cvs.zerfleddert.de Git - proxmark3-svn/blob - bootrom/bootrom.c

   1 #include <proxmark3.h>
   2
   3 static void ConfigClocks(void)
   4 {
   5     // we are using a 16 MHz crystal as the basis for everything
   6     // slow clock runs at 32Khz typical regardless of crystal
   7
   8     // enable system clock and USB clock
   9     PMC_SYS_CLK_ENABLE = PMC_SYS_CLK_PROCESSOR_CLK | PMC_SYS_CLK_UDP_CLK;
  10
  11         // enable the clock to the following peripherals
  12     PMC_PERIPHERAL_CLK_ENABLE =
  13         (1<<PERIPH_PIOA) |
  14         (1<<PERIPH_ADC) |
  15         (1<<PERIPH_SPI) |
  16         (1<<PERIPH_SSC) |
  17         (1<<PERIPH_PWMC) |
  18         (1<<PERIPH_UDP);
  19
  20         // worst case scenario, with 16Mhz xtal startup delay is 14.5ms
  21         // with a slow clock running at it worst case (max) frequency of 42khz
  22         // max startup delay = (14.5ms*42k)/8 = 76 = 0x4C round up to 0x50
  23
  24         // enable main oscillator and set startup delay
  25     PMC_MAIN_OSCILLATOR = PMC_MAIN_OSCILLATOR_ENABLE |
  26         PMC_MAIN_OSCILLATOR_STARTUP_DELAY(0x50);
  27
  28         // wait for main oscillator to stabilize
  29         while ( !(PMC_INTERRUPT_STATUS & PMC_MAIN_OSCILLATOR_STABILIZED) )
  30                 ;
  31
  32     // minimum PLL clock frequency is 80 MHz in range 00 (96 here so okay)
  33     // frequency is crystal * multiplier / divisor = 16Mhz * 12 / 2 = 96Mhz
  34     PMC_PLL = PMC_PLL_DIVISOR(2) | PMC_PLL_COUNT_BEFORE_LOCK(0x50) |
  35         PMC_PLL_FREQUENCY_RANGE(0) | PMC_PLL_MULTIPLIER(12) |
  36         PMC_PLL_USB_DIVISOR(1);
  37
  38         // wait for PLL to lock
  39         while ( !(PMC_INTERRUPT_STATUS & PMC_MAIN_OSCILLATOR_PLL_LOCK) )
  40                 ;
  41
  42         // we want a master clock (MCK) to be PLL clock / 2 = 96Mhz / 2 = 48Mhz
  43         // as per datasheet, this register must be programmed in two operations
  44         // when changing to PLL, program the prescaler first then the source
  45     PMC_MASTER_CLK = PMC_CLK_PRESCALE_DIV_2;
  46
  47         // wait for main clock ready signal
  48         while ( !(PMC_INTERRUPT_STATUS & PMC_MAIN_OSCILLATOR_MCK_READY) )
  49                 ;
  50
  51         // set the source to PLL
  52     PMC_MASTER_CLK = PMC_CLK_SELECTION_PLL_CLOCK | PMC_CLK_PRESCALE_DIV_2;
  53
  54         // wait for main clock ready signal
  55         while ( !(PMC_INTERRUPT_STATUS & PMC_MAIN_OSCILLATOR_MCK_READY) )
  56                 ;
  57 }
  58
  59 static void Fatal(void)
  60 {
  61     for(;;);
  62 }
  63
  64 void UsbPacketReceived(BYTE *packet, int len)
  65 {
  66     int i;
  67     UsbCommand *c = (UsbCommand *)packet;
  68     volatile DWORD *p;
  69
  70     if(len != sizeof(*c)) {
  71         Fatal();
  72     }
  73
  74     switch(c->cmd) {
  75         case CMD_DEVICE_INFO:
  76             break;
  77
  78         case CMD_SETUP_WRITE:
  79             p = (volatile DWORD *)0;
  80             for(i = 0; i < 12; i++) {
  81                 p[i+c->ext1] = c->d.asDwords[i];
  82             }
  83             break;
  84
  85         case CMD_FINISH_WRITE:
  86             p = (volatile DWORD *)0;
  87             for(i = 0; i < 4; i++) {
  88                 p[i+60] = c->d.asDwords[i];
  89             }
  90
  91             MC_FLASH_COMMAND = MC_FLASH_COMMAND_KEY |
  92                 MC_FLASH_COMMAND_PAGEN(c->ext1/FLASH_PAGE_SIZE_BYTES) |
  93                 FCMD_WRITE_PAGE;
  94             while(!(MC_FLASH_STATUS & MC_FLASH_STATUS_READY))
  95                 ;
  96             break;
  97
  98         case CMD_HARDWARE_RESET:
  99             break;
 100
 101         default:
 102             Fatal();
 103             break;
 104     }
 105
 106     c->cmd = CMD_ACK;
 107     UsbSendPacket(packet, len);
 108 }
 109
 110 void BootROM(void)
 111 {
 112     //------------
 113     // First set up all the I/O pins; GPIOs configured directly, other ones
 114     // just need to be assigned to the appropriate peripheral.
