cvs.zerfleddert.de Git - proxmark3-svn/blob - bootrom/bootrom.c

   1 //-----------------------------------------------------------------------------
   2 // This code is licensed to you under the terms of the GNU GPL, version 2 or,
   3 // at your option, any later version. See the LICENSE.txt file for the text of
   4 // the license.
   5 //-----------------------------------------------------------------------------
   6 // Main code for the bootloader
   7 //-----------------------------------------------------------------------------
   8
   9 #include <proxmark3.h>
  10 #include "usb_cdc.h"
  11 #include "cmd.h"
  12 //#include "usb_hid.h"
  13
  14 void DbpString(char *str) {
  15   byte_t len = 0;
  16   while (str[len] != 0x00) {
  17     len++;
  18   }
  19   cmd_send(CMD_DEBUG_PRINT_STRING,len,0,0,(byte_t*)str,len);
  20 }
  21
  22 struct common_area common_area __attribute__((section(".commonarea")));
  23 unsigned int start_addr, end_addr, bootrom_unlocked;
  24 extern char _bootrom_start, _bootrom_end, _flash_start, _flash_end;
  25
  26 static void ConfigClocks(void)
  27 {
  28     // we are using a 16 MHz crystal as the basis for everything
  29     // slow clock runs at 32Khz typical regardless of crystal
  30
  31     // enable system clock and USB clock
  32     AT91C_BASE_PMC->PMC_SCER = AT91C_PMC_PCK | AT91C_PMC_UDP;
  33
  34         // enable the clock to the following peripherals
  35     AT91C_BASE_PMC->PMC_PCER =
  36                 (1<<AT91C_ID_PIOA)      |
  37                 (1<<AT91C_ID_ADC)       |
  38                 (1<<AT91C_ID_SPI)       |
  39                 (1<<AT91C_ID_SSC)       |
  40                 (1<<AT91C_ID_PWMC)      |
  41                 (1<<AT91C_ID_UDP);
  42
  43         // worst case scenario, with MAINCK = 16Mhz xtal, startup delay is 1.4ms
  44         // if SLCK slow clock runs at its worst case (max) frequency of 42khz
  45         // max startup delay = (1.4ms*42k)/8 = 7.356 so round up to 8
  46
  47         // enable main oscillator and set startup delay
  48     AT91C_BASE_PMC->PMC_MOR =
  49         AT91C_CKGR_MOSCEN |
  50         PMC_MAIN_OSC_STARTUP_DELAY(8);
  51
  52         // wait for main oscillator to stabilize
  53         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MOSCS) )
  54                 ;
  55
  56     // PLL output clock frequency in range  80 - 160 MHz needs CKGR_PLL = 00
  57     // PLL output clock frequency in range 150 - 180 MHz needs CKGR_PLL = 10
  58     // PLL output is MAINCK * multiplier / divisor = 16Mhz * 12 / 2 = 96Mhz
  59     AT91C_BASE_PMC->PMC_PLLR =
  60         PMC_PLL_DIVISOR(2) |
  61                 PMC_PLL_COUNT_BEFORE_LOCK(0x50) |
  62                 PMC_PLL_FREQUENCY_RANGE(0) |
  63                 PMC_PLL_MULTIPLIER(12) |
  64                 PMC_PLL_USB_DIVISOR(1);
  65
  66         // wait for PLL to lock
  67         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_LOCK) )
  68                 ;
  69
  70         // we want a master clock (MCK) to be PLL clock / 2 = 96Mhz / 2 = 48Mhz
  71         // datasheet recommends that this register is programmed in two operations
  72         // when changing to PLL, program the prescaler first then the source
  73     AT91C_BASE_PMC->PMC_MCKR = AT91C_PMC_PRES_CLK_2;
  74
  75         // wait for main clock ready signal
  76         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY) )
  77                 ;
  78
  79         // set the source to PLL
  80     AT91C_BASE_PMC->PMC_MCKR = AT91C_PMC_PRES_CLK_2 | AT91C_PMC_CSS_PLL_CLK;
  81
  82         // wait for main clock ready signal
  83         while ( !(AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MCKRDY) )
  84                 ;
  85 }
  86
