cvs.zerfleddert.de Git - rsbs2/blob - rsbs2.pl

   1 #!/usr/bin/perl -w
   2
   3 use LWP::UserAgent;
   4 use LWP::ConnCache;
   5 use XML::Simple;
   6 use Data::Dumper;
   7 use MIME::Base64;
   8 use Digest::MD5 qw(md5);
   9
  10 my $ua = LWP::UserAgent->new(cookie_jar => {});
  11 my $url;
  12 my $poweronms=200;
  13 my $poweroffms=5000;
  14 my $verbose = 0;
  15
  16 my @fw_vars = qw(ENABLE_LAN_AUTONEG ENABLE_LAN_100 ENABLE_LAN_FDUPLEX GATEWAY
  17         IP_ADDRESS NETMASK TFTP_FIRMWARE_FILE TFTP_ADDR_FIRMWARE ENABLE_DHCP
  18         ENABLE_DNS DNS_SERVER DNS_DOMAIN_NAME
  19         ACCESS_CONTROL_SERVER_1 ACCESS_CONTROL_SERVER_2 ACCESS_CONTROL_SERVERS
  20         ACPI_DISABLE_BIOS_SCAN ACPI_FORCE_RSDP_ADDRESS ACPI_FORCE_RSDT_ADDRESS
  21         ACPI_RSDP_BIOS_ROM_ADDRESS ACPI_SCAN_DELAY_SECONDS AMR_AUTH_METHOD
  22         AMR_DISABLE_PCI AMR_ENABLE_ISCSI_TIMEOUT AMR_ENABLED AMR_HOST_INTERFACE
  23         AMR_SERVER_LIST AMR_USB_FDD_CBI_UFI_TRANSPORT AMR_USB_R2T_TIMEOUT_MSEC
  24         AVR_4BIT_ACTION AVR_4BIT_SAMPLE_TIME AVR_ARCHITECTURE AVR_CHIP_TYPE
  25         AVR_CLIENT_LANGUAGE AVR_DISABLE_SVR_MOUSE_ON_SESSION_START
  26         AVR_KB_VERSION AVR_MAX_SESSION_COUNT AVR_MOUSE_ACCELERATION
  27         AVR_MOUSE_MAX_STEP_SIZE AVR_NUMB_MOUSE_PACKETS
  28         AVR_PCI_PATTERN_HANDS_OFF_ENABLED AVR_PREF_KB_STICKY_KEY_MODE_ON
  29         AVR_PREF_KB_TYPING_MODE_ON AVR_PREF_KB_WARN_UNID_EV
  30         AVR_REGISTERS_BASE_ADDR AVR_RESET_PAUSE AVR_SCREEN_REFRESH
  31         AVR_SUPPORTED_CHIP AVR_TILE_TIMEOUT AVR_VIDEO_MEM_BASE_ADDR BAUDRATE
  32         BAUDRATE_MODEM BAUDRATE_PPP BMC_SUPPORTS_GRACEFULL
  33         BMC_TIMESYNC_INTERVAL CARD_NAME CONSOLE_IPMI_MOUSE_BYTE_TIME
  34         CONSOLE_KEYBOARD_ACCESS_MODE CONSOLE_MOUSE_ACCESS_MODE
  35         CONSOLE_VIDEO_PARAM_MODE CONTACT CONTACT_PHONE CRIT_TEMP_SHUTDOWN
  36         CRIT_VOLT_SHUTDOWN DHCP_ADD_EXTENSION DHCP_ADD_SERIAL
  37         DHCP_CONFIGURE_DNS DHCP_HOSTNAME_EXT DHCP_SERVER DHCP_USE_CARDNAME
  38         DIAG_URL ENABLE_ANON_IPMI ENABLE_ANON_PCI
  39         ENABLE_ANON_WEB ENABLE_AVR_CHIP_DETECT ENABLE_BMC_AUTODETECT
  40         ENABLE_BMC_TIMESYNC ENABLE_CRTC_FETCH ENABLE_DHCP ENABLE_DHCP_HOSTNAME
  41         ENABLE_DS_CONNECTIVITY ENABLE_IO_UART_DECODER ENABLE_LAN_100
  42         ENABLE_LAN_AUTONEG ENABLE_LAN_FDUPLEX ENABLE_MEM_UART_DECODER
  43         ENABLE_PPP ENABLE_REMOTE_FLOPPY_BOOT ENABLE_SELF_DELETE
  44         ENABLE_SERIAL_DBG ETHDRIVER_SID EXPROM_BANNER EXPROM_EBDA_COMPATIBILITY
  45         EXPROM_ENTRY EXPROM_EXIT_DELAY_SEC EXPROM_F3_DELAY_SEC
  46         EXPROM_INT13_COMPATIBILITY EXPROM_SETUP_BANNER FIRMWARE_REVISION
