X-Git-Url: http://cvs.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/8e7a6ce40927baad799e6433422d87edef8d489d..8691f5b7bbe9138e9a4aa421da9a374536a8b556:/fpga/fpga.v

diff --git a/fpga/fpga.v b/fpga/fpga.v
index 8f8f3825..4002945b 100644
--- a/fpga/fpga.v
+++ b/fpga/fpga.v
@@ -1,209 +1,213 @@
-//-----------------------------------------------------------------------------
-// The FPGA is responsible for interfacing between the A/D, the coil drivers,
-// and the ARM. In the low-frequency modes it passes the data straight
-// through, so that the ARM gets raw A/D samples over the SSP. In the high-
-// frequency modes, the FPGA might perform some demodulation first, to
-// reduce the amount of data that we must send to the ARM.
-//
-// I am not really an FPGA/ASIC designer, so I am sure that a lot of this
-// could be improved.
-//
-// Jonathan Westhues, March 2006
-// Added ISO14443-A support by Gerhard de Koning Gans, April 2008
-//-----------------------------------------------------------------------------
-
-`include "lo_read.v"
-`include "lo_passthru.v"
-`include "lo_simulate.v"
-`include "hi_read_tx.v"
-`include "hi_read_rx_xcorr.v"
-`include "hi_simulate.v"
-`include "hi_iso14443a.v"
-`include "util.v"
-
-module fpga(
-	spcki, miso, mosi, ncs,
-	pck0i, ck_1356meg, ck_1356megb,
-	pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
-	adc_d, adc_clk, adc_noe,
-	ssp_frame, ssp_din, ssp_dout, ssp_clk,
-	cross_hi, cross_lo,
-	dbg
-);
-	input spcki, mosi, ncs;
-	output miso;
-	input pck0i, ck_1356meg, ck_1356megb;
-	output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
-	input [7:0] adc_d;
-	output adc_clk, adc_noe;
-	input ssp_dout;
-	output ssp_frame, ssp_din, ssp_clk;
-	input cross_hi, cross_lo;
-	output dbg;
-
-//assign pck0 = pck0i;
-	IBUFG #(.IOSTANDARD("DEFAULT") ) pck0b(
-		.O(pck0),
-		.I(pck0i)
-	);
-//assign spck = spcki;
-	IBUFG #(.IOSTANDARD("DEFAULT") ) spckb(
-		.O(spck),
-		.I(spcki)
-	);
-//-----------------------------------------------------------------------------
-// The SPI receiver. This sets up the configuration word, which the rest of
-// the logic looks at to determine how to connect the A/D and the coil
-// drivers (i.e., which section gets it). Also assign some symbolic names
-// to the configuration bits, for use below.
-//-----------------------------------------------------------------------------
-
-reg [15:0] shift_reg;
-reg [7:0] divisor;
-reg [7:0] conf_word;
-
-// We switch modes between transmitting to the 13.56 MHz tag and receiving
-// from it, which means that we must make sure that we can do so without
-// glitching, or else we will glitch the transmitted carrier.
-always @(posedge ncs)
-begin
-	case(shift_reg[15:12])
-		4'b0001: conf_word <= shift_reg[7:0];
-		4'b0010: divisor <= shift_reg[7:0];
-	endcase
-end
-
-always @(posedge spck)
-begin
-	if(~ncs)
-	begin
-		shift_reg[15:1] <= shift_reg[14:0];
-		shift_reg[0] <= mosi;
-	end
-end
-
-wire [2:0] major_mode;
-assign major_mode = conf_word[7:5];
-
-// For the low-frequency configuration:
-wire lo_is_125khz;
-assign lo_is_125khz = conf_word[3];
-
-// For the high-frequency transmit configuration: modulation depth, either
-// 100% (just quite driving antenna, steady LOW), or shallower (tri-state
-// some fraction of the buffers)
-wire hi_read_tx_shallow_modulation;
-assign hi_read_tx_shallow_modulation = conf_word[0];
-
-// For the high-frequency receive correlator: frequency against which to
-// correlate.
