock FPGA until ready signal goes high\r
        i=100000;\r
 \r
        // continue to clock FPGA until ready signal goes high\r
        i=100000;\r

-       while ( (i--) && ( !(PIO_PIN_DATA_STATUS & (1<<GPIO_FPGA_DONE) ) ) ) {\r
+       while ( (i--) && ( !(AT91C_BASE_PIOA->PIO_PDSR & GPIO_FPGA_DONE ) ) ) {\r

                HIGH(GPIO_FPGA_CCLK);\r
                LOW(GPIO_FPGA_CCLK);\r
        }\r
                HIGH(GPIO_FPGA_CCLK);\r
                LOW(GPIO_FPGA_CCLK);\r
        }\r


@@ -235,7 +245,7 @@ static int bitparse_initialized;
  * 00 09 0f f0 0f f0 0f f0 0f f0 00 00 01\r
  * After that the format is 1 byte section type (ASCII character), 2 byte length\r
  * (big endian), <length> bytes content. Except for section 'e' which has 4 bytes\r
  * 00 09 0f f0 0f f0 0f f0 0f f0 00 00 01\r
  * After that the format is 1 byte section type (ASCII character), 2 byte length\r
  * (big endian), <length> bytes content. Except for section 'e' which has 4 bytes\r

- * length.
+ * length.\r

  */\r
 static const char _bitparse_fixed_header[] = {0x00, 0x09, 0x0f, 0xf0, 0x0f, 0xf0, 0x0f, 0xf0, 0x0f, 0xf0, 0x00, 0x00, 0x01};\r
 static int bitparse_init(void * start_address, void *end_address)\r
  */\r
 static const char _bitparse_fixed_header[] = {0x00, 0x09, 0x0f, 0xf0, 0x0f, 0xf0, 0x0f, 0xf0, 0x0f, 0xf0, 0x00, 0x00, 0x01};\r
 static int bitparse_init(void * start_address, void *end_address)\r


@@ -303,11 +313,11 @@ int bitparse_find_section(char section_name, char **section_start, unsigned int
 extern char _binary_fpga_bit_start, _binary_fpga_bit_end;\r
 void FpgaDownloadAndGo(void)\r
 {\r
 extern char _binary_fpga_bit_start, _binary_fpga_bit_end;\r
 void FpgaDownloadAndGo(void)\r
 {\r

-       /* Check for the new flash image format: Should have the .bit file at &_binary_fpga_bit_start
+       /* Check for the new flash image format: Should have the .bit file at &_binary_fpga_bit_start\r

         */\r
        if(bitparse_init(&_binary_fpga_bit_start, &_binary_fpga_bit_end)) {\r
                /* Successfully initialized the .bit parser. Find the 'e' section and\r
         */\r
        if(bitparse_init(&_binary_fpga_bit_start, &_binary_fpga_bit_end)) {\r
                /* Successfully initialized the .bit parser. Find the 'e' section and\r

-                * send its contents to the FPGA.
+                * send its contents to the FPGA.\r

                 */\r
                char *bitstream_start;\r
                unsigned int bitstream_length;\r
                 */\r
                char *bitstream_start;\r
                unsigned int bitstream_length;\r


@@ -323,7 +333,7 @@ void FpgaDownloadAndGo(void)
         * = 10,524 DWORDs, stored as DWORDS e.g. little-endian in memory, but each DWORD\r
         * is still to be transmitted in MSBit first order. Set the invert flag to indicate\r
         * that the DownloadFPGA function should invert every 4 byte sequence when doing\r
         * = 10,524 DWORDs, stored as DWORDS e.g. little-endian in memory, but each DWORD\r
         * is still to be transmitted in MSBit first order. Set the invert flag to indicate\r
         * that the DownloadFPGA function should invert every 4 byte sequence when doing\r

-        * the bytewise download.
+        * the bytewise download.\r

         */\r
        if( *(DWORD*)0x102000 == 0xFFFFFFFF && *(DWORD*)0x102004 == 0xAA995566 )\r
                DownloadFPGA((char*)0x102000, 10524*4, 1);\r
         */\r
        if( *(DWORD*)0x102000 == 0xFFFFFFFF && *(DWORD*)0x102004 == 0xAA995566 )\r
                DownloadFPGA((char*)0x102000, 10524*4, 1);\r


@@ -368,8 +378,8 @@ void FpgaGatherVersion(char *dst, int len)
 void FpgaSendCommand(WORD cmd, WORD v)\r
 {\r
        SetupSpi(SPI_FPGA_MODE);\r
 void FpgaSendCommand(WORD cmd, WORD v)\r
 {\r
        SetupSpi(SPI_FPGA_MODE);\r

-       while ((SPI_STATUS & SPI_STATUS_TX_EMPTY) == 0);                // wait for the transfer to complete\r
-       SPI_TX_DATA = SPI_CONTROL_LAST_TRANSFER | cmd | v;              // send the data\r
+       while ((AT91C_BASE_SPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0);              // wait for the transfer to complete\r
+       AT91C_BASE_SPI->SPI_TDR = AT91C_SPI_LASTXFER | cmd | v;         // send the data\r

 }\r
 //-----------------------------------------------------------------------------\r
 // Write the FPGA setup word (that determines what mode the logic is in, read\r
 }\r
 //-----------------------------------------------------------------------------\r
 // Write the FPGA setup word (that determines what mode the logic is in, read\r


@@ -386,17 +396,19 @@ void FpgaWriteConfWord(BYTE v)
 // closable, but should only close one at a time. Not an FPGA thing, but\r
 // the samples from the ADC always flow through the FPGA.\r
 //-----------------------------------------------------------------------------\r
 // closable, but should only close one at a time. Not an FPGA thing, but\r
 // the samples from the ADC always flow through the FPGA.\r
 //-----------------------------------------------------------------------------\r

-void SetAdcMuxFor(int whichGpio)\r
+void SetAdcMuxFor(DWORD whichGpio)\r

 {\r
 {\r

-       PIO_OUTPUT_ENABLE = (1 << GPIO_MUXSEL_HIPKD) |\r
-                                               (1 << GPIO_MUXSEL_LOPKD) |\r
-                                               (1 << GPIO_MUXSEL_LORAW) |\r
-                                               (1 << GPIO_MUXSEL_HIRAW);\r
-\r
-       PIO_ENABLE              =       (1 << GPIO_MUXSEL_HIPKD) |\r
-                                               (1 << GPIO_MUXSEL_LOPKD) |\r
-                                               (1 << GPIO_MUXSEL_LORAW) |\r
-                                               (1 << GPIO_MUXSEL_HIRAW);\r
+       AT91C_BASE_PIOA->PIO_OER =\r
+               GPIO_MUXSEL_HIPKD |\r
+               GPIO_MUXSEL_LOPKD |\r
+               GPIO_MUXSEL_LORAW |\r
+               GPIO_MUXSEL_HIRAW;\r
+\r
+       AT91C_BASE_PIOA->PIO_PER =\r
+               GPIO_MUXSEL_HIPKD |\r
+               GPIO_MUXSEL_LOPKD |\r
+               GPIO_MUXSEL_LORAW |\r
+               GPIO_MUXSEL_HIRAW;\r

 \r
        LOW(GPIO_MUXSEL_HIPKD);\r
        LOW(GPIO_MUXSEL_HIRAW);\r
 \r
        LOW(GPIO_MUXSEL_HIPKD);\r
        LOW(GPIO_MUXSEL_HIRAW);\r