cvs.zerfleddert.de Git - proxmark3-svn/blob - bootrom/bootrom.c

   1 //-----------------------------------------------------------------------------
   2 // This code is licensed to you under the terms of the GNU GPL, version 2 or,
   3 // at your option, any later version. See the LICENSE.txt file for the text of
   4 // the license.
   5 //-----------------------------------------------------------------------------
   6 // Main code for the bootloader
   7 //-----------------------------------------------------------------------------
   8
   9 #include "proxmark3.h"
  10 #include "usb_cdc.h"
  11
  12 void DbpString(char *str) {
  13   uint8_t len = 0;
  14   while (str[len] != 0x00) {
  15     len++;
  16   }
  17   cmd_send_old(CMD_DEBUG_PRINT_STRING,len,0,0,(uint8_t*)str,len);
  18 }
  19
  20 struct common_area common_area __attribute__((section(".commonarea")));
  21 unsigned int start_addr, end_addr, bootrom_unlocked;
  22 extern char _bootrom_start, _bootrom_end, _flash_start, _flash_end;
  23
  24 static void ConfigClocks(void)
  25 {
  26     // we are using a 16 MHz crystal as the basis for everything
  27     // slow clock runs at 32Khz typical regardless of crystal
  28
  29     // enable system clock and USB clock
  30     AT91C_BASE_PMC->PMC_SCER = AT91C_PMC_PCK | AT91C_PMC_UDP;
  31
  32         // enable the clock to the following peripherals
  33     AT91C_BASE_PMC->PMC_PCER =
  34                 (1<<AT91C_ID_PIOA)      |
  35                 (1<<AT91C_ID_ADC)       |
  36                 (1<<AT91C_ID_SPI)       |
  37                 (1<<AT91C_ID_SSC)       |
  38                 (1<<AT91C_ID_PWMC)      |
  39                 (1<<AT91C_ID_UDP);
  40
  41         // worst case scenario, with MAINCK = 16Mhz xtal, startup delay is 1.4ms
  42         // if SLCK slow clock runs at its worst case (max) frequency of 42khz
  43         // max startup delay = (1.4ms*42k)/8 = 7.356 so round up to 8
  44
  45         // enable main oscillator and set startup delay
  46     AT91C_BASE_PMC->PMC_MOR =
  47         AT91C_CKGR_MOSCEN |
  48         PMC_MAIN_OSC_STARTUP_DELAY(8);
  49
  50         // wait for main oscillator to stabilize
  51         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MOSCS) )
  52                 ;
  53
  54     // PLL output clock frequency in range  80 - 160 MHz needs CKGR_PLL = 00
  55     // PLL output clock frequency in range 150 - 180 MHz needs CKGR_PLL = 10
  56     // PLL output is MAINCK * multiplier / divisor = 16Mhz * 12 / 2 = 96Mhz
  57     AT91C_BASE_PMC->PMC_PLLR =
  58         PMC_PLL_DIVISOR(2) |
  59                 PMC_PLL_COUNT_BEFORE_LOCK(0x50) |
  60                 PMC_PLL_FREQUENCY_RANGE(0) |
  61                 PMC_PLL_MULTIPLIER(12) |
  62                 PMC_PLL_USB_DIVISOR(1);
  63
  64         // wait for PLL to lock
  65         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_LOCK) )
  66                 ;
  67
  68         // we want a master clock (MCK) to be PLL clock / 2 = 96Mhz / 2 = 48Mhz
  69         // datasheet recommends that this register is programmed in two operations
  70         // when changing to PLL, program the prescaler first then the source
  71     AT91C_BASE_PMC->PMC_MCKR = AT91C_PMC_PRES_CLK_2;
  72
  73         // wait for main clock ready signal
  74         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY) )
  75                 ;
  76
  77         // set the source to PLL
  78     AT91C_BASE_PMC->PMC_MCKR = AT91C_PMC_PRES_CLK_2 | AT91C_PMC_CSS_PLL_CLK;
  79
  80         // wait for main clock ready signal
  81         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY) )
  82                 ;
  83 }
  84
  85 static void Fatal(void)
  86 {
  87   for(;;);
  88 }
  89
  90 void UsbPacketReceived(UsbCommand *c) {
  91   int i, dont_ack=0;
  92   volatile uint32_t *p;
  93
  94   uint32_t arg0 = (uint32_t)c->arg[0];
  95
  96   switch(c->cmd) {
  97     case CMD_DEVICE_INFO: {
  98       dont_ack = 1;
  99       arg0 = DEVICE_INFO_FLAG_BOOTROM_PRESENT
 100                 | DEVICE_INFO_FLAG_CURRENT_MODE_BOOTROM
 101                 | DEVICE_INFO_FLAG_UNDERSTANDS_START_FLASH;
 102       if(common_area.flags.osimage_present) {
 103         arg0 |= DEVICE_INFO_FLAG_OSIMAGE_PRESENT;
 104       }
 105       cmd_send_old(CMD_DEVICE_INFO,arg0,1,2,0,0);
 106     } break;
 107
 108     case CMD_SETUP_WRITE: {
 109       /* The temporary write buffer of the embedded flash controller is mapped to the
 110        * whole memory region, only the last 8 bits are decoded.