  87 static void Fatal(void)
  88 {
  89   for(;;);
  90 }
  91
  92 void UsbPacketReceived(uint8_t *packet, int len) {
  93   int i, dont_ack=0;
  94   UsbCommand* c = (UsbCommand *)packet;
  95   volatile uint32_t *p;
  96
  97   if(len != sizeof(UsbCommand)) {
  98     Fatal();
  99   }
 100
 101   uint32_t arg0 = (uint32_t)c->arg[0];
 102
 103   switch(c->cmd) {
 104     case CMD_DEVICE_INFO: {
 105       dont_ack = 1;
 106 //      c->cmd = CMD_DEVICE_INFO;
 107       arg0 = DEVICE_INFO_FLAG_BOOTROM_PRESENT | DEVICE_INFO_FLAG_CURRENT_MODE_BOOTROM |
 108       DEVICE_INFO_FLAG_UNDERSTANDS_START_FLASH;
 109       if(common_area.flags.osimage_present) {
 110         arg0 |= DEVICE_INFO_FLAG_OSIMAGE_PRESENT;
 111       }
 112 //      UsbSendPacket(packet, len);
 113       cmd_send(CMD_DEVICE_INFO,arg0,1,2,0,0);
 114     } break;
 115
 116     case CMD_SETUP_WRITE: {
 117       /* The temporary write buffer of the embedded flash controller is mapped to the
 118        * whole memory region, only the last 8 bits are decoded.
 119        */
 120       p = (volatile uint32_t *)&_flash_start;
 121       for(i = 0; i < 12; i++) {
 122         p[i+arg0] = c->d.asDwords[i];
 123       }
 124     } break;
 125
 126     case CMD_FINISH_WRITE: {
 127       uint32_t* flash_mem = (uint32_t*)(&_flash_start);
 128 //      p = (volatile uint32_t *)&_flash_start;
 129       for (size_t j=0; j<2; j++) {
 130         for(i = 0+(64*j); i < 64+(64*j); i++) {
 131           //p[i+60] = c->d.asDwords[i];
 132           flash_mem[i] = c->d.asDwords[i];
 133         }
 134
 135         uint32_t flash_address = arg0 + (0x100*j);
 136
 137         /* Check that the address that we are supposed to write to is within our allowed region */
 138         if( ((flash_address+AT91C_IFLASH_PAGE_SIZE-1) >= end_addr) || (flash_address < start_addr) ) {
 139           /* Disallow write */
 140           dont_ack = 1;
 141           //        c->cmd = CMD_NACK;
 142           //        UsbSendPacket(packet, len);
 143           cmd_send(CMD_NACK,0,0,0,0,0);
 144         } else {
 145           uint32_t page_n = (flash_address - ((uint32_t)flash_mem)) / AT91C_IFLASH_PAGE_SIZE;
 146           /* Translate address to flash page and do flash, update here for the 512k part */
 147           AT91C_BASE_EFC0->EFC_FCR = MC_FLASH_COMMAND_KEY |
 148           MC_FLASH_COMMAND_PAGEN(page_n) |
 149           AT91C_MC_FCMD_START_PROG;
 150           //        arg0 = (address - ((uint32_t)flash_s));
 151         }
 152
 153         // Wait until flashing of page finishes
 154         uint32_t sr;
 155         while(!((sr = AT91C_BASE_EFC0->EFC_FSR) & AT91C_MC_FRDY));
 156         if(sr & (AT91C_MC_LOCKE | AT91C_MC_PROGE)) {
 157           dont_ack = 1;
 158           //        c->cmd = CMD_NACK;
 159           cmd_send(CMD_NACK,0,0,0,0,0);
 160           //        UsbSendPacket(packet, len);
 161         }
 162       }
 163     } break;
 164
 165     case CMD_HARDWARE_RESET: {
 166 //      USB_D_PLUS_PULLUP_OFF();
 167       usb_disable();
 168       AT91C_BASE_RSTC->RSTC_RCR = RST_CONTROL_KEY | AT91C_RSTC_PROCRST;
 169     } break;
 170
 171     case CMD_START_FLASH: {
 172       if(c->arg[2] == START_FLASH_MAGIC) bootrom_unlocked = 1;
 173       else bootrom_unlocked = 0;
 174       {
 175         int prot_start = (int)&_bootrom_start;
 176         int prot_end = (int)&_bootrom_end;
 177         int allow_start = (int)&_flash_start;
 178         int allow_end = (int)&_flash_end;
 179         int cmd_start = c->arg[0];
 180         int cmd_end = c->arg[1];
 181
 182         /* Only allow command if the bootrom is unlocked, or the parameters are outside of the protected
 183          * bootrom area. In any case they must be within the flash area.
