cvs.zerfleddert.de Git - proxmark3-svn/blob - fpga/lf_edge_detect.v

   1 //-----------------------------------------------------------------------------
   2 // Copyright (C) 2014 iZsh <izsh at fail0verflow.com>
   3 //
   4 // This code is licensed to you under the terms of the GNU GPL, version 2 or,
   5 // at your option, any later version. See the LICENSE.txt file for the text of
   6 // the license.
   7 //-----------------------------------------------------------------------------
   8 // input clk is 24Mhz
   9 `include "min_max_tracker.v"
  10
  11 module lf_edge_detect(input clk, input [7:0] adc_d, input [7:0] lf_ed_threshold,
  12         output [7:0] max, output [7:0] min,
  13         output [7:0] high_threshold, output [7:0] highz_threshold,
  14         output [7:0] lowz_threshold, output [7:0] low_threshold,
  15         output edge_state, output edge_toggle);
  16
  17         min_max_tracker tracker(clk, adc_d, lf_ed_threshold, min, max);
  18
  19         // auto-tune
  20         assign high_threshold = (max + min) / 2 + (max - min) / 4;
  21         assign highz_threshold = (max + min) / 2 + (max - min) / 8;
  22         assign lowz_threshold = (max + min) / 2 - (max - min) / 8;
  23         assign low_threshold = (max + min) / 2 - (max - min) / 4;
  24
  25         // heuristic to see if it makes sense to try to detect an edge
  26         wire enabled =
  27                 (high_threshold > highz_threshold)
  28                 & (highz_threshold > lowz_threshold)
  29                 & (lowz_threshold > low_threshold)
  30                 & ((high_threshold - highz_threshold) > 8)
  31                 & ((highz_threshold - lowz_threshold) > 16)
  32                 & ((lowz_threshold - low_threshold) > 8);
  33
  34         // Toggle the output with hysteresis
  35         // Set to high if the ADC value is above the threshold
  36         // Set to low if the ADC value is below the threshold
  37         reg is_high = 0;
  38         reg is_low = 0;
  39         reg is_zero = 0;
  40         reg trigger_enabled = 1;
  41         reg output_edge = 0;
  42         reg output_state;
  43
  44         always @(posedge clk)
  45         begin
  46                 is_high <= (adc_d >= high_threshold);
  47                 is_low <= (adc_d <= low_threshold);
  48                 is_zero <= ((adc_d > lowz_threshold) & (adc_d < highz_threshold));
  49         end
  50
  51         // all edges detection
  52         always @(posedge clk)
  53         if (enabled) begin
  54                 // To enable detecting two consecutive peaks at the same level
  55                 // (low or high) we check whether or not we went back near 0 in-between.
  56                 // This extra check is necessary to prevent from noise artifacts
  57                 // around the threshold values.
  58                 if (trigger_enabled & (is_high | is_low)) begin
  59                         output_edge <= ~output_edge;
  60                         trigger_enabled <= 0;
  61                 end else
  62                         trigger_enabled <= trigger_enabled | is_zero;
  63         end
  64
  65         // edge states
  66         always @(posedge clk)
  67         if (enabled) begin
  68                 if (is_high)
  69                         output_state <= 1'd1;
  70                 else if (is_low)
  71                         output_state <= 1'd0;
  72         end
  73
  74         assign edge_state = output_state;
  75         assign edge_toggle = output_edge;
  76
  77 endmodule