 111        */
 112       p = (volatile uint32_t *)&_flash_start;
 113       for(i = 0; i < 12; i++) {
 114         p[i+arg0] = c->d.asDwords[i];
 115       }
 116     } break;
 117
 118     case CMD_FINISH_WRITE: {
 119       uint32_t* flash_mem = (uint32_t*)(&_flash_start);
 120       for (size_t j=0; j<2; j++) {
 121         for(i = 0+(64*j); i < 64+(64*j); i++) {
 122           flash_mem[i] = c->d.asDwords[i];
 123         }
 124
 125         uint32_t flash_address = arg0 + (0x100*j);
 126
 127         /* Check that the address that we are supposed to write to is within our allowed region */
 128         if( ((flash_address+AT91C_IFLASH_PAGE_SIZE-1) >= end_addr) || (flash_address < start_addr) ) {
 129           /* Disallow write */
 130           dont_ack = 1;
 131           cmd_send_old(CMD_NACK,0,0,0,0,0);
 132         } else {
 133           uint32_t page_n = (flash_address - ((uint32_t)flash_mem)) / AT91C_IFLASH_PAGE_SIZE;
 134           /* Translate address to flash page and do flash, update here for the 512k part */
 135           AT91C_BASE_EFC0->EFC_FCR = MC_FLASH_COMMAND_KEY |
 136           MC_FLASH_COMMAND_PAGEN(page_n) |
 137           AT91C_MC_FCMD_START_PROG;
 138         }
 139
 140         // Wait until flashing of page finishes
 141         uint32_t sr;
 142         while(!((sr = AT91C_BASE_EFC0->EFC_FSR) & AT91C_MC_FRDY));
 143         if(sr & (AT91C_MC_LOCKE | AT91C_MC_PROGE)) {
 144           dont_ack = 1;
 145           cmd_send_old(CMD_NACK,0,0,0,0,0);
 146         }
 147       }
 148     } break;
 149
 150     case CMD_HARDWARE_RESET: {
 151       usb_disable();
 152       AT91C_BASE_RSTC->RSTC_RCR = RST_CONTROL_KEY | AT91C_RSTC_PROCRST;
 153     } break;
 154
 155     case CMD_START_FLASH: {
 156       if(c->arg[2] == START_FLASH_MAGIC) bootrom_unlocked = 1;
 157       else bootrom_unlocked = 0;
 158       {
 159         int prot_start = (int)&_bootrom_start;
 160         int prot_end = (int)&_bootrom_end;
 161         int allow_start = (int)&_flash_start;
 162         int allow_end = (int)&_flash_end;
 163         int cmd_start = c->arg[0];
 164         int cmd_end = c->arg[1];
 165
 166         /* Only allow command if the bootrom is unlocked, or the parameters are outside of the protected
 167          * bootrom area. In any case they must be within the flash area.
 168          */
 169         if( (bootrom_unlocked || ((cmd_start >= prot_end) || (cmd_end < prot_start)))
 170            && (cmd_start >= allow_start) && (cmd_end <= allow_end) ) {
 171           start_addr = cmd_start;
 172           end_addr = cmd_end;
 173         } else {
 174           start_addr = end_addr = 0;
 175           dont_ack = 1;
 176           cmd_send_old(CMD_NACK,0,0,0,0,0);
 177         }
 178       }
 179     } break;
 180
 181     default: {
 182       Fatal();
 183     } break;
 184   }
 185
 186   if(!dont_ack) {
 187     cmd_send_old(CMD_ACK,arg0,0,0,0,0);
 188   }
 189 }
 190
 191 static void flash_mode(int externally_entered)
 192 {
 193         start_addr = 0;
 194         end_addr = 0;
 195         bootrom_unlocked = 0;
 196     UsbCommand rx;
 197
 198         usb_enable();
 199         for (volatile size_t i=0; i<0x100000; i++) {};
 200
 201         for(;;) {
 202                 WDT_HIT();
 203
 204                 if (cmd_receive(&rx)) {
 205                         UsbPacketReceived(&rx);
 206                 }
 207
 208                 if(!externally_entered && !BUTTON_PRESS()) {
 209                         /* Perform a reset to leave flash mode */
 210       usb_disable();
 211                         LED_B_ON();
 212                         AT91C_BASE_RSTC->RSTC_RCR = RST_CONTROL_KEY | AT91C_RSTC_PROCRST;
 213                         for(;;);
 214                 }
 215                 if(externally_entered && BUTTON_PRESS()) {
 216                         /* Let the user's button press override the automatic leave */
 217                         externally_entered = 0;
 218                 }
 219         }
 220 }
 221
 222 extern uint32_t _osimage_entry;
 223 void BootROM(void)
 224 {
 225     //------------
 226     // First set up all the I/O pins; GPIOs configured directly, other ones
 227     // just need to be assigned to the appropriate peripheral.
