it works on ISE Webpack 9.1SP3

[usb-driver] / README

diff --git a/README b/README
index 8d3ca256405fb8f592e7b04e0cb5c109fa595b6c..13737b53039f8a816b70561d28ea0a20ea8518fa 100644 (file)
--- a/README
+++ b/README
@@ -1,15 +1,21 @@
-This library emulates Jungo Windrvr USB functions in userspace which are
-required by XILINX impact to access the Platform cable USB. With this library
-it is possible to access the cable without loading a proprietary kernel module
-which breaks with every new kernel release. It uses the USB functions provided
-by the libusb userspace library instead and should work on every kernel version
-which is supported by libusb. It was written against impact from ISE Webpack
-9.1SP1 and tested with the following software:
+This library emulates Jungo Windrvr USB and parallel port functions in
+userspace which are required by XILINX impact to access the Platform cable USB
+and Parallel Cable III.
+With this library it is possible to access the cables without loading a
+proprietary kernel module which breaks with every new kernel release. It uses
+the functionality provided by the libusb userspace library for USB access and
+the kernel interface at /dev/parport0 for parallel port access instead and
+should work on every kernel version which is supported by libusb and supports
+ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
+the following software:

 
 

+ * ISE Webpack 9.1SP3

  * ISE Webpack 9.1SP2
  * ISE Webpack 9.1SP1
  * ISE Webpack 9.1SP2
  * ISE Webpack 9.1SP1

+ * ISE Webpack 8.2SP3

  * ISE Webpack 8.1SP3
  * ChipScope 9.1.02i
  * ISE Webpack 8.1SP3
  * ChipScope 9.1.02i

+ * EDK 8.2.02i

 
 Build the library by calling `make'.
 
 
 Build the library by calling `make'.
 


@@ -21,7 +27,14 @@ $ export LD_PRELOAD=/path/to/libusb-driver.so  (for sh shells)
 $ setenv LD_PRELOAD /path/to/libusb-driver.so  (for csh shells)
 $ impact
 
 $ setenv LD_PRELOAD /path/to/libusb-driver.so  (for csh shells)
 $ impact
 

-To use the device as ordinary user, put the following line in a new
+The source for this library can be found at:
+http://cvs.zerfleddert.de/cgi-bin/viewcvs.cgi/usb-driver/
+
+
+Notes for the USB cable
+=======================
+
+To use the device as an ordinary user, put the following line in a new

 file in /etc/udev/rules.d/ and restart udev:
 ACTION=="add", BUS=="usb", SYSFS{idVendor}=="03fd", MODE="666"
 
 file in /etc/udev/rules.d/ and restart udev:
 ACTION=="add", BUS=="usb", SYSFS{idVendor}=="03fd", MODE="666"
 


@@ -40,3 +53,35 @@ these steps:
 3. copy the file /path/to/ISE/bin/lin/xusbdfwu.hex to /usr/share/xusbdfwu.hex
 
 4. restart udev and re-plug the cable
 3. copy the file /path/to/ISE/bin/lin/xusbdfwu.hex to /usr/share/xusbdfwu.hex
 
 4. restart udev and re-plug the cable

+
+
+Notes for the parallel cable
+============================
+
+To access the parallel port from userspace, the kernel needs to be built with
+the features "Parallel port support" (CONFIG_PARPORT), "PC-style hardware"
+(CONFIG_PARPORT_PC) and "Support for user-space parallel port device drivers"
+(CONFIG_PPDEV) builtin or as modules. If these features are built as modules,
+they need to be loaded before using this library.
+These modules are called:
+parport
+parport_pc
+ppdev
+
+
+To use the device as an ordinary user, put the user in the group 'lp'
+
+
+Parallel Cable IV is currently only supported in 'compatibility mode', as no
+attempt to configure the ECP registers is done by this library.
+
+
+If you get "Programming failed" or "DONE did not go high" when programming
+through the parallel cable with Impact 9.1, make sure to have the option "Use
+HIGHZ instead of BYPASS" enabled in Edit -> Preferences -> iMPACT Configuration
+Preferences.
+If you are using batch mode, add the following line to your cmd file:
+setPreference -pref UseHighz:TRUE
+(This problem also occurs on windows and when using the real windrvr in linux and
+is solved with the same workaround. Impact 8.2 is working fine with the same
+boards and designs)