X-Git-Url: http://cvs.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/b811cc51f9a21324dc7589d1254e767374488a20..6658905f18a1eebc148836f26c731dea9c1377dc:/fpga/lo_read.v

diff --git a/fpga/lo_read.v b/fpga/lo_read.v
new file mode 100644
index 00000000..9c3edb22
--- /dev/null
+++ b/fpga/lo_read.v
@@ -0,0 +1,102 @@
+//-----------------------------------------------------------------------------
+// The way that we connect things in low-frequency read mode. In this case
+// we are generating the 134 kHz or 125 kHz carrier, and running the 
+// unmodulated carrier at that frequency. The A/D samples at that same rate,
+// and the result is serialized.
+//
+// Jonathan Westhues, April 2006
+//-----------------------------------------------------------------------------
+
+module lo_read(
+    pck0, ck_1356meg, ck_1356megb,
+    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
+    adc_d, adc_clk,
+    ssp_frame, ssp_din, ssp_dout, ssp_clk,
+    cross_hi, cross_lo,
+    dbg,
+    lo_is_125khz
+);
+    input pck0, ck_1356meg, ck_1356megb;
+    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
+    input [7:0] adc_d;
+    output adc_clk;
+    input ssp_dout;
+    output ssp_frame, ssp_din, ssp_clk;
+    input cross_hi, cross_lo;
+    output dbg;
+    input lo_is_125khz;
+
+// The low-frequency RFID stuff. This is relatively simple, because most
+// of the work happens on the ARM, and we just pass samples through. The
+// PCK0 must be divided down to generate the A/D clock, and from there by
+// a factor of 8 to generate the carrier (that we apply to the coil drivers).
+//
+// This is also where we decode the received synchronous serial port words,
+// to determine how to drive the output enables.
+
+// PCK0 will run at (PLL clock) / 4, or 24 MHz. That means that we can do
+// 125 kHz by dividing by a further factor of (8*12*2), or ~134 kHz by
+// dividing by a factor of (8*11*2) (for 136 kHz, ~2% error, tolerable).
+
+reg [3:0] pck_divider;
+reg clk_lo;
+
+always @(posedge pck0)
+begin
+    if(lo_is_125khz)
+    begin
+        if(pck_divider == 4'd11)
+        begin
+            pck_divider <= 4'd0;
+            clk_lo = !clk_lo;
+        end
+        else
+            pck_divider <= pck_divider + 1;
+    end
+    else
+    begin
+        if(pck_divider == 4'd10)
+        begin
+            pck_divider <= 4'd0;
+            clk_lo = !clk_lo;
+        end
+        else
+            pck_divider <= pck_divider + 1;
+    end
+end
+
+reg [2:0] carrier_divider_lo;
+
+always @(posedge clk_lo)
+begin
+    carrier_divider_lo <= carrier_divider_lo + 1;
+end
+
+assign pwr_lo = carrier_divider_lo[2];
+
+// This serializes the values returned from the A/D, and sends them out
+// over the SSP.
+
+reg [7:0] to_arm_shiftreg;
+
+always @(posedge clk_lo)
+begin
+    if(carrier_divider_lo == 3'b000)
+        to_arm_shiftreg <= adc_d;
+    else
+        to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
+end
+
+assign ssp_clk = clk_lo;
+assign ssp_frame = (carrier_divider_lo == 3'b001);
+assign ssp_din = to_arm_shiftreg[7];
+
+// The ADC converts on the falling edge, and our serializer loads when
+// carrier_divider_lo == 3'b000.
+assign adc_clk = ~carrier_divider_lo[2];
+
+assign pwr_hi = 1'b0;
+
+assign dbg = adc_clk;
+
+endmodule