// the license.
//-----------------------------------------------------------------------------
// Miscellaneous routines for low frequency tag operations.
-// Tags supported here so far are Texas Instruments (TI), HID
+// Tags supported here so far are Texas Instruments (TI), HID, EM4x05, EM410x
// Also routines for raw mode reading/simulating of LF waveform
//-----------------------------------------------------------------------------
*/
void ModThenAcquireRawAdcSamples125k(uint32_t delay_off, uint32_t period_0, uint32_t period_1, uint8_t *command)
{
-
+ // start timer
StartTicks();
- int divisor_used = 95; // 125 KHz
- // see if 'h' was specified
-
- if (command[strlen((char *) command) - 1] == 'h')
- divisor_used = 88; // 134.8 KHz
- sample_config sc = { 0,0,1, divisor_used, 0};
- setSamplingConfig(&sc);
- //clear read buffer
+ // use lf config settings
+ sample_config *sc = getSamplingConfig();
+ // clear read buffer
BigBuf_Clear_keep_EM();
/* Make sure the tag is reset */
FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
WaitMS(2500);
- //power on
- LFSetupFPGAForADC(sc.divisor, 1);
+ // power on
+ LFSetupFPGAForADC(sc->divisor, 1);
// And a little more time for the tag to fully power up
WaitMS(2000);
// now modulate the reader field
if (bitbang) {
- //HACK it appears my loop and if statements take up about 7 us so adjust waits accordingly...
+ // HACK it appears the loop and if statements take up about 7us so adjust waits accordingly...
uint8_t hack_cnt = 7;
if (period_0 < hack_cnt || period_1 < hack_cnt) {
- DbpString("Warning periods cannot be less than 7 in bit bang mode");
+ DbpString("Warning periods cannot be less than 7us in bit bang mode");
FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
LED_D_OFF();
return;
}
- //prime cmd_len to save time comparing strings while modulating
+
+ // hack2 needed--- it appears to take about 8-16us to turn the antenna back on
+ // leading to ~ 1 to 2 125khz samples extra in every off period
+ // so we should test for last 0 before next 1 and reduce period_0 by this extra amount...
+ // but is this time different for every antenna or other hw builds??? more testing needed
+
+ // prime cmd_len to save time comparing strings while modulating
int cmd_len = 0;
while(command[cmd_len] != '\0' && command[cmd_len] != ' ')
cmd_len++;
int counter = 0;
bool off = false;
for (counter = 0; counter < cmd_len; counter++) {
- //while(*command != '\0' && *command != ' ') {
// if cmd = 0 then turn field off
if (command[counter] == '0') {
// if field already off leave alone (affects timing otherwise)
LED_D_OFF();
off = true;
}
- // note we appear to take about 6us to switch over (or run the if statements/loop...)
+ // note we appear to take about 7us to switch over (or run the if statements/loop...)
WaitUS(period_0-hack_cnt);
// else if cmd = 1 then turn field on
} else {
// if field already on leave alone (affects timing otherwise)
if (off) {
- FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
+ FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
LED_D_ON();
off = false;
}
- // note we appear to take about 6us to switch over (or run the if statements/loop...)
+ // note we appear to take about 7us to switch over (or run the if statements/loop...)
WaitUS(period_1-hack_cnt);
}
}
FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
LED_D_OFF();
WaitUS(delay_off);
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor);
+ FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc->divisor);
FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
LED_D_ON();
if(*(command++) == '0') {
FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
LED_D_OFF();
WaitUS(delay_off);
- FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor);
+ FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc->divisor);
}
FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
// now do the read
DoAcquisition_config(false, 0);
- // note leaves field on... (for future commands?)
+
+ // Turn off antenna
+ FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+ // tell client we are done
+ cmd_send(CMD_ACK,0,0,0,0,0);
}
/* blank r/w tag data stream
int usage_lf_cmdread(void)
{
- PrintAndLog("Usage: lf cmdread d <delay period> z <zero period> o <one period> c <cmdbytes> [H] ");
+ PrintAndLog("Usage: lf cmdread d <delay period> z <zero period> o <one period> c <cmdbytes> ");
PrintAndLog("Options: ");
PrintAndLog(" h This help");
- PrintAndLog(" L Low frequency (125 KHz)");
- PrintAndLog(" H High frequency (134 KHz)");
- PrintAndLog(" d <delay> delay OFF period");
- PrintAndLog(" z <zero> time period ZERO");
- PrintAndLog(" o <one> time period ONE");
+ PrintAndLog(" d <delay> delay OFF period between bits (0 for bitbang mode)");
+ PrintAndLog(" z <zero> time period ZERO (antenna off in bitbang mode)");
+ PrintAndLog(" o <one> time period ONE (antenna on in bitbang mode)");
PrintAndLog(" c <cmd> Command bytes");
PrintAndLog(" ************* All periods in microseconds");
+ PrintAndLog(" ************* Use lf config to configure options.");
PrintAndLog("Examples:");
PrintAndLog(" lf cmdread d 80 z 100 o 200 c 11000");
- PrintAndLog(" lf cmdread d 80 z 100 o 100 c 11000 H");
+ PrintAndLog(" lf cmdread d 80 z 100 o 100 c 11000");
return 0;
}
/* send a command before reading */
int CmdLFCommandRead(const char *Cmd)
{
- static char dummy[3] = {0x20,0x00,0x00};
UsbCommand c = {CMD_MOD_THEN_ACQUIRE_RAW_ADC_SAMPLES_125K};
bool errors = false;
//uint8_t divisor = 95; //125khz
{
case 'h':
return usage_lf_cmdread();
- case 'H':
- //divisor = 88;
- dummy[1]='h';
- cmdp++;
- break;
- case 'L':
- cmdp++;
- break;
case 'c':
param_getstr(Cmd, cmdp+1, (char *)&c.d.asBytes, sizeof(c.d.asBytes));
cmdp+=2;
//Validations
if(errors) return usage_lf_cmdread();
- // in case they specified 'H'
- strcpy((char *)&c.d.asBytes + strlen((char *)c.d.asBytes), dummy);
-
clearCommandBuffer();
SendCommand(&c);
+
+ WaitForResponse(CMD_ACK,NULL);
+ getSamples(0, true);
+
+
return 0;
}
projects / proxmark3-svn / commitdiff