X-Git-Url: http://cvs.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/07c808038c48a74842290084d1217d6f69cbf18e..fabef615ec2fbe1fbe4b69af9482931e781d8d08:/armsrc/lfops.c?ds=sidebyside diff --git a/armsrc/lfops.c b/armsrc/lfops.c index b9dbb8e2..ab86f931 100644 --- a/armsrc/lfops.c +++ b/armsrc/lfops.c @@ -15,147 +15,69 @@ #include "crc16.h" #include "string.h" #include "lfdemod.h" +#include "lfsampling.h" +#include "protocols.h" +#include "usb_cdc.h" // for usb_poll_validate_length +#ifndef SHORT_COIL +# define SHORT_COIL() LOW(GPIO_SSC_DOUT) +#endif +#ifndef OPEN_COIL +# define OPEN_COIL() HIGH(GPIO_SSC_DOUT) +#endif /** -* Does the sample acquisition. If threshold is specified, the actual sampling -* is not commenced until the threshold has been reached. -* @param trigger_threshold - the threshold -* @param silent - is true, now outputs are made. If false, dbprints the status -*/ -void DoAcquisition125k_internal(int trigger_threshold,bool silent) -{ - uint8_t *dest = (uint8_t *)BigBuf; - int n = sizeof(BigBuf); - int i; - - memset(dest, 0, n); - i = 0; - for(;;) { - if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) { - AT91C_BASE_SSC->SSC_THR = 0x43; - LED_D_ON(); - } - if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { - dest[i] = (uint8_t)AT91C_BASE_SSC->SSC_RHR; - LED_D_OFF(); - if (trigger_threshold != -1 && dest[i] < trigger_threshold) - continue; - else - trigger_threshold = -1; - if (++i >= n) break; - } - } - if(!silent) - { - Dbprintf("buffer samples: %02x %02x %02x %02x %02x %02x %02x %02x ...", - dest[0], dest[1], dest[2], dest[3], dest[4], dest[5], dest[6], dest[7]); - - } -} -/** -* Perform sample aquisition. -*/ -void DoAcquisition125k(int trigger_threshold) -{ - DoAcquisition125k_internal(trigger_threshold, false); -} - -/** -* Setup the FPGA to listen for samples. This method downloads the FPGA bitstream -* if not already loaded, sets divisor and starts up the antenna. -* @param divisor : 1, 88> 255 or negative ==> 134.8 KHz -* 0 or 95 ==> 125 KHz -* -**/ -void LFSetupFPGAForADC(int divisor, bool lf_field) -{ - FpgaDownloadAndGo(FPGA_BITSTREAM_LF); - if ( (divisor == 1) || (divisor < 0) || (divisor > 255) ) - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz - else if (divisor == 0) - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - else - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor); - - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | (lf_field ? FPGA_LF_ADC_READER_FIELD : 0)); - - // Connect the A/D to the peak-detected low-frequency path. - SetAdcMuxFor(GPIO_MUXSEL_LOPKD); - // Give it a bit of time for the resonant antenna to settle. - SpinDelay(50); - // Now set up the SSC to get the ADC samples that are now streaming at us. - FpgaSetupSsc(); -} -/** -* Initializes the FPGA, and acquires the samples. -**/ -void AcquireRawAdcSamples125k(int divisor) -{ - LFSetupFPGAForADC(divisor, true); - // Now call the acquisition routine - DoAcquisition125k_internal(-1,false); -} -/** -* Initializes the FPGA for snoop-mode, and acquires the samples. -**/ - -void SnoopLFRawAdcSamples(int divisor, int trigger_threshold) -{ - LFSetupFPGAForADC(divisor, false); - DoAcquisition125k(trigger_threshold); -} - -void ModThenAcquireRawAdcSamples125k(int delay_off, int period_0, int period_1, uint8_t *command) + * Function to do a modulation and then get samples. + * @param delay_off + * @param periods 0xFFFF0000 is period_0, 0x0000FFFF is period_1 + * @param useHighFreg + * @param command + */ +void ModThenAcquireRawAdcSamples125k(uint32_t delay_off, uint32_t periods, uint32_t useHighFreq, uint8_t *command) { - /* Make sure the tag is reset */ FpgaDownloadAndGo(FPGA_BITSTREAM_LF); FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - SpinDelay(2500); - - - int divisor_used = 95; // 125 KHz - // see if 'h' was specified + SpinDelay(200); - if (command[strlen((char *) command) - 1] == 'h') - divisor_used = 88; // 134.8 KHz + uint16_t period_0 = periods >> 16; + uint16_t period_1 = periods & 0xFFFF; + + // 95 == 125 KHz 88 == 124.8 KHz + int divisor_used = (useHighFreq) ? 88 : 95; + sample_config sc = { 0,0,1, divisor_used, 0}; + setSamplingConfig(&sc); + //clear read buffer + BigBuf_Clear_keep_EM(); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor_used); - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); - // Give it a bit of time for the resonant antenna to settle. - SpinDelay(50); + LFSetupFPGAForADC(sc.divisor, 1); // And a little more time for the tag to fully power up - SpinDelay(2000); - - // Now set up the SSC to get the ADC samples that are now streaming at us. - FpgaSetupSsc(); + SpinDelay(50); // now modulate the reader field while(*command != '\0' && *command != ' ') { FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); LED_D_OFF(); - SpinDelayUs(delay_off); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor_used); + WaitUS(delay_off); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor); FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); LED_D_ON(); if(*(command++) == '0') - SpinDelayUs(period_0); + WaitUS(period_0); else - SpinDelayUs(period_1); + WaitUS(period_1); } FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); LED_D_OFF(); - SpinDelayUs(delay_off); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor_used); - + WaitUS(delay_off); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor); FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); // now do the read - DoAcquisition125k(-1); + DoAcquisition_config(false); } /* blank r/w tag data stream @@ -173,12 +95,12 @@ void ReadTItag(void) // when we read a TI tag we sample the zerocross line at 2Mhz // TI tags modulate a 1 as 16 cycles of 123.2Khz // TI tags modulate a 0 as 16 cycles of 134.2Khz - #define FSAMPLE 2000000 - #define FREQLO 123200 - #define FREQHI 134200 + #define FSAMPLE 2000000 + #define FREQLO 123200 + #define FREQHI 134200 - signed char *dest = (signed char *)BigBuf; - int n = sizeof(BigBuf); + signed char *dest = (signed char *)BigBuf_get_addr(); + uint16_t n = BigBuf_max_traceLen(); // 128 bit shift register [shift3:shift2:shift1:shift0] uint32_t shift3 = 0, shift2 = 0, shift1 = 0, shift0 = 0; @@ -287,8 +209,7 @@ void ReadTItag(void) crc = update_crc16(crc, (shift1>>16)&0xff); crc = update_crc16(crc, (shift1>>24)&0xff); - Dbprintf("Info: Tag data: %x%08x, crc=%x", - (unsigned int)shift1, (unsigned int)shift0, (unsigned int)shift2 & 0xFFFF); + Dbprintf("Info: Tag data: %x%08x, crc=%x", (unsigned int)shift1, (unsigned int)shift0, (unsigned int)shift2 & 0xFFFF); if (crc != (shift2&0xffff)) { Dbprintf("Error: CRC mismatch, expected %x", (unsigned int)crc); } else { @@ -304,20 +225,20 @@ void WriteTIbyte(uint8_t b) // modulate 8 bits