 184          */
 185         if( (bootrom_unlocked || ((cmd_start >= prot_end) || (cmd_end < prot_start)))
 186            && (cmd_start >= allow_start) && (cmd_end <= allow_end) ) {
 187           start_addr = cmd_start;
 188           end_addr = cmd_end;
 189         } else {
 190           start_addr = end_addr = 0;
 191           dont_ack = 1;
 192 //          c->cmd = CMD_NACK;
 193 //          UsbSendPacket(packet, len);
 194           cmd_send(CMD_NACK,0,0,0,0,0);
 195         }
 196       }
 197     } break;
 198
 199     default: {
 200       Fatal();
 201     } break;
 202   }
 203
 204   if(!dont_ack) {
 205 //    c->cmd = CMD_ACK;
 206 //    UsbSendPacket(packet, len);
 207     cmd_send(CMD_ACK,arg0,0,0,0,0);
 208   }
 209 }
 210
 211 static void flash_mode(int externally_entered)
 212 {
 213         start_addr = 0;
 214         end_addr = 0;
 215         bootrom_unlocked = 0;
 216   byte_t rx[sizeof(UsbCommand)];
 217         size_t rx_len;
 218
 219   usb_enable();
 220   for (volatile size_t i=0; i<0x100000; i++);
 221
 222 //      UsbStart();
 223         for(;;) {
 224                 WDT_HIT();
 225
 226     if (usb_poll()) {
 227       rx_len = usb_read(rx,sizeof(UsbCommand));
 228       if (rx_len) {
 229 //        DbpString("starting to flash");
 230         UsbPacketReceived(rx,rx_len);
 231       }
 232     }
 233
 234 //              UsbPoll(TRUE);
 235
 236                 if(!externally_entered && !BUTTON_PRESS()) {
 237                         /* Perform a reset to leave flash mode */
 238 //                      USB_D_PLUS_PULLUP_OFF();
 239       usb_disable();
 240                         LED_B_ON();
 241                         AT91C_BASE_RSTC->RSTC_RCR = RST_CONTROL_KEY | AT91C_RSTC_PROCRST;
 242                         for(;;);
 243                 }
 244                 if(externally_entered && BUTTON_PRESS()) {
 245                         /* Let the user's button press override the automatic leave */
 246                         externally_entered = 0;
 247                 }
 248         }
 249 }
 250
 251 extern uint32_t _osimage_entry;
 252 void BootROM(void)
 253 {
 254     //------------
 255     // First set up all the I/O pins; GPIOs configured directly, other ones
 256     // just need to be assigned to the appropriate peripheral.
 257
 258     // Kill all the pullups, especially the one on USB D+; leave them for
 259     // the unused pins, though.