-wire hi_read_rx_xcorr_848;
-assign hi_read_rx_xcorr_848 = conf_word[0];
-// and whether to drive the coil (reader) or just short it (snooper)
-wire hi_read_rx_xcorr_snoop;
-assign hi_read_rx_xcorr_snoop = conf_word[1];
-
-// For the high-frequency simulated tag: what kind of modulation to use.
-wire [2:0] hi_simulate_mod_type;
-assign hi_simulate_mod_type = conf_word[2:0];
-
-//-----------------------------------------------------------------------------
-// And then we instantiate the modules corresponding to each of the FPGA's
-// major modes, and use muxes to connect the outputs of the active mode to
-// the output pins.
-//-----------------------------------------------------------------------------
-
-lo_read lr(
-	pck0, ck_1356meg, ck_1356megb,
-	lr_pwr_lo, lr_pwr_hi, lr_pwr_oe1, lr_pwr_oe2, lr_pwr_oe3, lr_pwr_oe4,
-	adc_d, lr_adc_clk,
-	lr_ssp_frame, lr_ssp_din, ssp_dout, lr_ssp_clk,
-	cross_hi, cross_lo,
-	lr_dbg,
-	lo_is_125khz, divisor
-);
-
-lo_passthru lp(
-	pck0, ck_1356meg, ck_1356megb,
-	lp_pwr_lo, lp_pwr_hi, lp_pwr_oe1, lp_pwr_oe2, lp_pwr_oe3, lp_pwr_oe4,
-	adc_d, lp_adc_clk,
-	lp_ssp_frame, lp_ssp_din, ssp_dout, lp_ssp_clk,
-	cross_hi, cross_lo,
-	lp_dbg, divisor
-);
-
-lo_simulate ls(
-	pck0, ck_1356meg, ck_1356megb,
-	ls_pwr_lo, ls_pwr_hi, ls_pwr_oe1, ls_pwr_oe2, ls_pwr_oe3, ls_pwr_oe4,
-	adc_d, ls_adc_clk,
-	ls_ssp_frame, ls_ssp_din, ssp_dout, ls_ssp_clk,
-	cross_hi, cross_lo,
-	ls_dbg
-);
-
-hi_read_tx ht(
-	pck0, ck_1356meg, ck_1356megb,
-	ht_pwr_lo, ht_pwr_hi, ht_pwr_oe1, ht_pwr_oe2, ht_pwr_oe3, ht_pwr_oe4,
-	adc_d, ht_adc_clk,
-	ht_ssp_frame, ht_ssp_din, ssp_dout, ht_ssp_clk,
-	cross_hi, cross_lo,
-	ht_dbg,
-	hi_read_tx_shallow_modulation
-);
-
-hi_read_rx_xcorr hrxc(
-	pck0, ck_1356meg, ck_1356megb,
-	hrxc_pwr_lo, hrxc_pwr_hi, hrxc_pwr_oe1, hrxc_pwr_oe2, hrxc_pwr_oe3,	hrxc_pwr_oe4,
-	adc_d, hrxc_adc_clk,
-	hrxc_ssp_frame, hrxc_ssp_din, ssp_dout, hrxc_ssp_clk,
-	cross_hi, cross_lo,
-	hrxc_dbg,
-	hi_read_rx_xcorr_848, hi_read_rx_xcorr_snoop
-);
-
-hi_simulate hs(
-	pck0, ck_1356meg, ck_1356megb,
-	hs_pwr_lo, hs_pwr_hi, hs_pwr_oe1, hs_pwr_oe2, hs_pwr_oe3, hs_pwr_oe4,
-	adc_d, hs_adc_clk,
-	hs_ssp_frame, hs_ssp_din, ssp_dout, hs_ssp_clk,
-	cross_hi, cross_lo,
-	hs_dbg,
-	hi_simulate_mod_type
-);
-
-hi_iso14443a hisn(
-	pck0, ck_1356meg, ck_1356megb,