out to the antenna for (i=0; i<8; i++) { - if (b&(1<PIO_PDR = GPIO_SSC_DIN; @@ -351,7 +275,7 @@ void AcquireTiType(void) AT91C_BASE_SSC->SSC_RFMR = SSC_FRAME_MODE_BITS_IN_WORD(32) | AT91C_SSC_MSBF; AT91C_BASE_SSC->SSC_TCMR = 0; AT91C_BASE_SSC->SSC_TFMR = 0; - + // iceman, FpgaSetupSsc() ?? the code above? can it be replaced? LED_D_ON(); // modulate antenna @@ -368,7 +292,7 @@ void AcquireTiType(void) i = 0; for(;;) { if(AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { - BigBuf[i] = AT91C_BASE_SSC->SSC_RHR; // store 32 bit values in buffer + buf[i] = AT91C_BASE_SSC->SSC_RHR; // store 32 bit values in buffer i++; if(i >= TIBUFLEN) break; } WDT_HIT(); @@ -378,12 +302,13 @@ void AcquireTiType(void) AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DOUT; AT91C_BASE_PIOA->PIO_ASR = GPIO_SSC_DIN | GPIO_SSC_DOUT; - char *dest = (char *)BigBuf; - n = TIBUFLEN*32; + char *dest = (char *)BigBuf_get_addr(); + n = TIBUFLEN * 32; + // unpack buffer - for (i=TIBUFLEN-1; i>=0; i--) { - for (j=0; j<32; j++) { - if(BigBuf[i] & (1 << j)) { + for (i = TIBUFLEN-1; i >= 0; i--) { + for (j = 0; j < 32; j++) { + if(buf[i] & (1 << j)) { dest[--n] = 1; } else { dest[--n] = -1; @@ -408,8 +333,7 @@ void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc) crc = update_crc16(crc, (idhi>>16)&0xff); crc = update_crc16(crc, (idhi>>24)&0xff); } - Dbprintf("Writing to tag: %x%08x, crc=%x", - (unsigned int) idhi, (unsigned int) idlo, crc); + Dbprintf("Writing to tag: %x%08x, crc=%x", (unsigned int) idhi, (unsigned int) idlo, crc); // TI tags charge at 134.2Khz FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz @@ -431,7 +355,7 @@ void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc) // start by writing 0xBB (keyword) and 0xEB (password) // then write 80 bits of data (or 64 bit data + 16 bit crc if you prefer) // finally end with 0x0300 (write frame) - // all data is sent lsb firts + // all data is sent lsb first // finish with 15ms programming time // modulate antenna @@ -461,60 +385,59 @@ void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc) AcquireTiType(); FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - DbpString("Now use tiread to check"); + DbpString("Now use `lf ti read` to check"); } void SimulateTagLowFrequency(int period, int gap, int ledcontrol) { - int i; - uint8_t *tab = (uint8_t *)BigBuf; + int i = 0; + uint8_t *tab = BigBuf_get_addr(); - FpgaDownloadAndGo(FPGA_BITSTREAM_LF); - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT); + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT | FPGA_LF_EDGE_DETECT_READER_FIELD); AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT | GPIO_SSC_CLK; - AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT; AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_CLK; -#define SHORT_COIL() LOW(GPIO_SSC_DOUT) -#define OPEN_COIL() HIGH(GPIO_SSC_DOUT) - - i = 0; for(;;) { + WDT_HIT(); + + if (ledcontrol) LED_D_ON(); + + //wait until SSC_CLK goes HIGH while(!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK)) { - if(BUTTON_PRESS()) { - DbpString("Stopped"); - return; - } WDT_HIT(); + if ( usb_poll_validate_length() || BUTTON_PRESS() ) { + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + LED_D_OFF(); + return; + } } - - if (ledcontrol) - LED_D_ON(); - + if(tab[i]) OPEN_COIL(); else SHORT_COIL(); - if (ledcontrol) - LED_D_OFF(); - + if (ledcontrol) LED_D_OFF(); + + //wait until SSC_CLK goes LOW while(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK) { - if(BUTTON_PRESS()) { - DbpString("Stopped"); - return; - } WDT_HIT(); + if ( usb_poll_validate_length() || BUTTON_PRESS() ) { + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + LED_D_OFF(); + return; + } } i++; if(i == period) { i = 0; if (gap) { + WDT_HIT(); SHORT_COIL(); - SpinDelayUs(gap); + WaitUS(gap); } } } @@ -525,29 +448,31 @@ void SimulateTagLowFrequencyBidir(int divisor, int t0) { } -// compose fc/8 fc/10 waveform -static void fc(int c, int *n) { - uint8_t *dest = (uint8_t *)BigBuf; +// compose fc/8 fc/10 waveform (FSK2) +static void fc(int c, int *n) +{ + uint8_t *dest = BigBuf_get_addr(); int idx; // for when we want an fc8 pattern every 4 logical bits if(c==0) { dest[((*n)++)]=1; dest[((*n)++)]=1; - dest[((*n)++)]=0; - dest[((*n)++)]=0; + dest[((*n)++)]=1; + dest[((*n)++)]=1; dest[((*n)++)]=0; dest[((*n)++)]=0; dest[((*n)++)]=0; dest[((*n)++)]=0; } - // an fc/8 encoded bit is a bit pattern of 11000000 x6 = 48 samples + + // an fc/8 encoded bit is a bit pattern of 11110000 x6 = 48 samples if(c==8) { for (idx=0; idx<6; idx++) { dest[((*n)++)]=1; dest[((*n)++)]=1; - dest[((*n)++)]=0; - dest[((*n)++)]=0; + dest[((*n)++)]=1; + dest[((*n)++)]=1; dest[((*n)++)]=0; dest[((*n)++)]=0; dest[((*n)++)]=0; @@ -555,9 +480,11 @@ static void fc(int c, int *n) { } } - // an fc/10 encoded bit is a bit pattern of 1110000000 x5 = 50 samples + // an fc/10 encoded bit is a bit pattern of 1111100000 x5 = 50 samples if(c==10) { for (idx=0; idx<5; idx++) { + dest[((*n)++)]=1; + dest[((*n)++)]=1; dest[((*n)++)]=1; dest[((*n)++)]=1; dest[((*n)++)]=1; @@ -566,17 +493,48 @@ static void fc(int c, int *n) { dest[((*n)++)]=0; dest[((*n)++)]=0; dest[((*n)++)]=0; - dest[((*n)++)]=0; - dest[((*n)++)]=0; } } } +// compose fc/X fc/Y waveform (FSKx) +static void fcAll(uint8_t fc, int *n, uint8_t clock, uint16_t *modCnt) +{ + uint8_t *dest = BigBuf_get_addr(); + uint8_t halfFC = fc/2; + uint8_t wavesPerClock = clock/fc; + uint8_t mod = clock % fc; //modifier + uint8_t modAdj = fc/mod; //how often to apply modifier + bool modAdjOk = !(fc % mod); //if (fc % mod==0) modAdjOk=TRUE; + // loop through clock - step field clock + for (uint8_t idx=0; idx < wavesPerClock; idx++){ + // put 1/2 FC length 1's and 1/2 0's per field clock wave (to create the wave) + memset(dest+(*n), 0, fc-halfFC); //in case of odd number use extra here + memset(dest+(*n)+(fc-halfFC), 1, halfFC); + *n += fc; + } + if (mod>0) (*modCnt)++; + if ((mod>0) && modAdjOk){ //fsk2 + if ((*modCnt % modAdj) == 0){ //if 4th 8 length wave in a rf/50 add extra 8 length wave + memset(dest+(*n), 0, fc-halfFC); + memset(dest+(*n)+(fc-halfFC), 1, halfFC); + *n += fc; + } + } + if (mod>0 && !modAdjOk){ //fsk1 + memset(dest+(*n), 0, mod-(mod/2)); + memset(dest+(*n)+(mod-(mod/2)), 1, mod/2); + *n += mod; + } +} // prepare a waveform pattern in the buffer based on the ID given then // simulate a HID tag until the button is pressed void CmdHIDsimTAG(int hi, int lo, int ledcontrol) { - int n=0, i=0; + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + set_tracing(FALSE); + + int n = 0, i = 0; /* HID tag bitstream format The tag contains a 44bit unique code. This is sent out MSB first in sets of 4 bits @@ -587,13 +545,13 @@ void CmdHIDsimTAG(int hi, int