  47         FP_ACDC FP_AMR FP_AVR_ASR FP_AVR_GRAPHIC_CONSOLE FP_AVR_TEXT_CONSOLE
  48         FP_AVRMANCONF_4BIT_SAMPLE FP_AVRMANCONF_ACCESS_MODES FP_AVRMANCONF_CHIP
  49         FP_AVRMANCONF_MOUSE_ACCELERATION FP_AVRMANCONF_MOUSE_TYPE
  50         FP_AVRMANCONF_RESET_PAUSE FP_AVRMANCONF_SCREEN_REFRESH FP_BATTERY
  51         FP_BOARDRESET_BUTTON FP_COMREDIRECT FP_F3_PPP FP_I2C FP_ICMB FP_INSTR
  52         FP_INTERNAL_LAN FP_KEY_CONSOLE FP_LAN_SPEED
  53         FP_LAST_BOARD_POWER_WARNING_ENABLED FP_NO_BLADE_PANEL
  54         FP_NO_CARDCONF_PANEL FP_NO_DIAG_PANEL FP_NO_DSAUTHCONF_PANEL
  55         FP_NO_MANAGE_PANEL FP_NO_MEMORY_PANEL FP_NO_SENSOR_PANEL
  56         FP_NO_SERVERCONF_PANEL FP_NO_SSL_PANEL FP_NO_SYSLOG_PANEL
  57         FP_NO_USERCONF_PANEL FP_PAGING_EMAIL FP_PAGING_SERIAL FP_PAGING_SNMP
  58         FP_PCI_CONFIG FP_PPP FP_PROP_BAUDRATE_REQBOOT FP_PROP_PPP_INIT_REQBOOT
  59         FP_PROP_PS_REQBOOT FP_PROP_TERM_DIRECT_CONNECT_REQBOOT FP_REMOTE_BOOT
  60         FP_REMOTE_DISK FP_REMOTE_POWER FP_SAC_CONSOLE FP_SEL FP_SENSOR_HISTORY
  61         FP_SEQ_SEL FP_SERVER_POWER FP_SERVER_REBOOT FP_SERVER_RESET
  62         FP_SERVER_SHUTDOWN FP_SMM FP_SSL FP_STATUS_DIAG_PANEL
  63         FP_STATUS_MEMORY_PANEL FP_STATUS_PCI_CONFIG FP_STATUS_SAC_CONSOLE
  64         FP_SYSTEM_LAN FP_TEXT_ASR FP_TEXT_CONSOLE FP_TUI FP_VERSION FP_VGA_ASR
  65         FP_VGA_CONSOLE FP_VT100_CONSOLE GATEWAY GATEWAY_MAC
  66         GRATUITOUS_ARP_INTERVAL HELP_LOCATION HIST0_SAMPLE_TIME HIST0_SENSOR_ID
  67         HIST1_SAMPLE_TIME HIST1_SENSOR_ID HIST2_SAMPLE_TIME HIST2_SENSOR_ID
  68         HIST3_SAMPLE_TIME HIST3_SENSOR_ID HTTP_PORT_NUM HTTP_SSL_PORT_NUM
  69         I2C_ADDR_8BIT_CHASSIS_BMC I2C_ADDR_8BIT_MY_BMC I2C_ADDR_8BIT_THIS_CARD
  70         INFOTXT_BPROP_ACCESS INFOTXT_DB_ACCESS IP_ADDRESS IP_ADDRESS_SOURCE
  71         IPMB_RETRY_TIMEOUT IPMB_SEQ_NUM_TIMEOUT IPMB_TX_RETRIES
  72         IPMI_COUNTRY_SELECT IPV4_HEADER_PARAMETERS ISCSI_DEVICE_VENDOR
  73         ISCSI_PRODUCT_EMUL_BD ISCSI_PRODUCT_EMUL_CD ISCSI_PRODUCT_EMUL_FD
  74         LAST_CARD_NAME LAST_ENABLE_DHCP LAST_GATEWAY LAST_IP_ADDRESS
  75         LAST_NETMASK LOCATION MAC_ADDRESS MODEM_CONNECT MODEM_CONNECT2
  76         MODEM_SEPARATOR NETMASK PAGE_RETRIES PAGE_RETRY_DELAY_SEC POST_ERRCODE
  77         POST_PROP PPP_AVAILABLE PPP_INIT PPP_IP_ADDR PPP_NETMASK PPP_PORT
  78         PPP_STATUS PPP_STAY_ALIVE_SECS PPP_WELCOME PPP2_BAUDRATE PPP2_INIT
  79         PPP2_IP_ADDR PPP2_NETMASK PPP2_PORT PPP2_STAY_ALIVE_SECS PRODUCT
  80         PRODUCT_ABBR PS_ASR PS_DISK PS_FAN PS_HARDWARE PS_MEMORY PS_NETWORK
  81         PS_OTHER PS_POST PS_RMC PS_SECURITY PS_SYS_POWER PS_SYS_STATUS