-	hisn_pwr_lo, hisn_pwr_hi, hisn_pwr_oe1, hisn_pwr_oe2, hisn_pwr_oe3,	hisn_pwr_oe4,
-	adc_d, hisn_adc_clk,
-	hisn_ssp_frame, hisn_ssp_din, ssp_dout, hisn_ssp_clk,
-	cross_hi, cross_lo,
-	hisn_dbg,
-	hi_simulate_mod_type
-);
-
-// Major modes:
-//   000 --  LF reader (generic)
-//   001 --  LF simulated tag (generic)
-//   010 --  HF reader, transmitting to tag; modulation depth selectable
-//   011 --  HF reader, receiving from tag, correlating as it goes; frequency selectable
-//   100 --  HF simulated tag
-//   101 --  HF ISO14443-A
-//   110 --  LF passthrough
-//   111 --  everything off
-
-mux8 mux_ssp_clk		(major_mode, ssp_clk,   lr_ssp_clk,   ls_ssp_clk,   ht_ssp_clk,   hrxc_ssp_clk,   hs_ssp_clk,   hisn_ssp_clk,   lp_ssp_clk,   1'b0);
-mux8 mux_ssp_din		(major_mode, ssp_din,   lr_ssp_din,   ls_ssp_din,   ht_ssp_din,   hrxc_ssp_din,   hs_ssp_din,   hisn_ssp_din,   lp_ssp_din,   1'b0);
-mux8 mux_ssp_frame	(major_mode, ssp_frame, lr_ssp_frame, ls_ssp_frame, ht_ssp_frame, hrxc_ssp_frame, hs_ssp_frame, hisn_ssp_frame, lp_ssp_frame, 1'b0);
-mux8 mux_pwr_oe1		(major_mode, pwr_oe1,   lr_pwr_oe1,   ls_pwr_oe1,   ht_pwr_oe1,   hrxc_pwr_oe1,   hs_pwr_oe1,   hisn_pwr_oe1,   lp_pwr_oe1,   1'b0);
-mux8 mux_pwr_oe2		(major_mode, pwr_oe2,   lr_pwr_oe2,   ls_pwr_oe2,   ht_pwr_oe2,   hrxc_pwr_oe2,   hs_pwr_oe2,   hisn_pwr_oe2,   lp_pwr_oe2,   1'b0);
-mux8 mux_pwr_oe3		(major_mode, pwr_oe3,   lr_pwr_oe3,   ls_pwr_oe3,   ht_pwr_oe3,   hrxc_pwr_oe3,   hs_pwr_oe3,   hisn_pwr_oe3,   lp_pwr_oe3,   1'b0);
-mux8 mux_pwr_oe4		(major_mode, pwr_oe4,   lr_pwr_oe4,   ls_pwr_oe4,   ht_pwr_oe4,   hrxc_pwr_oe4,   hs_pwr_oe4,   hisn_pwr_oe4,   lp_pwr_oe4,   1'b0);
-mux8 mux_pwr_lo			(major_mode, pwr_lo,    lr_pwr_lo,    ls_pwr_lo,    ht_pwr_lo,    hrxc_pwr_lo,    hs_pwr_lo,    hisn_pwr_lo,    lp_pwr_lo,    1'b0);
-mux8 mux_pwr_hi			(major_mode, pwr_hi,    lr_pwr_hi,    ls_pwr_hi,    ht_pwr_hi,    hrxc_pwr_hi,    hs_pwr_hi,    hisn_pwr_hi,    lp_pwr_hi,    1'b0);
-mux8 mux_adc_clk		(major_mode, adc_clk,   lr_adc_clk,   ls_adc_clk,   ht_adc_clk,   hrxc_adc_clk,   hs_adc_clk,   hisn_adc_clk,   lp_adc_clk,   1'b0);
-mux8 mux_dbg				(major_mode, dbg,       lr_dbg,       ls_dbg,       ht_dbg,       hrxc_dbg,       hs_dbg,       hisn_dbg,       lp_dbg,       1'b0);
-
-// In all modes, let the ADC's outputs be enabled.