lo, int ledcontrol) nor 1 bits, they are special patterns (a = set of 12 fc8 and b = set of 10 fc10) */ - if (hi>0xFFF) { - DbpString("Tags can only have 44 bits."); + if (hi > 0xFFF) { + DbpString("Tags can only have 44 bits. - USE lf simfsk for larger tags"); return; } fc(0,&n); // special start of frame marker containing invalid bit sequences - fc(8, &n); fc(8, &n); // invalid + fc(8, &n); fc(8, &n); // invalid fc(8, &n); fc(10, &n); // logical 0 fc(10, &n); fc(10, &n); // invalid fc(8, &n); fc(10, &n); // logical 0 @@ -603,9 +561,9 @@ void CmdHIDsimTAG(int hi, int lo, int ledcontrol) for (i=11; i>=0; i--) { if ((i%4)==3) fc(0,&n); if ((hi>>i)&1) { - fc(10, &n); fc(8, &n); // low-high transition + fc(10, &n); fc(8, &n); // low-high transition } else { - fc(8, &n); fc(10, &n); // high-low transition + fc(8, &n); fc(10, &n); // high-low transition } } @@ -614,53 +572,228 @@ void CmdHIDsimTAG(int hi, int lo, int ledcontrol) for (i=31; i>=0; i--) { if ((i%4)==3) fc(0,&n); if ((lo>>i)&1) { - fc(10, &n); fc(8, &n); // low-high transition + fc(10, &n); fc(8, &n); // low-high transition } else { - fc(8, &n); fc(10, &n); // high-low transition + fc(8, &n); fc(10, &n); // high-low transition + } + } + WDT_HIT(); + + if (ledcontrol) LED_A_ON(); + SimulateTagLowFrequency(n, 0, ledcontrol); + if (ledcontrol) LED_A_OFF(); +} + +// prepare a waveform pattern in the buffer based on the ID given then +// simulate a FSK tag until the button is pressed +// arg1 contains fcHigh and fcLow, arg2 contains invert and clock +void CmdFSKsimTAG(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream) +{ + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + + // free eventually allocated BigBuf memory + BigBuf_free(); BigBuf_Clear_ext(false); + clear_trace(); + set_tracing(FALSE); + + int ledcontrol = 1, n = 0, i = 0; + uint8_t fcHigh = arg1 >> 8; + uint8_t fcLow = arg1 & 0xFF; + uint16_t modCnt = 0; + uint8_t clk = arg2 & 0xFF; + uint8_t invert = (arg2 >> 8) & 1; + + for (i=0; i> 8) & 0xFF; + uint8_t encoding = arg1 & 0xFF; + uint8_t separator = arg2 & 1; + uint8_t invert = (arg2 >> 8) & 1; + + if (encoding == 2){ //biphase + uint8_t phase = 0; + for (i=0; i> 8; + uint8_t carrier = arg1 & 0xFF; + uint8_t invert = arg2 & 0xFF; + uint8_t curPhase = 0; + for (i=0; i0 && lo>0){ - // final loop, go over previously decoded manchester data and decode into usable tag ID - // 111000 bit pattern represent start of frame, 01 pattern represents a 1 and 10 represents a 0 - if (hi2 != 0){ //extra large HID tags + size = 50*128*2; //big enough to catch 2 sequences of largest format + idx = HIDdemodFSK(dest, &size, &hi2, &hi, &lo); + + if (idx>0 && lo>0 && (size==96 || size==192)){ + // go over previously decoded manchester data and decode into usable tag ID + if (hi2 != 0){ //extra large HID tags 88/192 bits Dbprintf("TAG ID: %x%08x%08x (%d)", - (unsigned int) hi2, (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); - }else { //standard HID tags <38 bits - //Dbprintf("TAG ID: %x%08x (%d)",(unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); //old print cmd + (unsigned int) hi2, + (unsigned int) hi, + (unsigned int) lo, + (unsigned int) (lo>>1) & 0xFFFF + ); + } else { //standard HID tags 44/96 bits uint8_t bitlen = 0; uint32_t fc = 0; uint32_t cardnum = 0; + if (((hi>>5)&1) == 1){//if bit 38 is set then < 37 bit format is used uint32_t lo2=0; lo2=(((hi & 31) << 12) | (lo>>20)); //get bits 21-37 to check for format len bit @@ -698,19 +831,126 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) fc = ((hi&0xF)<<12)|(lo>>20); } } - //Dbprintf("TAG ID: %x%08x (%d)", - // (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); Dbprintf("TAG ID: %x%08x (%d) - Format Len: %dbit - FC: %d - Card: %d", - (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF, - (unsigned int) bitlen, (unsigned int) fc, (unsigned int) cardnum); + (unsigned int) hi, + (unsigned int) lo, + (unsigned int) (lo>>1) & 0xFFFF, + (unsigned int) bitlen, + (unsigned int) fc, + (unsigned int) cardnum); } if (findone){ if (ledcontrol) LED_A_OFF(); + *high = hi; + *low = lo; return; } // reset - hi2 = hi = lo = 0; } + hi2 = hi = lo = idx = 0; + WDT_HIT(); + } + DbpString("Stopped"); + if (ledcontrol) LED_A_OFF(); +} + +// loop to get raw HID waveform then FSK demodulate the TAG ID from it +void CmdAWIDdemodFSK(int findone, int *high, int *low, int ledcontrol) +{ + uint8_t *dest = BigBuf_get_addr(); + size_t size; + int idx=0; + //clear read buffer + BigBuf_Clear_keep_EM(); + // Configure to go in 125Khz listen mode + LFSetupFPGAForADC(95, true); + + while(!BUTTON_PRESS() && !usb_poll_validate_length()) { + + WDT_HIT(); + if (ledcontrol) LED_A_ON(); + + DoAcquisition_default(-1,true); + // FSK demodulator + size = 50*128*2; //big enough to catch 2 sequences of largest format + idx = AWIDdemodFSK(dest, &size); + + if (idx<=0 || size!=96) continue; + // Index map + // 0 10 20 30 40 50 60 + // | | | | | | | + // 01234567 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 - to 96 + // ----------------------------------------------------------------------------- + // 00000001 000 1 110 1 101 1 011 1 101 1 010 0 000 1 000 1 010 0 001 0 110 1 100 0 000 1 000 1 + // premable bbb o bbb o bbw o fff o fff o ffc o ccc o ccc o ccc o ccc o ccc o wxx o xxx o xxx o - to 96 + // |---26 bit---| |-----117----||-------------142-------------| + // b = format bit len, o = odd parity of last 3 bits + // f = facility code, c = card number + // w = wiegand parity + // (26 bit format shown) + + //get raw ID before removing parities + uint32_t rawLo = bytebits_to_byte(dest+idx+64,32); + uint32_t rawHi = bytebits_to_byte(dest+idx+32,32); + uint32_t rawHi2 = bytebits_to_byte(dest+idx,32); + + size = removeParity(dest, idx+8, 4, 1, 88); + if (size != 66) continue; + + // Index map + // 0 10 20 30 40 50 60 + // | | | | | | | + // 01234567 8 90123456 7890123456789012 3 456789012345678901234567890123456 + // ----------------------------------------------------------------------------- + // 00011010 1 01110101 0000000010001110 1 000000000000000000000000000000000 + // bbbbbbbb w ffffffff cccccccccccccccc w xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx + // |26 bit| |-117--| |-----142------| + // + // 00110010 0 0000011111010000000000000001000100101000100001111 0 00000000 + // bbbbbbbb w ffffffffffffffffccccccccccccccccccccccccccccccccc w xxxxxxxx + // |50 bit| |----4000------||-----------2248975-------------| + // + // b = format bit len, o = odd parity of last 3 bits + // f = facility code, c = card number + // w = wiegand parity + + uint32_t fc = 0; + uint32_t cardnum = 0; + uint32_t code1 = 0; + uint32_t code2 = 0; + uint8_t fmtLen = bytebits_to_byte(dest,8); + switch(fmtLen) { + case 