code cleanup

[raggedstone] / dhwk / source / config_rd_0.vhd

-- J.STELZNER\r
-- INFORMATIK-3 LABOR\r
-- 23.08.2006\r
-- File: CONFIG_RD_0.VHD\r
\r
library IEEE;\r
use IEEE.std_logic_1164.all;\r
\r
entity CONFIG_RD_0 is\r
    port\r
	(\r
	ADDR_REG	:in		std_logic_vector (31 downto 0);\r
	CF_RD_COM	:in		std_logic;\r
	READ_SEL	:out	std_logic_vector ( 2 downto 0)\r
    );\r
end entity CONFIG_RD_0;\r
\r
architecture CONFIG_RD_0_DESIGN of CONFIG_RD_0 is\r
\r
--\r
--\r
--\r
--\r
--\r
--		               PCI Configuration Space Header\r
--\r
--            \                        Bit\r
--			   \\r
--Address		|31		  24|23		  16|15		   8|7		   0|      \r
-----------------------------------------------------------------\r
--00			|Device ID				|Vendor ID				|					\r
--04			|Status					|Command				|\r
--08			|Class Code				 			|Revision ID|\r
--0C			|BIST		|Header Type|Latency T. |Cache L.S.	|\r
--10-24			|Base Address Register							|\r
--28			|Cardbus CIS Pointer							|\r
--2C			|Subsystem ID			|Subsystem Vendor ID	|\r
--30			|Expansion ROM Base Address						|\r
--34			|Reserved										|\r
--38			|Reserved										|\r
--3C			|Max_Lat	|Min_Gnt	|Int_Pin	|Int_Line	|\r
--40-FF			|												|\r
-----------------------------------------------------------------\r
\r
\r
--PCI Bus Commands \r
--C/BE[3..0] Command Type\r
--------------------------------------\r
--	0000		Interrupt Acknowledge\r
--	0001		Special Cycle\r
--	0010		I/O Read\r
--	0011		I/O Write\r
--	0100		Reserved\r
--	0101		Reserved\r
--	0110		Memory Read\r
--	0111		Memory Write\r
--\r
--	1000		Reserved\r
--	1001		Reserved\r
--	1010		Configuration Read\r
--	1011		Configuration Write\r
--	1100		Memory Read Multiple \r
--	1101		Dual Address Cycle\r
--	1110		Memory Read Line\r
--	1111		Memory Write and Invalidate\r
\r
\r
--PCI Byte Enable \r
--C/BE[3..0] gueltige Datenbits \r
-------------------------------\r
--	0000		AD 31..0\r
--	1000		AD 23..0\r
--	1100		AD 15..0\r
--	1110		AD  7..0\r
\r
	constant	CMD_INT_ACK			:std_logic_vector(3 downto 0) := "0000";\r
	constant	CMD_SP_CYC			:std_logic_vector(3 downto 0) := "0001";\r
	constant	CMD_IO_READ			:std_logic_vector(3 downto 0) := "0010";\r
	constant	CMD_IO_WRITE		:std_logic_vector(3 downto 0) := "0011";\r
	constant	CMD_RES_4				:std_logic_vector(3 downto 0) := "0100";\r
	constant	CMD_RES_5				:std_logic_vector(3 downto 0) := "0101";\r
	constant	CMD_MEM_READ		:std_logic_vector(3 downto 0) := "0110";\r
	constant	CMD_MEM_WRITE		:std_logic_vector(3 downto 0) := "0111";\r
	constant	CMD_RES_8				:std_logic_vector(3 downto 0) := "1000";\r
	constant	CMD_RES_9				:std_logic_vector(3 downto 0) := "1001";\r
	constant	CMD_CONF_READ		:std_logic_vector(3 downto 0) := "1010";\r
	constant	CMD_CONF_WRITE	:std_logic_vector(3 downto 0) := "1011";\r
	constant	CMD_MEM_READ_M	:std_logic_vector(3 downto 0) := "1100";\r
	constant	CMD_DU_ADR_CYC	:std_logic_vector(3 downto 0) := "1101";\r
	constant	CMD_MEN_READ_L	:std_logic_vector(3 downto 0) := "1110";\r
	constant	CMD_MEM_WRITE_I	:std_logic_vector(3 downto 0) := "1111";\r
\r
	signal		MUX							:std_logic_vector(31 downto 0); \r
	signal		CONFIG_ADDR			:std_logic_vector( 7 downto 0); \r
\r
begin\r
\r
	CONFIG_ADDR(7 downto 0) <= ADDR_REG(7 downto 0);\r
\r
--*******************************************************************\r
--*********************** PCI Read Address **************************\r
--*******************************************************************\r
\r
	process (CF_RD_COM, CONFIG_ADDR) \r
	begin\r
\r
		if	CF_RD_COM = '1'	then\r
\r
			if		CONFIG_ADDR = X"00"	then	READ_SEL <= "000";\r
			elsif	CONFIG_ADDR = X"04"	then	READ_SEL <= "001";\r
			elsif	CONFIG_ADDR = X"08"	then	READ_SEL <= "010";\r
			elsif	CONFIG_ADDR = X"10"	then	READ_SEL <= "011";\r
			elsif	CONFIG_ADDR = X"3C"	then	READ_SEL <= "100";\r
			elsif	CONFIG_ADDR = X"40"	then	READ_SEL <= "101";\r
			else								READ_SEL <= "111";\r
			end if;\r
		else									READ_SEL <= "111";\r
		end if;\r
	end process;\r
\r
end architecture CONFIG_RD_0_DESIGN;\r
\r