 115
 116     // Kill all the pullups, especially the one on USB D+; leave them for
 117     // the unused pins, though.
 118     PIO_NO_PULL_UP_ENABLE =     (1 << GPIO_USB_PU)          |
 119                                 (1 << GPIO_LED_A)           |
 120                                 (1 << GPIO_LED_B)           |
 121                                 (1 << GPIO_LED_C)           |
 122                                 (1 << GPIO_LED_D)           |
 123                                 (1 << GPIO_FPGA_DIN)        |
 124                                 (1 << GPIO_FPGA_DOUT)       |
 125                                 (1 << GPIO_FPGA_CCLK)       |
 126                                 (1 << GPIO_FPGA_NINIT)      |
 127                                 (1 << GPIO_FPGA_NPROGRAM)   |
 128                                 (1 << GPIO_FPGA_DONE)       |
 129                                 (1 << GPIO_MUXSEL_HIPKD)    |
 130                                 (1 << GPIO_MUXSEL_HIRAW)    |
 131                                 (1 << GPIO_MUXSEL_LOPKD)    |
 132                                 (1 << GPIO_MUXSEL_LORAW)    |
 133                                 (1 << GPIO_RELAY)               |
 134                                 (1 << GPIO_NVDD_ON);
 135                                 // (and add GPIO_FPGA_ON)
 136         // These pins are outputs
 137     PIO_OUTPUT_ENABLE =         (1 << GPIO_LED_A)           |
 138                                 (1 << GPIO_LED_B)           |
 139                                 (1 << GPIO_LED_C)           |
 140                                 (1 << GPIO_LED_D)           |
 141                                 (1 << GPIO_RELAY)               |
 142                                 (1 << GPIO_NVDD_ON);
 143         // PIO controls the following pins
 144     PIO_ENABLE =                (1 << GPIO_USB_PU)          |
 145                                 (1 << GPIO_LED_A)           |
 146                                 (1 << GPIO_LED_B)           |
 147                                 (1 << GPIO_LED_C)           |
 148                                 (1 << GPIO_LED_D);
 149
 150     USB_D_PLUS_PULLUP_OFF();
 151     LED_D_OFF();
 152     LED_C_ON();
 153     LED_B_OFF();
 154     LED_A_OFF();
 155
 156         // if 512K FLASH part - TODO make some defines :)
 157         if ((DBGU_CIDR | 0xf00) == 0xa00) {
 158                 MC_FLASH_MODE0 = MC_FLASH_MODE_FLASH_WAIT_STATES(1) |
 159                         MC_FLASH_MODE_MASTER_CLK_IN_MHZ(0x48);
 160                 MC_FLASH_MODE1 = MC_FLASH_MODE_FLASH_WAIT_STATES(1) |
 161                         MC_FLASH_MODE_MASTER_CLK_IN_MHZ(0x48);
 162         } else {
 163                 MC_FLASH_MODE0 = MC_FLASH_MODE_FLASH_WAIT_STATES(0) |
 164                         MC_FLASH_MODE_MASTER_CLK_IN_MHZ(48);
 165         }
 166
 167         // Initialize all system clocks
 168     ConfigClocks();
 169
 170     LED_A_ON();
 171
 172         if(BUTTON_PRESS()) {
 173         UsbStart();
 174         }
 175
 176     for(;;) {
 177         WDT_HIT();
 178
 179         UsbPoll(TRUE);
 180
 181                 if(!BUTTON_PRESS()) {
 182             USB_D_PLUS_PULLUP_OFF();
 183             LED_B_ON();
 184
 185                         // jump to RAM address 0x10000 (LSBit set for thumb mode)
 186             asm("ldr r3, = 0x10001\n");
 187             asm("bx r3\n");
 188         }
 189     }
 190 }