cvs.zerfleddert.de Git - proxmark3-svn/blob - fpga/lo_edge_detect.v

   1 //-----------------------------------------------------------------------------
   2 // Copyright (C) 2014 iZsh <izsh at fail0verflow.com>
   3 //
   4 // This code is licensed to you under the terms of the GNU GPL, version 2 or,
   5 // at your option, any later version. See the LICENSE.txt file for the text of
   6 // the license.
   7 //-----------------------------------------------------------------------------
   8 //
   9 // There are two modes:
  10 // - lf_ed_toggle_mode == 0: the output is set low (resp. high) when a low
  11 //   (resp. high) edge/peak is detected, with hysteresis
  12 // - lf_ed_toggle_mode == 1: the output is toggling whenever an edge/peak
  13 //   is detected.
  14 //   That way you can detect two consecutive edges/peaks at the same level (L/H)
  15 //
  16 // Output:
  17 // - ssp_frame (wired to TIOA1 on the arm) for the edge detection/state
  18 // - ssp_clk: cross_lo
  19 `include "lp20khz_1MSa_iir_filter.v"
  20 `include "lf_edge_detect.v"
  21
  22 module lo_edge_detect(
  23     input pck0, input pck_divclk,
  24     output pwr_lo, output pwr_hi,
  25     output pwr_oe1, output pwr_oe2, output pwr_oe3, output pwr_oe4,
  26     input [7:0] adc_d, output adc_clk,
  27     output ssp_frame, input ssp_dout, output ssp_clk,
  28     input cross_lo,
  29     output dbg,
  30     input lf_field,
  31     input lf_ed_toggle_mode, input [7:0] lf_ed_threshold
  32 );
  33
  34 wire tag_modulation = ssp_dout & !lf_field;
  35 wire reader_modulation = !ssp_dout & lf_field & pck_divclk;
  36
  37 // No logic, straight through.
  38 assign pwr_oe1 = 1'b0;                                          // not used in LF mode
  39 assign pwr_oe3 = 1'b0;                                          // base antenna load = 33 Ohms
  40 // when modulating, add another 33 Ohms and 10k Ohms in parallel:
  41 assign pwr_oe2 = tag_modulation;
  42 assign pwr_oe4 = tag_modulation;
  43
  44 assign ssp_clk = cross_lo;
  45 assign pwr_lo = reader_modulation;
  46 assign pwr_hi = 1'b0;
  47
  48 // filter the ADC values
  49 wire data_rdy;
  50 wire [7:0] adc_filtered;
  51 assign adc_clk = pck0;
  52 lp20khz_1MSa_iir_filter adc_filter(pck0, adc_d, data_rdy, adc_filtered);
  53
  54 // detect edges
  55 wire [7:0] high_threshold, highz_threshold, lowz_threshold, low_threshold;
  56 wire [7:0] max, min;
  57 wire edge_state, edge_toggle;
  58 lf_edge_detect lf_ed(pck0, adc_filtered, lf_ed_threshold,
  59         max, min,
  60         high_threshold, highz_threshold, lowz_threshold, low_threshold,
  61         edge_state, edge_toggle);
  62
  63 assign dbg = lf_ed_toggle_mode ? edge_toggle : edge_state;
  64
  65 assign ssp_frame = lf_ed_toggle_mode ? edge_toggle : edge_state;
  66
  67 endmodule
  68