26: + fc = bytebits_to_byte(dest + 9, 8); + cardnum = bytebits_to_byte(dest + 17, 16); + code1 = bytebits_to_byte(dest + 8,fmtLen); + Dbprintf("AWID Found - BitLength: %d, FC: %d, Card: %u - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, fc, cardnum, code1, rawHi2, rawHi, rawLo); + break; + case 50: + fc = bytebits_to_byte(dest + 9, 16); + cardnum = bytebits_to_byte(dest + 25, 32); + code1 = bytebits_to_byte(dest + 8, (fmtLen-32) ); + code2 = bytebits_to_byte(dest + 8 + (fmtLen-32), 32); + Dbprintf("AWID Found - BitLength: %d, FC: %d, Card: %u - Wiegand: %x%08x, Raw: %08x%08x%08x", fmtLen, fc, cardnum, code1, code2, rawHi2, rawHi, rawLo); + break; + default: + if (fmtLen > 32 ) { + cardnum = bytebits_to_byte(dest+8+(fmtLen-17), 16); + code1 = bytebits_to_byte(dest+8,fmtLen-32); + code2 = bytebits_to_byte(dest+8+(fmtLen-32),32); + Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%u) - Wiegand: %x%08x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, code2, rawHi2, rawHi, rawLo); + } else { + cardnum = bytebits_to_byte(dest+8+(fmtLen-17), 16); + code1 = bytebits_to_byte(dest+8,fmtLen); + Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%u) - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, rawHi2, rawHi, rawLo); + } + break; + } + if (findone){ + if (ledcontrol) LED_A_OFF(); + return; + } + idx = 0; WDT_HIT(); } DbpString("Stopped"); @@ -719,51 +959,60 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) void CmdEM410xdemod(int findone, int *high, int *low, int ledcontrol) { - uint8_t *dest = (uint8_t *)BigBuf; + uint8_t *dest = BigBuf_get_addr(); - size_t size=0; - int clk=0, invert=0, errCnt=0; + size_t size=0, idx=0; + int clk=0, invert=0, errCnt=0, maxErr=20; + uint32_t hi=0; uint64_t lo=0; + //clear read buffer + BigBuf_Clear_keep_EM(); // Configure to go in 125Khz listen mode LFSetupFPGAForADC(95, true); - while(!BUTTON_PRESS()) { + while(!BUTTON_PRESS() && !usb_poll_validate_length()) { WDT_HIT(); if (ledcontrol) LED_A_ON(); - DoAcquisition125k_internal(-1,true); - size = sizeof(BigBuf); - //Dbprintf("DEBUG: Buffer got"); + DoAcquisition_default(-1,true); + size = BigBuf_max_traceLen(); //askdemod and manchester decode - errCnt = askmandemod(dest, &size, &clk, &invert); - //Dbprintf("DEBUG: ASK Got"); + if (size > 16385) size = 16385; //big enough to catch 2 sequences of largest format + errCnt = askdemod(dest, &size, &clk, &invert, maxErr, 0, 1); WDT_HIT(); - if (errCnt>=0){ - lo = Em410xDecode(dest,size); - //Dbprintf("DEBUG: EM GOT"); - if (lo>0){ - Dbprintf("EM TAG ID: %02x%08x - (%05d_%03d_%08d)", - (uint32_t)(lo>>32), - (uint32_t)lo, - (uint32_t)(lo&0xFFFF), - (uint32_t)((lo>>16LL) & 0xFF), - (uint32_t)(lo & 0xFFFFFF)); - } + if (errCnt<0) continue; + + errCnt = Em410xDecode(dest, &size, &idx, &hi, &lo); + if (errCnt){ + if (size>64){ + Dbprintf("EM XL TAG ID: %06x%08x%08x - (%05d_%03d_%08d)", + hi, + (uint32_t)(lo>>32), + (uint32_t)lo, + (uint32_t)(lo&0xFFFF), + (uint32_t)((lo>>16LL) & 0xFF), + (uint32_t)(lo & 0xFFFFFF)); + } else { + Dbprintf("EM TAG ID: %02x%08x - (%05d_%03d_%08d)", + (uint32_t)(lo>>32), + (uint32_t)lo, + (uint32_t)(lo&0xFFFF), + (uint32_t)((lo>>16LL) & 0xFF), + (uint32_t)(lo & 0xFFFFFF)); + } + if (findone){ - if (ledcontrol) LED_A_OFF(); + if (ledcontrol) LED_A_OFF(); + *high=lo>>32; + *low=lo & 0xFFFFFFFF; return; } - } else{ - //Dbprintf("DEBUG: No Tag"); } WDT_HIT(); - lo = 0; - clk=0; - invert=0; - errCnt=0; - size=0; + hi = lo = size = idx = 0; + clk = invert = errCnt = 0; } DbpString("Stopped"); if (ledcontrol) LED_A_OFF(); @@ -771,23 +1020,29 @@ void CmdEM410xdemod(int findone, int *high, int *low, int ledcontrol) void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol) { - uint8_t *dest = (uint8_t *)BigBuf; + uint8_t *dest = BigBuf_get_addr(); int idx=0; uint32_t code=0, code2=0; uint8_t version=0; uint8_t facilitycode=0; uint16_t number=0; + uint8_t crc = 0; + uint16_t calccrc = 0; + + //clear read buffer + BigBuf_Clear_keep_EM(); + // Configure to go in 125Khz listen mode LFSetupFPGAForADC(95, true); - while(!BUTTON_PRESS()) { + while(!BUTTON_PRESS() && !usb_poll_validate_length()) { WDT_HIT(); if (ledcontrol) LED_A_ON(); - DoAcquisition125k_internal(-1,true); + DoAcquisition_default(-1,true); //fskdemod and get start index WDT_HIT(); - idx = IOdemodFSK(dest,sizeof(BigBuf)); - if (idx>0){ + idx = IOdemodFSK(dest, BigBuf_max_traceLen()); + if (idx<0) continue; //valid tag found //Index map @@ -795,8 +1050,17 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol) //| | | | | | | //01234567 8 90123456 7 89012345 6 78901234 5 67890123 4 56789012 3 45678901 23 //----------------------------------------------------------------------------- - //00000000 0 11110000 1 facility 1 version* 1 code*one 1 code*two 1 ???????? 11 + //00000000 0 11110000 1 facility 1 version* 1 code*one 1 code*two 1 checksum 11 // + //Checksum: + //00000000 0 11110000 1 11100000 1 00000001 1 00000011 1 10110110 1 01110101 11 + //preamble F0 E0 01 03 B6 75 + // How to calc checksum, + // http://www.proxmark.org/forum/viewtopic.php?id=364&p=6 + // F0 + E0 + 01 + 03 + B6 = 28A + // 28A & FF = 8A + // FF - 8A = 75 + // Checksum: 0x75 //XSF(version)facility:codeone+codetwo //Handle the data if(findone){ //only print binary if we are doing one @@ -811,21 +1075,30 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol) code = bytebits_to_byte(dest+idx,32); code2 = bytebits_to_byte(dest+idx+32,32); version = bytebits_to_byte(dest+idx+27,8); //14,4 - facilitycode = bytebits_to_byte(dest+idx+18,8) ; + facilitycode = bytebits_to_byte(dest+idx+18,8); number = (bytebits_to_byte(dest+idx+36,8)<<8)|(bytebits_to_byte(dest+idx+45,8)); //36,9 - Dbprintf("XSF(%02d)%02x:%05d (%08x%08x)",version,facilitycode,number,code,code2); + crc = bytebits_to_byte(dest+idx+54,8); + for (uint8_t i=1; i<6; ++i) + calccrc += bytebits_to_byte(dest+idx+9*i,8); + calccrc &= 0xff; + calccrc = 0xff - calccrc; + + char *crcStr = (crc == calccrc) ? "ok":"!crc"; + + Dbprintf("IO Prox XSF(%02d)%02x:%05d (%08x%08x) [%02x %s]",version,facilitycode,number,code,code2, crc, crcStr); // if we're only looking for one tag if (findone){ if (ledcontrol) LED_A_OFF(); - //LED_A_OFF(); + *high=code; + *low=code2; return; } code=code2=0; version=facilitycode=0; number=0; idx=0; - } + WDT_HIT(); } DbpString("Stopped"); @@ -833,395 +1106,325 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol) } /*------------------------------ - * T5555/T5557/T5567 routines + * T5555/T5557/T5567/T5577 routines *------------------------------ - */ - -/* T55x7 configuration register definitions */ -#define T55x7_POR_DELAY 0x00000001 -#define T55x7_ST_TERMINATOR 0x00000008 -#define T55x7_PWD 0x00000010 -#define