X-Git-Url: http://cvs.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/30f2a7d38fd35b2427a7eb42e1cd75fb1105f927..022c8791c14841d9c32f19b8b06ef6651bdcbd15:/fpga/lo_read.v

diff --git a/fpga/lo_read.v b/fpga/lo_read.v
index d7b45cb5..8dce4dda 100644
--- a/fpga/lo_read.v
+++ b/fpga/lo_read.v
@@ -1,8 +1,7 @@
 //-----------------------------------------------------------------------------
 // The way that we connect things in low-frequency read mode. In this case
-// we are generating the 134 kHz or 125 kHz carrier, and running the
-// unmodulated carrier at that frequency. The A/D samples at that same rate,
-// and the result is serialized.
+// we are generating the unmodulated low frequency carrier.
+// The A/D samples at that same rate and the result is serialized.
 //
 // Jonathan Westhues, April 2006
 //-----------------------------------------------------------------------------
@@ -24,54 +23,81 @@ module lo_read(
     output ssp_frame, ssp_din, ssp_clk;
     input cross_hi, cross_lo;
     output dbg;
-    input lo_is_125khz;
+    input lo_is_125khz; // redundant signal, no longer used anywhere
     input [7:0] divisor;
 
-// The low-frequency RFID stuff. This is relatively simple, because most
-// of the work happens on the ARM, and we just pass samples through. The
-// PCK0 must be divided down to generate the A/D clock, and from there by
-// a factor of 8 to generate the carrier (that we apply to the coil drivers).
-//
-// This is also where we decode the received synchronous serial port words,
-// to determine how to drive the output enables.
-
-// PCK0 will run at (PLL clock) / 4, or 24 MHz. That means that we can do
-// 125 kHz by dividing by a further factor of (8*12*2), or ~134 kHz by
-// dividing by a factor of (8*11*2) (for 136 kHz, ~2% error, tolerable).
-
 reg [7:0] to_arm_shiftreg;
 reg [7:0] pck_divider;
-reg [6:0] ssp_divider;
 reg ant_lo;
 
+// this task runs on the rising egde of pck0 clock (24Mhz) and creates ant_lo
+// which is high for (divisor+1) pck0 cycles and low for the same duration
+// ant_lo is therefore a 50% duty cycle clock signal with a frequency of
+// 12Mhz/(divisor+1) which drives the antenna as well as the ADC clock adc_clk
 always @(posedge pck0)
 begin
-	if(pck_divider == 8'd0)
+	if(pck_divider == divisor[7:0])
 		begin
-			pck_divider <= divisor[7:0];
+			pck_divider <= 8'd0;
 			ant_lo = !ant_lo;
-			if(ant_lo == 1'b0)
-			begin
-			    ssp_divider <= 7'b0011111;
-				to_arm_shiftreg <= adc_d;
-			end
 		end
 	else
 	begin
-		pck_divider <= pck_divider - 1;
-		if(ssp_divider[6] == 1'b0)
-		begin
-			if (ssp_divider[1:0] == 1'b11) to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
-			ssp_divider <= ssp_divider - 1;
-		end
+		pck_divider <= pck_divider + 1;
+	end
+end
+
+// this task also runs at pck0 frequency (24Mhz) and is used to serialize
+// the ADC output which is then clocked into the ARM SSP.
+
+// because ant_lo always transitions when pck_divider = 0 we use the
+// pck_divider counter to sync our other signals off it
+// we read the ADC value when pck_divider=7 and shift it out on counts 8..15
+always @(posedge pck0)
+begin
+	if((pck_divider == 8'd7) && !ant_lo)
+        to_arm_shiftreg <= adc_d;
+    else
+	begin
+        to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
+		// simulation showed a glitch occuring due to the LSB of the shifter
+		// not being set as we shift bits out
+		// this ensures the ssp_din remains low after a transfer and suppresses
+		// the glitch that would occur when the last data shifted out ended in
+		// a 1 bit and the next data shifted out started with a 0 bit
+        to_arm_shiftreg[0] <= 1'b0;
 	end
 end
 
-assign ssp_din = to_arm_shiftreg[7];
-assign ssp_clk = pck_divider[1];
-assign ssp_frame = ~ssp_divider[5];
+// ADC samples on falling edge of adc_clk, data available on the rising edge
+
+// example of ssp transfer of binary value 1100101
+// start of transfer is indicated by the rise of the ssp_frame signal
+// ssp_din changes on the rising edge of the ssp_clk clock and is clocked into
+// the ARM by the falling edge of ssp_clk
+//             _______________________________
+// ssp_frame__|                               |__
+//             _______         ___     ___
+// ssp_din  __|       |_______|   |___|   |______
+//         _   _   _   _   _   _   _   _   _   _
+// ssp_clk  |_| |_| |_| |_| |_| |_| |_| |_| |_| |_
+
+// serialized SSP data is gated by ant_lo to suppress unwanted signal
+assign ssp_din = to_arm_shiftreg[7] && !ant_lo;
+// SSP clock always runs at 24Mhz
+assign ssp_clk = pck0;
+// SSP frame is gated by ant_lo and goes high when pck_divider=8..15
+assign ssp_frame = (pck_divider[7:3] == 5'd1) && !ant_lo;
+// unused signals tied low
 assign pwr_hi = 1'b0;
+assign pwr_oe1 = 1'b0;
+assign pwr_oe2 = 1'b0;
+assign pwr_oe3 = 1'b0;
+assign pwr_oe4 = 1'b0;
+// this is the antenna driver signal
 assign pwr_lo = ant_lo;
+// ADC clock out of phase with antenna driver
 assign adc_clk = ~ant_lo;
+// ADC clock also routed to debug pin
 assign dbg = adc_clk;
 endmodule