  82         PS_TEMPERATURE PS2_ADAPTER_POWER_UP_MODE PS2_FW_UPDATE_CMD
  83         PS2_FW_UPDATE_IMG_NAME PS2_FW_UPDATE_STATUS RMC_DS_GROUP SAC_PORT
  84         SERVER_CODEPAGE SERVER_HARD_RESET_PULSE_MS SERVER_HARD_RESET_VIA_IPMI
  85         SERVER_ID SERVER_IP SERVER_KEYBOARD SERVER_KEYBOARD_LANGUAGES_LIST
  86         SERVER_MEMORY SERVER_NAME SERVER_POWER_CHANGE_VIA_IPMI
  87         SERVER_POWER_OFF_MODE SERVER_POWER_OFF_PULSE_MS SERVER_POWER_ON_MODE
  88         SERVER_POWER_ON_PULSE_MS SERVER_TIMEZONE SERVER_URL
  89         SESSION_MANAGER_SESSION_TIMEOUT SI_DEF_POLL_INTERVAL_MS
  90         SI_DEF_POLL_OFFSET_MS SMTP_RESP_TIME_SEC SMTP_RETRIES
  91         SMTP_RETRY_DELAY_SEC SMTP_REVERSE_PATH SMTP_SERVER SNMP_AGENT_ENABLED
  92         SNMP_COMMUNITY SNMP_ENTERPRISE_ID SNMP_SERVER SNMP_SERVER_1
  93         SNMP_SERVER_2 SNMP_SERVER_3 SNMP_SERVER_4 SNMP_SERVER_5 SNMP_SERVER_6
  94         SNMP_SERVER_7 SNMP_SERVER_MAC SNMP_SYSOID SNMP_TRAP_MASK
  95         SNMP_TRAP_VERSION SSL_40_OR_128_ENCRYPTION SSL_CAPABLE_FIRMWARE
  96         SSL_ENABLE_ALOG SSL_ENABLE_ALOG_FALLBACK SSL_ENABLE_CLIENT_CERT
  97         SSL_ENABLE_HTTP SSL_ENABLE_HTTPS SSL_ENABLE_NOTIFY
  98         SSL_NOTIFICATION_TIME TELNET_ENABLE TELNET_PORT_NUM
  99         TERMINAL_DIRECT_CONNECT TERMINAL_ENCODING TEXT_CONSOLE_TIMEOUT
 100         TFTP_ADDR_FIRMWARE TFTP_ADDR_REBOOT TFTP_FIRMWARE_FILE TFTP_REBOOT_FILE
 101         TXT_REMOTE_CONSOLE_COLOR_MAP TXT_REMOTE_CONSOLE_FREQ
 102         USB_DEVICE_SETTINGS USE_SERVER_IP_ADDRESS USER_TIMEOUT VENDOR
 103         RMC_AUTODETECT RMC_FUNCTIONS RMC_MODULES AGENT_VERSION BIOS_VER
 104         BOARD_MFT BOARD_MODEL BOARD_PART_NUM BOARD_SERIAL BOARD_VER CAB_MFT
 105         CAB_MODEL CAB_PROD_NUM CAB_PROD_VER CAB_SERIAL CHA_MODEL
 106         CSV_ConfAlarmMailFrom CSV_ConfAlarmMailMessage CSV_ConfAlarmMailSubject
 107         CSV_ConfAlarmMailType CSV_ConfAlarmMailUserInfo0
 108         CSV_ConfAlarmMailUserInfo1 PER_USER_PAGING RMC_SEL_FILTER
 109         SERVER_AD_NAME SERVER_AD_NAME2 SERVER_AD_NAME3 SERVER_AD_NAME4
 110         SERVER_CONTACT SERVER_DESCRIPTION SERVER_IP_ADDRESS SERVER_IP_ADDRESS2
 111         SERVER_IP_ADDRESS3 SERVER_IP_ADDRESS4 SERVER_IP_DHCP SERVER_IP_DHCP2
 112         SERVER_IP_DHCP3 SERVER_IP_DHCP4 SERVER_IP_GATEWAY SERVER_IP_GATEWAY2
 113         SERVER_IP_GATEWAY3 SERVER_IP_GATEWAY4 SERVER_IP_NETMASK
 114         SERVER_IP_NETMASK2 SERVER_IP_NETMASK3 SERVER_IP_NETMASK4
 115         SERVER_LOCATION SERVER_MAC_ADDRESS SERVER_MAC_ADDRESS2
 116         SERVER_MAC_ADDRESS3 SERVER_MAC_ADDRESS4 SERVER_MAX_LAN_ADAPTER
 117         SERVER_OS SERVER_OS_VENDOR);
 118
 119 sub _crc16 {
 120         my $str = shift;
 121         my $crc = 0;