T55x7_MAXBLOCK_SHIFT 5 -#define T55x7_AOR 0x00000200 -#define T55x7_PSKCF_RF_2 0 -#define T55x7_PSKCF_RF_4 0x00000400 -#define T55x7_PSKCF_RF_8 0x00000800 -#define T55x7_MODULATION_DIRECT 0 -#define T55x7_MODULATION_PSK1 0x00001000 -#define T55x7_MODULATION_PSK2 0x00002000 -#define T55x7_MODULATION_PSK3 0x00003000 -#define T55x7_MODULATION_FSK1 0x00004000 -#define T55x7_MODULATION_FSK2 0x00005000 -#define T55x7_MODULATION_FSK1a 0x00006000 -#define T55x7_MODULATION_FSK2a 0x00007000 -#define T55x7_MODULATION_MANCHESTER 0x00008000 -#define T55x7_MODULATION_BIPHASE 0x00010000 -#define T55x7_BITRATE_RF_8 0 -#define T55x7_BITRATE_RF_16 0x00040000 -#define T55x7_BITRATE_RF_32 0x00080000 -#define T55x7_BITRATE_RF_40 0x000C0000 -#define T55x7_BITRATE_RF_50 0x00100000 -#define T55x7_BITRATE_RF_64 0x00140000 -#define T55x7_BITRATE_RF_100 0x00180000 -#define T55x7_BITRATE_RF_128 0x001C0000 - -/* T5555 (Q5) configuration register definitions */ -#define T5555_ST_TERMINATOR 0x00000001 -#define T5555_MAXBLOCK_SHIFT 0x00000001 -#define T5555_MODULATION_MANCHESTER 0 -#define T5555_MODULATION_PSK1 0x00000010 -#define T5555_MODULATION_PSK2 0x00000020 -#define T5555_MODULATION_PSK3 0x00000030 -#define T5555_MODULATION_FSK1 0x00000040 -#define T5555_MODULATION_FSK2 0x00000050 -#define T5555_MODULATION_BIPHASE 0x00000060 -#define T5555_MODULATION_DIRECT 0x00000070 -#define T5555_INVERT_OUTPUT 0x00000080 -#define T5555_PSK_RF_2 0 -#define T5555_PSK_RF_4 0x00000100 -#define T5555_PSK_RF_8 0x00000200 -#define T5555_USE_PWD 0x00000400 -#define T5555_USE_AOR 0x00000800 -#define T5555_BITRATE_SHIFT 12 -#define T5555_FAST_WRITE 0x00004000 -#define T5555_PAGE_SELECT 0x00008000 - -/* - * Relevant times in microsecond + * NOTE: T55x7/T5555 configuration register definitions moved to protocols.h + * + * Relevant communication times in microsecond * To compensate antenna falling times shorten the write times * and enlarge the gap ones. + * Q5 tags seems to have issues when these values changes. */ -#define START_GAP 250 -#define WRITE_GAP 160 -#define WRITE_0 144 // 192 -#define WRITE_1 400 // 432 for T55x7; 448 for E5550 -// Write one bit to card -void T55xxWriteBit(int bit) -{ - FpgaDownloadAndGo(FPGA_BITSTREAM_LF); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz +#define START_GAP 50*8 // was 250 // SPEC: 1*8 to 50*8 - typ 15*8 (or 15fc) +#define WRITE_GAP 20*8 // was 160 // SPEC: 1*8 to 20*8 - typ 10*8 (or 10fc) +#define WRITE_0 18*8 // was 144 // SPEC: 16*8 to 32*8 - typ 24*8 (or 24fc) +#define WRITE_1 50*8 // was 400 // SPEC: 48*8 to 64*8 - typ 56*8 (or 56fc) 432 for T55x7; 448 for E5550 +#define READ_GAP 15*8 + +// VALUES TAKEN FROM EM4x function: SendForward +// START_GAP = 440; (55*8) cycles at 125Khz (8us = 1cycle) +// WRITE_GAP = 128; (16*8) +// WRITE_1 = 256 32*8; (32*8) + +// These timings work for 4469/4269/4305 (with the 55*8 above) +// WRITE_0 = 23*8 , 9*8 SpinDelayUs(23*8); + +// Sam7s has several timers, we will use the source TIMER_CLOCK1 (aka AT91C_TC_CLKS_TIMER_DIV1_CLOCK) +// TIMER_CLOCK1 = MCK/2, MCK is running at 48 MHz, Timer is running at 48/2 = 24 MHz +// Hitag units (T0) have duration of 8 microseconds (us), which is 1/125000 per second (carrier) +// T0 = TIMER_CLOCK1 / 125000 = 192 +// 1 Cycle = 8 microseconds(us) == 1 field clock + +void TurnReadLFOn(int delay) { FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); - if (bit == 0) - SpinDelayUs(WRITE_0); + + // measure antenna strength. + //int adcval = ((MAX_ADC_LF_VOLTAGE * AvgAdc(ADC_CHAN_LF)) >> 10); + + // Give it a bit of time for the resonant antenna to settle. + WaitUS(delay); +} + +// Write one bit to card +void T55xxWriteBit(int bit) { + if (!bit) + TurnReadLFOn(WRITE_0); else - SpinDelayUs(WRITE_1); + TurnReadLFOn(WRITE_1); FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - SpinDelayUs(WRITE_GAP); + WaitUS(WRITE_GAP); } -// Write one card block in page 0, no lock -void T55xxWriteBlock(uint32_t Data, uint32_t Block, uint32_t Pwd, uint8_t PwdMode) -{ - //unsigned int i; //enio adjustment 12/10/14 - uint32_t i; +// Send T5577 reset command then read stream (see if we can identify the start of the stream) +void T55xxResetRead(void) { + LED_A_ON(); + //clear buffer now so it does not interfere with timing later + BigBuf_Clear_keep_EM(); - FpgaDownloadAndGo(FPGA_BITSTREAM_LF); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); - // Give it a bit of time for the resonant antenna to settle. - // And for the tag to fully power up - SpinDelay(150); + // Trigger T55x7 in mode. + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + WaitUS(START_GAP); + + // reset tag - op code 00 + T55xxWriteBit(0); + T55xxWriteBit(0); + + // Turn field on to read the response + TurnReadLFOn(READ_GAP); + + // Acquisition + doT55x7Acquisition(BigBuf_max_traceLen()); + + // Turn the field off + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + cmd_send(CMD_ACK,0,0,0,0,0); + LED_A_OFF(); +} - // Now start writting +// Write one card block in page 0, no lock +void T55xxWriteBlockExt(uint32_t Data, uint8_t Block, uint32_t Pwd, uint8_t arg) { + LED_A_ON(); + bool PwdMode = arg & 0x1; + uint8_t Page = (arg & 0x2)>>1; + uint32_t i = 0; + + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); + + // Trigger T55x7 in mode. FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - SpinDelayUs(START_GAP); + WaitUS(START_GAP); - // Opcode + // Opcode 10 T55xxWriteBit(1); - T55xxWriteBit(0); //Page 0 - if (PwdMode == 1){ - // Pwd + T55xxWriteBit(Page); //Page 0 + if (PwdMode){ + // Send Pwd for (i = 0x80000000; i != 0; i >>= 1) T55xxWriteBit(Pwd & i); } - // Lock bit + // Send Lock bit T55xxWriteBit(0); - // Data + // Send Data for (i = 0x80000000; i != 0; i >>= 1) T55xxWriteBit(Data & i); - // Block + // Send Block number for (i = 0x04; i != 0; i >>= 1) T55xxWriteBit(Block & i); - // Now perform write (nominal is 5.6 ms for T55x7 and 18ms for E5550, + // Perform write (nominal is 5.6 ms for T55x7 and 18ms for E5550, // so wait a little more) - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); - SpinDelay(20); + TurnReadLFOn(20 * 1000); + //could attempt to do a read to confirm write took + // as the tag should repeat back the new block + // until it is reset, but to confirm it we would + // need to know the current block 0 config mode + + // turn field off FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + LED_A_OFF(); } -// Read one card block in page 0 -void T55xxReadBlock(uint32_t Block, uint32_t Pwd, uint8_t PwdMode) -{ - uint8_t *dest = (uint8_t *)BigBuf; - //int m=0, i=0; //enio adjustment 12/10/14 - uint32_t m=0, i=0; - FpgaDownloadAndGo(FPGA_BITSTREAM_LF); - m = sizeof(BigBuf); - // Clear destination buffer before sending the command - memset(dest, 