dos2unix *.vhd

[raggedstone] / dhwk / source / config_rd_0.vhd

-- J.STELZNER
-- INFORMATIK-3 LABOR
-- 23.08.2006
-- File: CONFIG_RD_0.VHD

library IEEE;
use IEEE.std_logic_1164.all;

entity CONFIG_RD_0 is
    port
	(
	ADDR_REG	:in		std_logic_vector (31 downto 0);
	CF_RD_COM	:in		std_logic;
	READ_SEL	:out	std_logic_vector ( 2 downto 0)
    );
end entity CONFIG_RD_0;

architecture CONFIG_RD_0_DESIGN of CONFIG_RD_0 is

--
--
--
--
--
--		               PCI Configuration Space Header
--
--            \                        Bit
--			   \
--Address		|31		  24|23		  16|15		   8|7		   0|      
-----------------------------------------------------------------
--00			|Device ID				|Vendor ID				|					
--04			|Status					|Command				|
--08			|Class Code				 			|Revision ID|
--0C			|BIST		|Header Type|Latency T. |Cache L.S.	|
--10-24			|Base Address Register							|
--28			|Cardbus CIS Pointer							|
--2C			|Subsystem ID			|Subsystem Vendor ID	|
--30			|Expansion ROM Base Address						|
--34			|Reserved										|
--38			|Reserved										|
--3C			|Max_Lat	|Min_Gnt	|Int_Pin	|Int_Line	|
--40-FF			|												|
-----------------------------------------------------------------


--PCI Bus Commands 
--C/BE[3..0] Command Type
--------------------------------------
--	0000		Interrupt Acknowledge
--	0001		Special Cycle
--	0010		I/O Read
--	0011		I/O Write
--	0100		Reserved
--	0101		Reserved
--	0110		Memory Read
--	0111		Memory Write
--
--	1000		Reserved
--	1001		Reserved
--	1010		Configuration Read
--	1011		Configuration Write
--	1100		Memory Read Multiple 
--	1101		Dual Address Cycle
--	1110		Memory Read Line
--	1111		Memory Write and Invalidate


--PCI Byte Enable 
--C/BE[3..0] gueltige Datenbits 
-------------------------------
--	0000		AD 31..0
--	1000		AD 23..0
--	1100		AD 15..0
--	1110		AD  7..0

	constant	CMD_INT_ACK			:std_logic_vector(3 downto 0) := "0000";
	constant	CMD_SP_CYC			:std_logic_vector(3 downto 0) := "0001";
	constant	CMD_IO_READ			:std_logic_vector(3 downto 0) := "0010";
	constant	CMD_IO_WRITE		:std_logic_vector(3 downto 0) := "0011";
	constant	CMD_RES_4				:std_logic_vector(3 downto 0) := "0100";
	constant	CMD_RES_5				:std_logic_vector(3 downto 0) := "0101";
	constant	CMD_MEM_READ		:std_logic_vector(3 downto 0) := "0110";
	constant	CMD_MEM_WRITE		:std_logic_vector(3 downto 0) := "0111";
	constant	CMD_RES_8				:std_logic_vector(3 downto 0) := "1000";
	constant	CMD_RES_9				:std_logic_vector(3 downto 0) := "1001";
	constant	CMD_CONF_READ		:std_logic_vector(3 downto 0) := "1010";
	constant	CMD_CONF_WRITE	:std_logic_vector(3 downto 0) := "1011";
	constant	CMD_MEM_READ_M	:std_logic_vector(3 downto 0) := "1100";
	constant	CMD_DU_ADR_CYC	:std_logic_vector(3 downto 0) := "1101";
	constant	CMD_MEN_READ_L	:std_logic_vector(3 downto 0) := "1110";
	constant	CMD_MEM_WRITE_I	:std_logic_vector(3 downto 0) := "1111";

	signal		MUX							:std_logic_vector(31 downto 0); 
	signal		CONFIG_ADDR			:std_logic_vector( 7 downto 0); 

begin

	CONFIG_ADDR(7 downto 0) <= ADDR_REG(7 downto 0);

--*******************************************************************
--*********************** PCI Read Address **************************
--*******************************************************************

	process (CF_RD_COM, CONFIG_ADDR) 
	begin

		if	CF_RD_COM = '1'	then

			if		CONFIG_ADDR = X"00"	then	READ_SEL <= "000";
			elsif	CONFIG_ADDR = X"04"	then	READ_SEL <= "001";
			elsif	CONFIG_ADDR = X"08"	then	READ_SEL <= "010";
			elsif	CONFIG_ADDR = X"10"	then	READ_SEL <= "011";
			elsif	CONFIG_ADDR = X"3C"	then	READ_SEL <= "100";
			elsif	CONFIG_ADDR = X"40"	then	READ_SEL <= "101";
			else								READ_SEL <= "111";
			end if;
		else									READ_SEL <= "111";
		end if;
	end process;

end architecture CONFIG_RD_0_DESIGN;