 122         for my $k (0..length($str)-1) {
 123                 $crc ^= ord(substr($str, $k, 1)) << 8;
 124                 for (0..7) {
 125                         $crc = (($crc & 0x8000) == 32768 ? ($crc<<1) ^ 0x1021 : $crc<<1);
 126                 }
 127         }
 128         $crc = $crc & 0xFFFF;
 129         return $crc;
 130 }
 131
 132 sub _hash {
 133         my ($password, $challenge) = @_;
 134         my @challenge_bytes = unpack 'c16', decode_base64($challenge);
 135         my @pwd_hash = unpack 'c16', md5($password);
 136         my @xor_bytes;
 137         for my $i (0..15) {
 138                 $xor_bytes[$i] = $challenge_bytes[$i] ^ $pwd_hash[$i];
 139         };
 140         my $hash = md5(pack 'c16', @xor_bytes);
 141         my $crc = _crc16($hash);
 142         $hash .= chr($crc & 0xff) . chr($crc >> 8 & 0xff);
 143         return encode_base64($hash, "");
 144 }
 145
 146 sub _req {
 147         my $xml = shift;
 148         $request = HTTP::Request->new(POST => "${url}/cgi/bin");
 149         $request->content_type('application/x-www-form-urlencoded');
 150         $request->content('<?XML version="1.0"?><?RMCXML version="1.0"?><RMCSEQ>'.$xml.'</RMCSEQ>');
 151         $response = $ua->request($request);
 152         die("Error in request: " . $response->status_line . "\n") unless ($response->is_success);
 153         XMLin($response->content, SuppressEmpty => '')->{RESP};
 154 }
 155
 156 sub _cmd {
 157         my $cmd = shift;
 158
 159         my $reqstr='<REQ CMD="'.$cmd.'"></REQ>';
 160         my $res = _req($reqstr);
 161         if ($res->{RC} ne '0x0') {
 162                 print "${cmd} failed: ".$res->{RC}."\n";
 163                 undef;
 164         }
 165
 166         $res;
 167 }
 168
 169 sub _getprop {
 170         my $property = shift;
 171
 172         my $reqstr='<REQ CMD="propget"><PROPLIST><PROP NAME="'.$property.'"/></PROPLIST></REQ>';
 173         my $resp = _req($reqstr);
 174
 175         print "get: ${property}\n" if ($verbose);
 176
 177         if ($resp->{RC} ne '0x0') {
 178                 $resp->{RC};
 179         } else {
 180                 $resp;
 181         }
 182 }
 183
 184 sub logout {
 185         print "Logout\n" if ($verbose);
 186         my $request = HTTP::Request->new(GET => "${url}/cgi/logout");
 187         my $response = $ua->request($request);
 188         die("While trying to logout: " . $response->status_line . "\n") unless ($response->is_success);
 189
 190         my $xmlin = XMLin($response->decoded_content);
 191         die "Error logging out: ".$xmlin->{RC} if ($xmlin->{RC} ne '0x0');
 192 }
 193
 194 sub setprop {
 195         my $property = shift;