128, m); - // Connect the A/D to the peak-detected low-frequency path. - SetAdcMuxFor(GPIO_MUXSEL_LOPKD); - // Now set up the SSC to get the ADC samples that are now streaming at us. - FpgaSetupSsc(); - - LED_D_ON(); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); - - // Give it a bit of time for the resonant antenna to settle. - // And for the tag to fully power up - SpinDelay(150); +// Write one card block in page 0, no lock +void T55xxWriteBlock(uint32_t Data, uint8_t Block, uint32_t Pwd, uint8_t arg) { + T55xxWriteBlockExt(Data, Block, Pwd, arg); + cmd_send(CMD_ACK,0,0,0,0,0); +} - // Now start writting +// Read one card block in page [page] +void T55xxReadBlock(uint16_t arg0, uint8_t Block, uint32_t Pwd) { + LED_A_ON(); + bool PwdMode = arg0 & 0x1; + uint8_t Page = (arg0 & 0x2) >> 1; + uint32_t i = 0; + bool RegReadMode = (Block == 0xFF); + + //clear buffer now so it does not interfere with timing later + BigBuf_Clear_keep_EM(); + + //make sure block is at max 7 + Block &= 0x7; + + // Set up FPGA, 125kHz to power up the tag + LFSetupFPGAForADC(95, true); + SpinDelay(3); + + // Trigger T55x7 Direct Access Mode with start gap FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - SpinDelayUs(START_GAP); - - // Opcode + WaitUS(START_GAP); + + // Opcode 1[page] T55xxWriteBit(1); - T55xxWriteBit(0); //Page 0 - if (PwdMode == 1){ - // Pwd + T55xxWriteBit(Page); //Page 0 + + if (PwdMode){ + // Send Pwd for (i = 0x80000000; i != 0; i >>= 1) T55xxWriteBit(Pwd & i); } - // Lock bit + // Send a zero bit separation T55xxWriteBit(0); - // Block - for (i = 0x04; i != 0; i >>= 1) - T55xxWriteBit(Block & i); + + // Send Block number (if direct access mode) + if (!RegReadMode) + for (i = 0x04; i != 0; i >>= 1) + T55xxWriteBit(Block & i); // Turn field on to read the response - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); - - // Now do the acquisition - i = 0; - for(;;) { - if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) { - AT91C_BASE_SSC->SSC_THR = 0x43; - } - if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { - dest[i] = (uint8_t)AT91C_BASE_SSC->SSC_RHR; - // we don't care about actual value, only if it's more or less than a - // threshold essentially we capture zero crossings for later analysis - // if(dest[i] < 127) dest[i] = 0; else dest[i] = 1; - i++; - if (i >= m) break; - } - } - + TurnReadLFOn(READ_GAP); + + // Acquisition + doT55x7Acquisition(12000); + + // Turn the field off FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off - LED_D_OFF(); - DbpString("DONE!"); + cmd_send(CMD_ACK,0,0,0,0,0); + LED_A_OFF(); } -// Read card traceability data (page 1) -void T55xxReadTrace(void){ - uint8_t *dest = (uint8_t *)BigBuf; - int m=0, i=0; - - FpgaDownloadAndGo(FPGA_BITSTREAM_LF); - m = sizeof(BigBuf); - // Clear destination buffer before sending the command - memset(dest, 128, m); - // Connect the A/D to the peak-detected low-frequency path. - SetAdcMuxFor(GPIO_MUXSEL_LOPKD); - // Now set up the SSC to get the ADC samples that are now streaming at us. - FpgaSetupSsc(); - - LED_D_ON(); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); - - // Give it a bit of time for the resonant antenna to settle. - // And for the tag to fully power up - SpinDelay(150); - - // Now start writting +void T55xxWakeUp(uint32_t Pwd){ + LED_B_ON(); + uint32_t i = 0; + + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); + + // Trigger T55x7 Direct Access Mode FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - SpinDelayUs(START_GAP); - - // Opcode + WaitUS(START_GAP); + + // Opcode 10 T55xxWriteBit(1); - T55xxWriteBit(1); //Page 1 - - // Turn field on to read the response - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); + T55xxWriteBit(0); //Page 0 - // Now do the acquisition - i = 0; - for(;;) { - if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) { - AT91C_BASE_SSC->SSC_THR = 0x43; - } - if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { - dest[i] = (uint8_t)AT91C_BASE_SSC->SSC_RHR; - i++; - if (i >= m) break; - } - } + // Send Pwd + for (i = 0x80000000; i != 0; i >>= 1) + T55xxWriteBit(Pwd & i); - FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off - LED_D_OFF(); - DbpString("DONE!"); + // Turn and leave field on to let the begin repeating transmission + TurnReadLFOn(20*1000); } /*-------------- Cloning routines -----------*/ +void WriteT55xx(uint32_t *blockdata, uint8_t startblock, uint8_t numblocks) { + // write last block first and config block last (if included) + for (uint8_t i = numblocks+startblock; i > startblock; i--) + T55xxWriteBlockExt(blockdata[i-1], i-1, 0, 0); +} + // Copy HID id to card and setup block 0 config -void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT) -{ - int data1=0, data2=0, data3=0, data4=0, data5=0, data6=0; //up to six blocks for long format - int last_block = 0; +void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT) { + uint32_t data[] = {0,0,0,0,0,0,0}; + uint8_t last_block = 0; if (longFMT){ // Ensure no more than 84 bits supplied - if (hi2>0xFFFFF) { + if (hi2 > 0xFFFFF) { DbpString("Tags can only have 84 bits."); return; } // Build the 6 data blocks for supplied 84bit ID last_block = 6; - data1 = 0x1D96A900; // load preamble (1D) & long format identifier (9E manchester encoded) - for (int i=0;i<4;i++) { - if (hi2 & (1<<(19-i))) - data1 |= (1<<(((3-i)*2)+1)); // 1 -> 10 - else - data1 |= (1<<((3-i)*2)); // 0 -> 01 - } - - data2 = 0; - for (int i=0;i<16;i++) { - if (hi2 & (1<<(15-i))) - data2 |= (1<<(((15-i)*2)+1)); // 1 -> 10 - else - data2 |= (1<<((15-i)*2)); // 0 -> 01 - } - - data3 = 0; - for (int i=0;i<16;i++) { - if (hi & (1<<(31-i))) - data3 |= (1<<(((15-i)*2)+1)); // 1 -> 10 - else - data3 |= (1<<((15-i)*2)); // 0 -> 01 - } - - data4 = 0; - for (int i=0;i<16;i++) { - if (hi & (1<<(15-i))) - data4 |= (1<<(((15-i)*2)+1)); // 1 -> 10 - else - data4 |= (1<<((15-i)*2)); // 0 -> 01 - } - - data5 = 0; - for (int i=0;i<16;i++) { - if (lo & (1<<(31-i))) - data5 |= (1<<(((15-i)*2)+1)); // 1 -> 10 - else - data5 |= (1<<((15-i)*2)); // 0 -> 01 - } - - data6 = 0; - for (int i=0;i<16;i++) { - if (lo & (1<<(15-i))) - data6 |= (1<<(((15-i)*2)+1)); // 1 -> 10 - else - data6 |= (1<<((15-i)*2)); // 0 -> 01 - } - } - else { + // load preamble (1D) & long format identifier (9E manchester encoded) + data[1] = 0x1D96A900 | (manchesterEncode2Bytes((hi2 >> 16) & 0xF) & 0xFF); + // load raw id from hi2, hi, lo to data blocks (manchester encoded) + data[2] = manchesterEncode2Bytes(hi2 & 0xFFFF); + data[3] = manchesterEncode2Bytes(hi >> 16); + data[4] = manchesterEncode2Bytes(hi & 0xFFFF); + data[5] = manchesterEncode2Bytes(lo >> 16); + data[6] = manchesterEncode2Bytes(lo & 0xFFFF); + } else { // Ensure no more than 