-assign adc_noe = 1'b0;
-
-endmodule
+//-----------------------------------------------------------------------------
+// The FPGA is responsible for interfacing between the A/D, the coil drivers,
+// and the ARM. In the low-frequency modes it passes the data straight
+// through, so that the ARM gets raw A/D samples over the SSP. In the high-
+// frequency modes, the FPGA might perform some demodulation first, to
+// reduce the amount of data that we must send to the ARM.
+//
+// I am not really an FPGA/ASIC designer, so I am sure that a lot of this
+// could be improved.
+//
+// Jonathan Westhues, March 2006
+// Added ISO14443-A support by Gerhard de Koning Gans, April 2008
+//-----------------------------------------------------------------------------
+
+`include "lo_read.v"
+`include "lo_passthru.v"
+`include "lo_simulate.v"
+`include "hi_read_tx.v"
+`include "hi_read_rx_xcorr.v"
+`include "hi_simulate.v"
+`include "hi_iso14443a.v"
+`include "util.v"
+
+module fpga(
+	spcki, miso, mosi, ncs,
+	pck0i, ck_1356meg, ck_1356megb,
+	pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
+	adc_d, adc_clk, adc_noe,
+	ssp_frame, ssp_din, ssp_dout, ssp_clk,
+	cross_hi, cross_lo,
+	dbg
+);
+	input spcki, mosi, ncs;
+	output miso;
+	input pck0i, ck_1356meg, ck_1356megb;
+	output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
+	input [7:0] adc_d;
+	output adc_clk, adc_noe;
+	input ssp_dout;
+	output ssp_frame, ssp_din, ssp_clk;
+	input cross_hi, cross_lo;
+	output dbg;
+
+//assign pck0 = pck0i;
+	IBUFG #(.IOSTANDARD("DEFAULT") ) pck0b(
+		.O(pck0),
+		.I(pck0i)
+	);
+//assign spck = spcki;
+	IBUFG #(.IOSTANDARD("DEFAULT") ) spckb(
+		.O(spck),
+		.I(spcki)
+	);
+//-----------------------------------------------------------------------------
+// The SPI receiver. This sets up the configuration word, which the rest of
+// the logic looks at to determine how to connect the A/D and the coil
+// drivers (i.e., which section gets it). Also assign some symbolic names
+// to the configuration bits, for use below.
+//-----------------------------------------------------------------------------
+
+reg [15:0] shift_reg;
+reg [7:0] divisor;
+reg [7:0] conf_word;
+
+// We switch modes between transmitting to the 13.56 MHz tag and receiving
+// from it, which means that we must make sure that we can do so without
+// glitching, or else we will glitch the transmitted carrier.
+always @(posedge ncs)
+begin
+	case(shift_reg[15:12])
+		4'b0001: conf_word <= shift_reg[7:0];
+		4'b0010: divisor <= shift_reg[7:0];
+	endcase
+end
+
+always @(posedge spck)
+begin
+	if(~ncs)
+	begin
+		shift_reg[15:1] <= shift_reg[14:0];
+		shift_reg[0] <= mosi;
+	end
+end
+
+wire [2:0] major_mode;
+assign major_mode = conf_word[7:5];
+
+// For the low-frequency configuration:
+wire lo_is_125khz;
+assign lo_is_125khz = conf_word[3];
+
+// For the high-frequency transmit configuration: modulation depth, either
+// 100% (just quite driving antenna, steady LOW), or shallower (tri-state
+// some fraction of the buffers)
+wire hi_read_tx_shallow_modulation;
+assign hi_read_tx_shallow_modulation = conf_word[0];
+
+// For the high-frequency receive correlator: frequency against which to
+// correlate.
+wire hi_read_rx_xcorr_848;
+assign hi_read_rx_xcorr_848 = conf_word[0];
+// and whether to drive the coil (reader) or just short it (snooper)
+wire hi_read_rx_xcorr_snoop;
+assign hi_read_rx_xcorr_snoop = conf_word[1];
+
+// Divide the expected subcarrier frequency for hi_read_rx_xcorr by 4
+wire hi_read_rx_xcorr_quarter;
+assign hi_read_rx_xcorr_quarter = conf_word[2];
+
+// For the high-frequency simulated tag: what kind of modulation to use.
