X-Git-Url: http://cvs.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/c3963755b7bdb05523e694fbecca4dca2ad0112b..a8904ebd46d747753c9f639f1577694c149ca5c2:/README.txt

diff --git a/README.txt b/README.txt
index 1f506f21..cb2c7f3c 100644
--- a/README.txt
+++ b/README.txt
@@ -1,7 +1,87 @@
-iclass research
-===============
+NOTICE:
+(2014-03-26)
+This is now the official Proxmark repository!
 
-Implemented "hf iclass replay <MAC>" where MAC is 8-char Hexidecimal MAC.
+INTRODUCTION:
 
-Useful to replay a snooped authentication sequence if cc (e-purse) is not correctly updated as per the specification.
-Currently hardset to only read Page 1.
\ No newline at end of file
+The proxmark3 is a powerful general purpose RFID tool, the size of a deck
+of cards, designed to snoop, listen and emulate everything from
+Low Frequency (125kHz) to High Frequency (13.56MHz) tags.
+
+This repository contains enough software, logic (for the FPGA), and design
+documentation for the hardware that you could, at least in theory,
+do something useful with a proxmark3.
+
+RESOURCES:
+
+   * This repository!
+      https://github.com/Proxmark/proxmark3
+      
+   * The Wiki
+      https://github.com/Proxmark/proxmark3/wiki
+      
+   * The GitHub page
+      http://proxmark.github.io/proxmark3/
+      
+   * The Forum
+      http://www.proxmark.org/forum
+      
+   * The IRC chanel
+       irc.freenode.org #proxmark3
+       -or-
+       http://webchat.freenode.net/?channels=#proxmark3
+   
+DEVELOPMENT:
+
+The tools required to build  or run the project will vary depending on
+your operating system. Please refer to the Wiki for details.
+
+   * https://github.com/Proxmark/proxmark3/wiki
+
+OBTAINING HARDWARE:
+
+The Proxmark 3 is available for purcahse (assembled and tested) from the
+following locations:
+
+   * http://proxmark3.com/
+   * http://www.xfpga.com/
+
+Most of the ultra-low-volume contract assemblers could put
+something like this together with a reasonable yield. A run of around
+a dozen units is probably cost-effective. The BOM includes (possibly-
+outdated) component pricing, and everything is available from Digikey
+and the usual distributors.
+
+If you've never assembled a modern circuit board by hand, then this is
+not a good place to start. Some of the components (e.g. the crystals)
+must not be assembled with a soldering iron, and require hot air.
+
+The schematics are included; the component values given are not
+necessarily correct for all situations, but it should be possible to do
+nearly anything you would want with appropriate population options.
+
+The printed circuit board artwork is also available, as Gerbers and an
+Excellon drill file.
+
+
+LICENSING:
+
+This program is free software; you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation; either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program; if not, write to the Free Software
+Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+
+
+Jonathan Westhues
+user jwesthues, at host cq.cx
+
+May 2007, Cambridge MA