44 bits supplied - if (hi>0xFFF) { + if (hi > 0xFFF) { DbpString("Tags can only have 44 bits."); return; } - // Build the 3 data blocks for supplied 44bit ID last_block = 3; - - data1 = 0x1D000000; // load preamble - - for (int i=0;i<12;i++) { - if (hi & (1<<(11-i))) - data1 |= (1<<(((11-i)*2)+1)); // 1 -> 10 - else - data1 |= (1<<((11-i)*2)); // 0 -> 01 - } - - data2 = 0; - for (int i=0;i<16;i++) { - if (lo & (1<<(31-i))) - data2 |= (1<<(((15-i)*2)+1)); // 1 -> 10 - else - data2 |= (1<<((15-i)*2)); // 0 -> 01 - } - - data3 = 0; - for (int i=0;i<16;i++) { - if (lo & (1<<(15-i))) - data3 |= (1<<(((15-i)*2)+1)); // 1 -> 10 - else - data3 |= (1<<((15-i)*2)); // 0 -> 01 - } + // load preamble + data[1] = 0x1D000000 | (manchesterEncode2Bytes(hi) & 0xFFFFFF); + data[2] = manchesterEncode2Bytes(lo >> 16); + data[3] = manchesterEncode2Bytes(lo & 0xFFFF); } + // load chip config block + data[0] = T55x7_BITRATE_RF_50 | T55x7_MODULATION_FSK2a | last_block << T55x7_MAXBLOCK_SHIFT; + + //TODO add selection of chip for Q5 or T55x7 + // data[0] = (((50-2)/2)<> 32), 1, 0, 0); - T55xxWriteBlock((uint32_t)id, 2, 0, 0); - - // Config for EM410x (RF/64, Manchester, Maxblock=2) - if (card) { - // Clock rate is stored in bits 8-15 of the card value - clock = (card & 0xFF00) >> 8; - Dbprintf("Clock rate: %d", clock); - switch (clock) - { - case 32: - clock = T55x7_BITRATE_RF_32; - break; - case 16: - clock = T55x7_BITRATE_RF_16; - break; - case 0: - // A value of 0 is assumed to be 64 for backwards-compatibility - // Fall through... - case 64: - clock = T55x7_BITRATE_RF_64; - break; - default: - Dbprintf("Invalid clock rate: %d", clock); - return; - } - - // Writing configuration for T55x7 tag - T55xxWriteBlock(clock | - T55x7_MODULATION_MANCHESTER | - 2 << T55x7_MAXBLOCK_SHIFT, - 0, 0, 0); - } - else - // Writing configuration for T5555(Q5) tag - T55xxWriteBlock(0x1F << T5555_BITRATE_SHIFT | - T5555_MODULATION_MANCHESTER | - 2 << T5555_MAXBLOCK_SHIFT, - 0, 0, 0); - - LED_D_OFF(); - Dbprintf("Tag %s written with 0x%08x%08x\n", card ? "T55x7":"T5555", - (uint32_t)(id >> 32), (uint32_t)id); -} - -// Clone Indala 64-bit tag by UID to T55x7 -void CopyIndala64toT55x7(int hi, int lo) -{ - - //Program the 2 data blocks for supplied 64bit UID - // and the block 0 for Indala64 format - T55xxWriteBlock(hi,1,0,0); - T55xxWriteBlock(lo,2,0,0); - //Config for Indala (RF/32;PSK1 with RF/2;Maxblock=2) - T55xxWriteBlock(T55x7_BITRATE_RF_32 | - T55x7_MODULATION_PSK1 | - 2 << T55x7_MAXBLOCK_SHIFT, - 0, 0, 0); - //Alternative config for Indala (Extended mode;RF/32;PSK1 with RF/2;Maxblock=2;Inverse data) - // T5567WriteBlock(0x603E1042,0); - - DbpString("DONE!"); - -} - -void CopyIndala224toT55x7(int uid1, int uid2, int uid3, int uid4, int uid5, int uid6, int uid7) -{ - - //Program the 7 data blocks for supplied 224bit UID - // and the block 0 for Indala224 format - T55xxWriteBlock(uid1,1,0,0); - T55xxWriteBlock(uid2,2,0,0); - T55xxWriteBlock(uid3,3,0,0); - T55xxWriteBlock(uid4,4,0,0); - T55xxWriteBlock(uid5,5,0,0); - T55xxWriteBlock(uid6,6,0,0); - T55xxWriteBlock(uid7,7,0,0); - //Config for Indala (RF/32;PSK1 with RF/2;Maxblock=7) - T55xxWriteBlock(T55x7_BITRATE_RF_32 | - T55x7_MODULATION_PSK1 | - 7 << T55x7_MAXBLOCK_SHIFT, - 0,0,0); - //Alternative config for Indala (Extended mode;RF/32;PSK1 with RF/2;Maxblock=7;Inverse data) - // T5567WriteBlock(0x603E10E2,0); - - DbpString("DONE!"); - -} - - -#define abs(x) ( ((x)<0) ? -(x) : (x) ) -#define max(x,y) ( x GraphBuffer[0]) { - while(i < GraphTraceLen) { - if( !(GraphBuffer[i] > GraphBuffer[i-1]) && GraphBuffer[i] > lmax) - break; - i++; - } - dir = 0; - } - else { - while(i < GraphTraceLen) { - if( !(GraphBuffer[i] < GraphBuffer[i-1]) && GraphBuffer[i] < lmin) - break; - i++; - } - dir = 1; - } - - lastval = i++; - half_switch = 0; - pmc = 0; - block_done = 0; - - for (bitidx = 0; i < GraphTraceLen; i++) - { - if ( (GraphBuffer[i-1] > GraphBuffer[i] && dir == 1 && GraphBuffer[i] > lmax) || (GraphBuffer[i-1] < GraphBuffer[i] && dir == 0 && GraphBuffer[i] < lmin)) - { - lc = i - lastval; - lastval = i; - - // Switch depending on lc length: - // Tolerance is 1/8 of clock rate (arbitrary) - if (abs(lc-clock/4) < tolerance) { - // 16T0 - if((i - pmc) == lc) { /* 16T0 was previous one */ - /* It's a PMC ! */ - i += (128+127+16+32+33+16)-1; - lastval = i; - pmc = 0; - block_done = 1; - } - else { - pmc = i; - } - } else if (abs(lc-clock/2) < tolerance) { - // 32TO - if((i - pmc) == lc) { /* 16T0 was previous one */ - /* It's a PMC ! */ - i += (128+127+16+32+33)-1; - lastval = i; - pmc = 0; - block_done = 1; - } - else if(half_switch == 1) { - BitStream[bitidx++] = 0; - half_switch = 0; - } - else - half_switch++; - } else if (abs(lc-clock) < tolerance) { - // 64TO - BitStream[bitidx++] = 1; - } else { - // Error - warnings++; - if (warnings > 10) - { - Dbprintf("Error: too many detection errors, aborting."); - return 0; - } - } - - if(block_done == 1) { - if(bitidx == 128) { - for(j=0; j<16; j++) { - Blocks[num_blocks][j] = 128*BitStream[j*8+7]+ - 64*BitStream[j*8+6]+ - 32*BitStream[j*8+5]+ - 16*BitStream[j*8+4]+ - 8*BitStream[j*8+3]+ - 4*BitStream[j*8+2]+ - 2*BitStream[j*8+1]+ - BitStream[j*8]; - } - num_blocks++; - } - bitidx = 0; - block_done = 0; - half_switch = 0; - } - if(i < GraphTraceLen) - { - if (GraphBuffer[i-1] > GraphBuffer[i]) dir=0; - else dir = 1; - } - } - if(bitidx==255) - bitidx=0; - warnings = 0; - if(num_blocks == 4) break; - } - memcpy(outBlocks, Blocks, 16*num_blocks); - return num_blocks; -} - -int IsBlock0PCF7931(uint8_t *Block) { - // Assume RFU means 0 :) - if((memcmp(Block, "\x00\x00\x00\x00\x00\x00\x00\x01", 8) == 0) && memcmp(Block+9, "\x00\x00\x00\x00\x00\x00\x00", 7) == 0) // PAC enabled - return 1; - if((memcmp(Block+9, "\x00\x00\x00\x00\x00\x00\x00", 7) == 0) && Block[7] == 0) // PAC disabled, can it *really* happen ? - return 1; - return 0; -} - -int IsBlock1PCF7931(uint8_t *Block) { - // Assume RFU means 0 :) - if(Block[10] == 0 && Block[11] == 0 && Block[12] == 0 && Block[13] == 0) - if((Block[14] & 0x7f) <= 9 && Block[15] <= 9) - return 1; - - return 0; -} - -#define ALLOC 16 - -void ReadPCF7931() { - uint8_t Blocks[8][17]; - uint8_t tmpBlocks[4][16]; - int i, j, ind, ind2, n; - int num_blocks = 0; - int max_blocks = 8; - int ident = 0; - int error = 0; - int tries = 0; - - memset(Blocks, 0, 8*17*sizeof(uint8_t)); - - do { - memset(tmpBlocks, 0, 4*16*sizeof(uint8_t)); - n = DemodPCF7931((uint8_t**)tmpBlocks); - if(!n) - error++; - if(error==10 && num_blocks == 0) { - Dbprintf("Error, no tag or bad tag"); + uint32_t data[] = {0, (uint32_t)(id>>32), (uint32_t)(id & 0xFFFFFFFF)}; + + clock = (card & 0xFF00) >> 8; + clock = (clock == 0) ? 