+wire [2:0] hi_simulate_mod_type;
+assign hi_simulate_mod_type = conf_word[2:0];
+
+//-----------------------------------------------------------------------------
+// And then we instantiate the modules corresponding to each of the FPGA's
+// major modes, and use muxes to connect the outputs of the active mode to
+// the output pins.
+//-----------------------------------------------------------------------------
+
+lo_read lr(
+	pck0, ck_1356meg, ck_1356megb,
+	lr_pwr_lo, lr_pwr_hi, lr_pwr_oe1, lr_pwr_oe2, lr_pwr_oe3, lr_pwr_oe4,
+	adc_d, lr_adc_clk,
+	lr_ssp_frame, lr_ssp_din, ssp_dout, lr_ssp_clk,
+	cross_hi, cross_lo,
+	lr_dbg,
+	lo_is_125khz, divisor
+);
+
+lo_passthru lp(
+	pck0, ck_1356meg, ck_1356megb,
+	lp_pwr_lo, lp_pwr_hi, lp_pwr_oe1, lp_pwr_oe2, lp_pwr_oe3, lp_pwr_oe4,
+	adc_d, lp_adc_clk,
+	lp_ssp_frame, lp_ssp_din, ssp_dout, lp_ssp_clk,
+	cross_hi, cross_lo,
+	lp_dbg, divisor
+);
+
+lo_simulate ls(
+	pck0, ck_1356meg, ck_1356megb,
+	ls_pwr_lo, ls_pwr_hi, ls_pwr_oe1, ls_pwr_oe2, ls_pwr_oe3, ls_pwr_oe4,
+	adc_d, ls_adc_clk,
+	ls_ssp_frame, ls_ssp_din, ssp_dout, ls_ssp_clk,
+	cross_hi, cross_lo,
+	ls_dbg, divisor
+);
+
+hi_read_tx ht(
+	pck0, ck_1356meg, ck_1356megb,
+	ht_pwr_lo, ht_pwr_hi, ht_pwr_oe1, ht_pwr_oe2, ht_pwr_oe3, ht_pwr_oe4,
+	adc_d, ht_adc_clk,
+	ht_ssp_frame, ht_ssp_din, ssp_dout, ht_ssp_clk,
+	cross_hi, cross_lo,
+	ht_dbg,
+	hi_read_tx_shallow_modulation
+);
+
+hi_read_rx_xcorr hrxc(
+	pck0, ck_1356meg, ck_1356megb,
+	hrxc_pwr_lo, hrxc_pwr_hi, hrxc_pwr_oe1, hrxc_pwr_oe2, hrxc_pwr_oe3,	hrxc_pwr_oe4,
+	adc_d, hrxc_adc_clk,
+	hrxc_ssp_frame, hrxc_ssp_din, ssp_dout, hrxc_ssp_clk,
+	cross_hi, cross_lo,
+	hrxc_dbg,
+	hi_read_rx_xcorr_848, hi_read_rx_xcorr_snoop, hi_read_rx_xcorr_quarter
+);
+
+hi_simulate hs(
+	pck0, ck_1356meg, ck_1356megb,
+	hs_pwr_lo, hs_pwr_hi, hs_pwr_oe1, hs_pwr_oe2, hs_pwr_oe3, hs_pwr_oe4,
+	adc_d, hs_adc_clk,
+	hs_ssp_frame, hs_ssp_din, ssp_dout, hs_ssp_clk,
+	cross_hi, cross_lo,
+	hs_dbg,
+	hi_simulate_mod_type
+);
+
+hi_iso14443a hisn(
+	pck0, ck_1356meg, ck_1356megb,
+	hisn_pwr_lo, hisn_pwr_hi, hisn_pwr_oe1, hisn_pwr_oe2, hisn_pwr_oe3,	hisn_pwr_oe4,
+	adc_d, hisn_adc_clk,
+	hisn_ssp_frame, hisn_ssp_din, ssp_dout, hisn_ssp_clk,