 196         my $value = shift;
 197
 198         my $oldval = _getprop($property)->{PROPLIST}->{PROP}->{VAL};
 199
 200         if ($value eq $oldval) {
 201                 print "${property} is already ${value}\n" if ($verbose);
 202                 return;
 203         }
 204
 205         my $reqstr='<REQ CMD="propset"><PROP NAME="'.$property.'"><VAL>'.$value.'</VAL></PROP></REQ>';
 206         my $res = _req($reqstr);
 207
 208         if ($res->{RC} ne '0x0') {
 209                 print "Error setting ${property} to ${value}: ".$res->{RC}."\n";
 210                 undef;
 211         } else {
 212                 print "${property}: ${oldval} -> ${value}\n" if ($verbose);
 213                 $oldval;
 214         }
 215 }
 216
 217 sub serveraction {
 218         my $action = shift;
 219
 220         my $pmode = 2;
 221
 222         setprop("SERVER_HARD_RESET_VIA_IPMI", "FALSE");
 223         setprop("SERVER_POWER_CHANGE_VIA_IPMI", "FALSE");
 224         #PM Mode
 225         setprop("SERVER_POWER_ON_MODE", sprintf("0x%x", $pmode));
 226         setprop("SERVER_POWER_OFF_MODE", sprintf("0x%x", $pmode));
 227
 228         print "${action}...\n" if ($verbose);
 229         my $reqstr='<REQ CMD="serveraction"><ACT>'.$action.'</ACT></REQ>';
 230         my $res = _req($reqstr);
 231
 232         if ($res->{RC} ne '0x0') {
 233                 print "FAILED:".$res->{RC}."\n";
 234         }
 235 }
 236
 237 sub powerup {
 238         print "powerup\n" if ($verbose);
 239         setprop("SERVER_POWER_ON_PULSE_MS", sprintf("0x%x", $poweronms));
 240         setprop("SERVER_POWER_OFF_PULSE_MS", "0x0");
 241         serveraction("powercycle");
 242 }
 243
 244 sub powerdown {
 245         print "powerdown\n" if ($verbose);
 246         setprop("SERVER_POWER_ON_PULSE_MS", "0x0");
 247         setprop("SERVER_POWER_OFF_PULSE_MS", sprintf("0x%x", $poweroffms));
 248         serveraction("powercycle");
 249 }
 250
 251 sub powercycle {
 252         print "powercycle\n" if ($verbose);
 253         setprop("SERVER_POWER_ON_PULSE_MS", sprintf("0x%x", $poweronms));
 254         setprop("SERVER_POWER_OFF_PULSE_MS", sprintf("0x%x", $poweroffms));
 255         serveraction("powercycle");
 256 }
 257
 258 sub showprop {
 259         my $property = shift;
 260
 261         my $phash = _getprop($property)->{PROPLIST}->{PROP};
 262
 263         print "${property}: " . ${phash}->{VAL} . " (" . ${phash}->{PERMS} . ")\n";
 264 }
 265
 266 sub board_properties {
 267         my $reqstr='<REQ CMD="boardpropget"><PROPLIST><PROP NAME=""/></PROPLIST></REQ>';
 268         my $resp = _req($reqstr);
 269
 270         print " * Board Properties:\n";
 271         foreach my $bprop (@{$resp->{BPROPLIST}->{BPROP}}) {