64 : clock; + Dbprintf("Clock rate: %d", clock); + if (card & 0xFF) { //t55x7 + clock = GetT55xxClockBit(clock); + if (clock == 0) { + Dbprintf("Invalid clock rate: %d", clock); return; } - else if (tries==20 || error==10) { - Dbprintf("Error reading the tag"); - Dbprintf("Here is the partial content"); - goto end; - } - - for(i=0; i= 0; ind--,ind2--) { - if(ind2 < 0) - ind2 = max_blocks; - if(!Blocks[ind2][ALLOC]) { // Block ind2 not already found - // Dbprintf("Tmp %d -> Block %d", ind, ind2); - memcpy(Blocks[ind2], tmpBlocks[ind], 16); - Blocks[ind2][ALLOC] = 1; - num_blocks++; - if(num_blocks == max_blocks) goto end; - } - } - for(ind=i+1,ind2=j+1; ind < n; ind++,ind2++) { - if(ind2 > max_blocks) - ind2 = 0; - if(!Blocks[ind2][ALLOC]) { // Block ind2 not already found - // Dbprintf("Tmp %d -> Block %d", ind, ind2); - memcpy(Blocks[ind2], tmpBlocks[ind], 16); - Blocks[ind2][ALLOC] = 1; - num_blocks++; - if(num_blocks == max_blocks) goto end; - } - } - } - } - } - } - } - tries++; - if (BUTTON_PRESS()) return; - } while (num_blocks != max_blocks); -end: - Dbprintf("-----------------------------------------"); - Dbprintf("Memory content:"); - Dbprintf("-----------------------------------------"); - for(i=0; i", i); + data[0] = clock | T55x7_MODULATION_MANCHESTER | (2 << T55x7_MAXBLOCK_SHIFT); + } else { //t5555 (Q5) + clock = (clock-2)>>1; //n = (RF-2)/2 + data[0] = (clock << T5555_BITRATE_SHIFT) | T5555_MODULATION_MANCHESTER | (2 << T5555_MAXBLOCK_SHIFT); } - Dbprintf("-----------------------------------------"); + + WriteT55xx(data, 0, 3); - return ; + LED_D_OFF(); + Dbprintf("Tag %s written with 0x%08x%08x\n", + card ? "T55x7":"T5555", + (uint32_t)(id >> 32), + (uint32_t)id); } - //----------------------------------- // EM4469 / EM4305 routines //----------------------------------- @@ -1641,7 +1518,6 @@ end: #define FWD_CMD_READ 0x9 #define FWD_CMD_DISABLE 0x5 - uint8_t forwardLink_data[64]; //array of forwarded bits uint8_t * forward_ptr; //ptr for forward message preparation uint8_t fwd_bit_sz; //forwardlink bit counter @@ -1652,8 +1528,15 @@ uint8_t * fwd_write_ptr; //forwardlink bit pointer // see EM4469 spec //==================================================================== //-------------------------------------------------------------------- +// VALUES TAKEN FROM EM4x function: SendForward +// START_GAP = 440; (55*8) cycles at 125Khz (8us = 1cycle) +// WRITE_GAP = 128; (16*8) +// WRITE_1 = 256 32*8; (32*8) + +// These timings work for 4469/4269/4305 (with the 55*8 above) +// WRITE_0 = 23*8 , 9*8 SpinDelayUs(23*8); + uint8_t Prepare_Cmd( uint8_t cmd ) { - //-------------------------------------------------------------------- *forward_ptr++ = 0; //start bit *forward_ptr++ = 0; //second pause for 4050 code @@ -1673,10 +1556,7 @@ uint8_t Prepare_Cmd( uint8_t cmd ) { // prepares address bits // see EM4469 spec //==================================================================== - -//-------------------------------------------------------------------- uint8_t Prepare_Addr( uint8_t addr ) { - //-------------------------------------------------------------------- register uint8_t line_parity; @@ -1697,10 +1577,7 @@ uint8_t Prepare_Addr( uint8_t addr ) { // prepares data bits intreleaved with parity bits // see EM4469 spec //==================================================================== - -//-------------------------------------------------------------------- uint8_t Prepare_Data( uint16_t data_low, uint16_t data_hi) { - //-------------------------------------------------------------------- register uint8_t line_parity; register uint8_t column_parity; @@ -1744,35 +1621,27 @@ void SendForward(uint8_t fwd_bit_count) { LED_D_ON(); - //Field on - FpgaDownloadAndGo(FPGA_BITSTREAM_LF); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); - - // Give it a bit of time for the resonant antenna to settle. - // And for the tag to fully power up - SpinDelay(150); - + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); + // force 1st mod pulse (start gap must be longer for 4305) fwd_bit_sz--; //prepare next bit modulation fwd_write_ptr++; FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off - SpinDelayUs(55*8); //55 cycles off (8us each)for 4305 - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz + WaitUS(55*8); //55 cycles off (8us each)for 4305 // ICEMAN: problem with (us) clock is 21.3us increments FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);//field on - SpinDelayUs(16*8); //16 cycles on (8us each) + WaitUS(16*8); //16 cycles on (8us each) // ICEMAN: problem with (us) clock is 21.3us increments // now start writting while(fwd_bit_sz-- > 0) { //prepare next bit modulation if(((*fwd_write_ptr++) & 1) == 1) - SpinDelayUs(32*8); //32 cycles at 125Khz (8us each) + WaitUS(32*8); //32 cycles at 125Khz (8us each) // ICEMAN: problem with (us) clock is 21.3us increments else { //These timings work for 4469/4269/4305 (with the 55*8 above) FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off - SpinDelayUs(23*8); //16-4 cycles off (8us each) - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz + WaitUS(23*8); //16-4 cycles off (8us each) // ICEMAN: problem with (us) clock is 21.3us increments FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);//field on - SpinDelayUs(9*8); //16 cycles on (8us each) + WaitUS(9*8); //16 cycles on (8us each) // ICEMAN: problem with (us) clock is 21.3us increments } } } @@ -1789,15 +1658,18 @@ void EM4xLogin(uint32_t Password) { //Wait for command to complete SpinDelay(20); - } void EM4xReadWord(uint8_t Address, uint32_t Pwd, uint8_t PwdMode) { uint8_t fwd_bit_count; - uint8_t *dest = (uint8_t *)BigBuf; - int m=0, i=0; + uint8_t *dest = BigBuf_get_addr(); + uint16_t bufsize = BigBuf_max_traceLen(); + uint32_t i = 0; + // Clear destination buffer before sending the command + BigBuf_Clear_ext(false); + //If password mode do login if (PwdMode == 1) EM4xLogin(Pwd); @@ -1805,9 +1677,6 @@ void EM4xReadWord(uint8_t Address, uint32_t Pwd, uint8_t PwdMode) { fwd_bit_count = Prepare_Cmd( FWD_CMD_READ ); fwd_bit_count += Prepare_Addr( Address ); - m = sizeof(BigBuf); - // Clear destination buffer before sending the command - memset(dest, 128, m); // Connect the A/D to the peak-detected low-frequency path. SetAdcMuxFor(GPIO_MUXSEL_LOPKD); // Now set up the SSC to get the ADC samples that are now streaming at us. @@ -1823,11 +1692,13 @@ void EM4xReadWord(uint8_t Address, uint32_t Pwd, uint8_t PwdMode) { } if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { dest[i] = (uint8_t)AT91C_BASE_SSC->SSC_RHR; - i++; - if (i >= m) break; + ++i; + if (i >= bufsize) break; } } - FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + cmd_send(CMD_ACK,0,0,0,0,0); LED_D_OFF(); }