+	cross_hi, cross_lo,
+	hisn_dbg,
+	hi_simulate_mod_type
+);
+
+// Major modes:
+//   000 --  LF reader (generic)
+//   001 --  LF simulated tag (generic)
+//   010 --  HF reader, transmitting to tag; modulation depth selectable
+//   011 --  HF reader, receiving from tag, correlating as it goes; frequency selectable
+//   100 --  HF simulated tag
+//   101 --  HF ISO14443-A
+//   110 --  LF passthrough
+//   111 --  everything off
+
+mux8 mux_ssp_clk		(major_mode, ssp_clk,   lr_ssp_clk,   ls_ssp_clk,   ht_ssp_clk,   hrxc_ssp_clk,   hs_ssp_clk,   hisn_ssp_clk,   lp_ssp_clk,   1'b0);
+mux8 mux_ssp_din		(major_mode, ssp_din,   lr_ssp_din,   ls_ssp_din,   ht_ssp_din,   hrxc_ssp_din,   hs_ssp_din,   hisn_ssp_din,   lp_ssp_din,   1'b0);
+mux8 mux_ssp_frame	(major_mode, ssp_frame, lr_ssp_frame, ls_ssp_frame, ht_ssp_frame, hrxc_ssp_frame, hs_ssp_frame, hisn_ssp_frame, lp_ssp_frame, 1'b0);
+mux8 mux_pwr_oe1		(major_mode, pwr_oe1,   lr_pwr_oe1,   ls_pwr_oe1,   ht_pwr_oe1,   hrxc_pwr_oe1,   hs_pwr_oe1,   hisn_pwr_oe1,   lp_pwr_oe1,   1'b0);
+mux8 mux_pwr_oe2		(major_mode, pwr_oe2,   lr_pwr_oe2,   ls_pwr_oe2,   ht_pwr_oe2,   hrxc_pwr_oe2,   hs_pwr_oe2,   hisn_pwr_oe2,   lp_pwr_oe2,   1'b0);
+mux8 mux_pwr_oe3		(major_mode, pwr_oe3,   lr_pwr_oe3,   ls_pwr_oe3,   ht_pwr_oe3,   hrxc_pwr_oe3,   hs_pwr_oe3,   hisn_pwr_oe3,   lp_pwr_oe3,   1'b0);
+mux8 mux_pwr_oe4		(major_mode, pwr_oe4,   lr_pwr_oe4,   ls_pwr_oe4,   ht_pwr_oe4,   hrxc_pwr_oe4,   hs_pwr_oe4,   hisn_pwr_oe4,   lp_pwr_oe4,   1'b0);
+mux8 mux_pwr_lo			(major_mode, pwr_lo,    lr_pwr_lo,    ls_pwr_lo,    ht_pwr_lo,    hrxc_pwr_lo,    hs_pwr_lo,    hisn_pwr_lo,    lp_pwr_lo,    1'b0);
+mux8 mux_pwr_hi			(major_mode, pwr_hi,    lr_pwr_hi,    ls_pwr_hi,    ht_pwr_hi,    hrxc_pwr_hi,    hs_pwr_hi,    hisn_pwr_hi,    lp_pwr_hi,    1'b0);
+mux8 mux_adc_clk		(major_mode, adc_clk,   lr_adc_clk,   ls_adc_clk,   ht_adc_clk,   hrxc_adc_clk,   hs_adc_clk,   hisn_adc_clk,   lp_adc_clk,   1'b0);
+mux8 mux_dbg				(major_mode, dbg,       lr_dbg,       ls_dbg,       ht_dbg,       hrxc_dbg,       hs_dbg,       hisn_dbg,       lp_dbg,       1'b0);
+
+// In all modes, let the ADC's outputs be enabled.
+assign adc_noe = 1'b0;
+
+endmodule