 260     AT91C_BASE_PIOA->PIO_PPUDR =
 261         GPIO_USB_PU                     |
 262                 GPIO_LED_A                      |
 263                 GPIO_LED_B                      |
 264                 GPIO_LED_C                      |
 265                 GPIO_LED_D                      |
 266                 GPIO_FPGA_DIN           |
 267                 GPIO_FPGA_DOUT          |
 268                 GPIO_FPGA_CCLK          |
 269                 GPIO_FPGA_NINIT         |
 270                 GPIO_FPGA_NPROGRAM      |
 271                 GPIO_FPGA_DONE          |
 272                 GPIO_MUXSEL_HIPKD       |
 273                 GPIO_MUXSEL_HIRAW       |
 274                 GPIO_MUXSEL_LOPKD       |
 275                 GPIO_MUXSEL_LORAW       |
 276                 GPIO_RELAY                      |
 277                 GPIO_NVDD_ON;
 278                 // (and add GPIO_FPGA_ON)
 279         // These pins are outputs
 280     AT91C_BASE_PIOA->PIO_OER =
 281         GPIO_LED_A                      |
 282                 GPIO_LED_B                      |
 283                 GPIO_LED_C                      |
 284                 GPIO_LED_D                      |
 285                 GPIO_RELAY                      |
 286                 GPIO_NVDD_ON;
 287         // PIO controls the following pins
 288     AT91C_BASE_PIOA->PIO_PER =
 289         GPIO_USB_PU                     |
 290                 GPIO_LED_A                      |
 291                 GPIO_LED_B                      |
 292                 GPIO_LED_C                      |
 293                 GPIO_LED_D;
 294
 295 //    USB_D_PLUS_PULLUP_OFF();
 296   usb_disable();
 297     LED_D_OFF();
 298     LED_C_ON();
 299     LED_B_OFF();
 300     LED_A_OFF();
 301
 302         AT91C_BASE_EFC0->EFC_FMR =
 303                 AT91C_MC_FWS_1FWS |
 304                 MC_FLASH_MODE_MASTER_CLK_IN_MHZ(48);
 305
 306     // Initialize all system clocks
 307     ConfigClocks();
 308
 309     LED_A_ON();
 310
 311     int common_area_present = 0;
 312     switch(AT91C_BASE_RSTC->RSTC_RSR & AT91C_RSTC_RSTTYP) {
 313     case AT91C_RSTC_RSTTYP_WATCHDOG:
 314     case AT91C_RSTC_RSTTYP_SOFTWARE:
 315     case AT91C_RSTC_RSTTYP_USER:
 316             /* In these cases the common_area in RAM should be ok, retain it if it's there */
 317             if(common_area.magic == COMMON_AREA_MAGIC && common_area.version == 1) {
 318                     common_area_present = 1;
 319             }
 320             break;
 321     default: /* Otherwise, initialize it from scratch */
 322             break;
 323     }
 324
 325     if(!common_area_present){
 326             /* Common area not ok, initialize it */
 327             int i; for(i=0; i<sizeof(common_area); i++) { /* Makeshift memset, no need to drag util.c into this */
 328                     ((char*)&common_area)[i] = 0;
 329             }
 330             common_area.magic = COMMON_AREA_MAGIC;
 331             common_area.version = 1;
 332             common_area.flags.bootrom_present = 1;
 333     }
 334
 335     common_area.flags.bootrom_present = 1;
 336     if(common_area.command == COMMON_AREA_COMMAND_ENTER_FLASH_MODE) {
 337             common_area.command = COMMON_AREA_COMMAND_NONE;
 338             flash_mode(1);
 339     } else if(BUTTON_PRESS()) {
 340             flash_mode(0);
 341     } else if(_osimage_entry == 0xffffffffU) {
 342             flash_mode(1);
 343     } else {
 344             // jump to Flash address of the osimage entry point (LSBit set for thumb mode)
 345             __asm("bx %0\n" : : "r" ( ((int)&_osimage_entry) | 0x1 ) );
 346     }
 347 }