 272                 print " * " . ${bprop}->{NAME} . ": " . ${bprop}->{VAL} . "\n";
 273         }
 274 }
 275
 276 sub show_boarddesc {
 277         my $reqstr='<REQ CMD="boardpropget"><BPROPLIST><BPROP NAME="BOARD_DESCRIPTION"/></BPROPLIST></REQ>';
 278         my $boarddesc64 = _req($reqstr)->{BPROPLIST}->{BPROP}->{VAL};
 279         my $boarddesc = decode_base64($boarddesc64);
 280         my @board = split(//, $boarddesc);
 281         foreach my $byte (@board) {
 282                 printf ("0x%02x ", ord($byte));
 283         }
 284         print "\n";
 285 }
 286
 287 sub show_all_vars {
 288         foreach my $fwvar (@fw_vars) {
 289                 showprop($fwvar);
 290         }
 291 }
 292
 293 sub usrlist {
 294         my $res = _cmd("usrlist");
 295         my @users = ();
 296
 297         if ($res->{RC} ne '0x0') {
 298                 print "FAILED:".$res->{RC}."\n";
 299                 ();
 300         } else {
 301                 if (ref($res->{USRLIST}->{USER}) eq 'ARRAY') {
 302                         foreach my $usr (@{$res->{USRLIST}->{USER}}) {
 303                                 push @users, $usr->{NAME};
 304                         }
 305                 } else {
 306                         push @users, $res->{USRLIST}->{USER}->{NAME};
 307                 }
 308         }
 309         @users;
 310 }
 311
 312 sub getusrprops {
 313         my $usr = shift;
 314
 315         my $reqstr = '<REQ CMD="usrpropget"><USER NAME="'.$usr.'"></USER></REQ>';
 316         my $res = _req($reqstr)->{USER}->{PROP};
 317
 318         $res;
 319 }
 320
 321 sub usradd {
 322         my $usr = shift;
 323
 324         my $reqstr='<REQ CMD="usradd"><USER NAME="'.$usr.'"/></REQ>';
 325         my $res = _req($reqstr);
 326         if ($res->{RC} ne '0x0') {
 327                 print "FAILED:".$res->{RC}."\n";
 328         }
 329 }
 330
 331 sub setusrprop {
 332         my $usr = shift;
 333         my $property = shift;
 334         my $value = shift;
 335
 336         my $reqstr='<REQ CMD="usrpropget"><USER NAME="'.$usr.'"><PROP NAME="'.$property.'"></PROP></USER></REQ>';
 337         my $res = _req($reqstr);
 338
 339         my $oldval = ${res}->{USER}->{PROP}->{VAL};
 340
 341         if ($value eq $oldval) {
 342                 print "${property} is already ${value}\n" if ($verbose);
 343                 return;
 344         }
 345
 346         $reqstr='<REQ CMD="usrpropset"><USER NAME="'.$usr.'"><PROP NAME="'.$property.'"><VAL>'.$value.'</VAL></PROP></USER></REQ>';
 347         $res = _req($reqstr);
 348
 349         if ($res->{RC} ne '0x0') {
 350                 print "Error setting ${property} to ${value}: ".$res->{RC}."\n";
