X-Git-Url: http://cvs.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/5e0b213d7fff242eed777eabef722349d069b342..735136e6a33e4851127b45d373ea58f1710bd1f4:/README.txt?ds=sidebyside diff --git a/README.txt b/README.txt index 1e46bf0c..1a4ddb6d 100644 --- a/README.txt +++ b/README.txt @@ -1,94 +1,52 @@ NOTICE: -(2014-03-17) -Moving the repository from google code to GitHub is up for discussion! -Please check out the following thread and post your comments... -http://www.proxmark.org/forum/viewtopic.php?id=1902 -Discussions will close on March 31st. +(2014-03-26) +This is now the official Proxmark repository! -INTRO: +INTRODUCTION: -This file contains enough software, logic (for the FPGA), and design -documentation for the hardware that you could, at least in theory, -do something useful with a proxmark3. It has commands to: - - * read any kind of 125 kHz unidirectional tag - * simulate any kind of 125 kHz unidirectional tag - -(This is enough to perform all of the silly cloning attacks, like the -ones that I did at the Capitol in Sacramento, or anything involving -a Verichip. From a technical standpoint, these are not that exciting, -although the `software radio' architecture of the proxmark3 makes it -easy and fun to support new formats.) - -As a bonus, I include some code to use the 13.56 MHz hardware, so you can: - - * do anything that a (medium-range) ISO 15693 reader could - * read an ISO 14443 tag, if you know the higher-layer protocol - * pretend to be an ISO 14443 tag, if you know the higher-layer protocol - * snoop on an ISO 14443 transaction - -I am not actively developing any of this. I have other projects that -seem to be more useful. - -USING THE PACKAGE: - -The software tools required to build include: - - * cygwin or other unix-like tools for Windows - * devkitPro (http://wiki.devkitpro.org/index.php/Getting_Started/devkitARM) - * Xilinx's WebPack tools - * Modelsim (for test only) - * perl - -When installing devkitPro, you only need to install the compiler itself. Additional -support libraries are not required. - -Documentation is minimal, but see the doc/ directory for what exists. A -previous familiarity with the ARM, with digital signal processing, -and with embedded programming in general is assumed. - -The device is used through a specialized command line interface; for -example, to clone a Verichip, you might type: - - loread ; this reads the tag, and stores the - ; raw samples in memory on the ARM - - losamples ; then we download the samples to - ; the PC - - vchdemod clone ; demodulate the ID, and then put it - ; back in a format that we can replay - - losim ; and then replay it - -To read an ISO 15693 tag, you might type: +The proxmark3 is a powerful general purpose RFID tool, the size of a deck +of cards, designed to snoop, listen and emulate everything from +Low Frequency (125kHz) to High Frequency (13.56MHz) tags. - hiread ; read the tag; this involves sending a - ; particular command, and then getting - ; the response (which is stored as raw - ; samples in memory on the ARM) - - hisamples ; then download those samples to the PC - - hi15demod ; and demod them to bits (and check the - ; CRC etc. at the same time) - -Notice that in both cases the signal processing mostly happened on the PC -side; that is of course not practical for a real reader, but it is easier -to initially write your code and debug on the PC side than on the ARM. As -long as you use integer math (and I do), it's trivial to port it over -when you're done. - -The USB driver and bootloader are documented (and available separately -for download, if you wish to use them in another project) at +This repository contains enough software, logic (for the FPGA), and design +documentation for the hardware that you could, at least in theory, +do something useful with a proxmark3. + +RESOURCES: + + * This repository! + https://github.com/Proxmark/proxmark3 + + * The Wiki + https://github.com/Proxmark/proxmark3/wiki + + * The GitHub page + http://proxmark.github.io/proxmark3/ + + * The Forum + http://www.proxmark.org/forum + + * The IRC chanel + irc.freenode.org #proxmark3 + -or- + http://webchat.freenode.net/?channels=#proxmark3 + +DEVELOPMENT: + +The tools required to build or run the project will vary depending on +your operating system. Please refer to the Wiki for details. + + * https://github.com/Proxmark/proxmark3/wiki - http://cq.cx/trivia.pl +OBTAINING HARDWARE: +The Proxmark 3 is available for purchase (assembled and tested) from the +following locations: -OBTAINING HARDWARE: + * http://proxmark3.com/ + * http://www.xfpga.com/ -Most of the ultra-low-volume contract assemblers that have sprung up -(Screaming Circuits, the various cheap Asian suppliers, etc.) could put +Most of the ultra-low-volume contract assemblers could put something like this together with a reasonable yield. A run of around a dozen units is probably cost-effective. The BOM includes (possibly- outdated) component pricing, and everything is available from Digikey @@ -106,37 +64,6 @@ The printed circuit board artwork is also available, as Gerbers and an Excellon drill file. -FUTURE PLANS, ENHANCEMENTS THAT YOU COULD MAKE: - -At some point I should write software involving a proper real-time -operating system for the ARM. I would then provide interrupt-driven -drivers for many of the peripherals that are polled now (the USB, -the data stream from the FPGA), which would make it easier to develop -complex applications. - -It would not be all that hard to implement the ISO 15693 reader properly -(with anticollision, all the commands supported, and so on)--the signal -processing is already written, so it is all straightforward applications -work. - -I have basic support for ISO 14443 as well: a sniffer, a simulated -tag, and a reader. It won't do anything useful unless you fill in the -high-layer protocol. - -Nicer (i.e., closer-to-optimal) implementations of all kinds of signal -processing would be useful as well. - -A practical implementation of the learning-the-tag's-ID-from-what-the- -reader-broadcasts-during-anticollision attacks would be relatively -straightforward. This would involve some signal processing on the FPGA, -but not much else after that. - -It would be neat to write a driver that could stream samples from the A/Ds -over USB to the PC, using the full available bandwidth of USB. I am not -yet sure what that would be good for, but surely something. This would -require a kernel-mode driver under Windows, though, which is more work. - - LICENSING: This program is free software; you can redistribute it and/or modify @@ -158,4 +85,3 @@ Jonathan Westhues user jwesthues, at host cq.cx May 2007, Cambridge MA -