 228
 229     // Kill all the pullups, especially the one on USB D+; leave them for
 230     // the unused pins, though.
 231     AT91C_BASE_PIOA->PIO_PPUDR =
 232         GPIO_USB_PU                     |
 233                 GPIO_LED_A                      |
 234                 GPIO_LED_B                      |
 235                 GPIO_LED_C                      |
 236                 GPIO_LED_D                      |
 237                 GPIO_FPGA_DIN           |
 238                 GPIO_FPGA_DOUT          |
 239                 GPIO_FPGA_CCLK          |
 240                 GPIO_FPGA_NINIT         |
 241                 GPIO_FPGA_NPROGRAM      |
 242                 GPIO_FPGA_DONE          |
 243                 GPIO_MUXSEL_HIPKD       |
 244                 GPIO_MUXSEL_HIRAW       |
 245                 GPIO_MUXSEL_LOPKD       |
 246                 GPIO_MUXSEL_LORAW       |
 247                 GPIO_RELAY                      |
 248                 GPIO_NVDD_ON;
 249                 // (and add GPIO_FPGA_ON)
 250         // These pins are outputs
 251     AT91C_BASE_PIOA->PIO_OER =
 252         GPIO_LED_A                      |
 253                 GPIO_LED_B                      |
 254                 GPIO_LED_C                      |
 255                 GPIO_LED_D                      |
 256                 GPIO_RELAY                      |
 257                 GPIO_NVDD_ON;
 258         // PIO controls the following pins
 259     AT91C_BASE_PIOA->PIO_PER =
 260         GPIO_USB_PU                     |
 261                 GPIO_LED_A                      |
 262                 GPIO_LED_B                      |
 263                 GPIO_LED_C                      |
 264                 GPIO_LED_D;
 265
 266 //    USB_D_PLUS_PULLUP_OFF();
 267   usb_disable();
 268     LED_D_OFF();
 269     LED_C_ON();
 270     LED_B_OFF();
 271     LED_A_OFF();
 272
 273         AT91C_BASE_EFC0->EFC_FMR =
 274                 AT91C_MC_FWS_1FWS |
 275                 MC_FLASH_MODE_MASTER_CLK_IN_MHZ(48);
 276
 277     // Initialize all system clocks
 278     ConfigClocks();
 279
 280     LED_A_ON();
 281
 282     int common_area_present = 0;
 283     switch(AT91C_BASE_RSTC->RSTC_RSR & AT91C_RSTC_RSTTYP) {
 284     case AT91C_RSTC_RSTTYP_WATCHDOG:
 285     case AT91C_RSTC_RSTTYP_SOFTWARE:
 286     case AT91C_RSTC_RSTTYP_USER:
 287             /* In these cases the common_area in RAM should be ok, retain it if it's there */
 288             if(common_area.magic == COMMON_AREA_MAGIC && common_area.version == 1) {
 289                     common_area_present = 1;
 290             }
 291             break;
 292     default: /* Otherwise, initialize it from scratch */
 293             break;
 294     }
 295
 296     if(!common_area_present){
 297             /* Common area not ok, initialize it */
 298             int i; for(i=0; i<sizeof(common_area); i++) { /* Makeshift memset, no need to drag util.c into this */
 299                     ((char*)&common_area)[i] = 0;
 300             }
 301             common_area.magic = COMMON_AREA_MAGIC;
 302             common_area.version = 1;
 303             common_area.flags.bootrom_present = 1;
 304     }
 305
 306     common_area.flags.bootrom_present = 1;
 307     if(common_area.command == COMMON_AREA_COMMAND_ENTER_FLASH_MODE) {
 308             common_area.command = COMMON_AREA_COMMAND_NONE;
 309             flash_mode(1);
 310     } else if(BUTTON_PRESS()) {
 311             flash_mode(0);
 312     } else if(_osimage_entry == 0xffffffffU) {
 313             flash_mode(1);
 314     } else {
 315             // jump to Flash address of the osimage entry point (LSBit set for thumb mode)
 316             __asm("bx %0\n" : : "r" ( ((int)&_osimage_entry) | 0x1 ) );
 317     }
 318 }