 351                 undef;
 352         } else {
 353                 print "${property}: ${oldval} -> ${value}\n" if ($verbose);
 354                 $oldval;
 355         }
 356 }
 357
 358 sub syslog_debug {
 359         my $destination_ip = shift;
 360         my $bcast = shift;
 361
 362         my $reqstr='<REQ CMD="dbgmsglancfg"><IP>'.${destination_ip}.'</IP><BCAST>'.${bcast}.'</BCAST><STORE>FALSE</STORE></REQ>';
 363         my $res = _req($reqstr);
 364         if ($res->{RC} ne '0x0') {
 365                 print "FAILED:".$res->{RC}."\n";
 366                 return;
 367         }
 368
 369         $reqstr='<REQ CMD="dbgmsgcfg"><ON>TRUE</ON><CHANNELMASK>0x1</CHANNELMASK><MMASK>0x1</MMASK><STORE>FALSE</STORE></REQ>';
 370         $res = _req($reqstr);
 371         if ($res->{RC} ne '0x0') {
 372                 print "FAILED:".$res->{RC}."\n";
 373                 return;
 374         }
 375
 376         print "Debug messages will be sent to ${destination_ip} (broadcast: ${bcast})\n";
 377 }
 378
 379 sub get_sensors {
 380         my $slist= _cmd("sensorlist");
 381         my @sensors;
 382
 383         if ($slist->{RC} ne '0x0') {
 384                 print "Error getting sensorlist: ".$slist->{RC}."\n";
 385                 return;
 386         }
 387
 388         my $req = '<REQ CMD="sensorpropget"><HANDLE>0x1</HANDLE><SENSORLIST>';
 389         foreach my $s (@{$slist->{SENSORLIST}->{SENSOR}}) {
 390                 $req .= '<SENSOR KEY="'.$s->{KEY}.'"/>';
 391         }
 392         $req .= '</SENSORLIST></REQ>';
 393
 394         my $sprop = _req($req);
 395         foreach my $s (@{$sprop->{SENSORLIST}->{SENSOR}}) {
 396                 my $sensor = {};
 397                 foreach my $sp (@{$s->{PROP}}) {
 398                         $sensor->{$sp->{NAME}} = $sp->{VAL};
 399                 }
 400
 401                 next if (!defined($sensor->{NAME}));
 402                 $sensor->{VAL} = '0' if ($sensor->{VAL} eq '');
 403                 push @sensors, $sensor;
 404         }
 405         @sensors;
 406 }
 407
 408 sub show_sensors {
 409         my @sensors = get_sensors();
 410
 411         foreach my $sensor (@sensors) {
 412                 print $sensor->{NAME}.": ".$sensor->{VAL}.$sensor->{UNITS};
 413
 414                 my @info = ();
 415                 foreach my $field qw(MIN MAX LOW_NON_CRITICAL UPPER_NON_CRITICAL LOW_CRITICAL UPPER_CRITICAL) {
 416                         if ($sensor->{$field} ne '') {
 417                                 push @info, "${field}: ".$sensor->{$field}.$sensor->{UNITS};
 418                         }
 419                 }
 420
 421                 print "\t(".join(", ",@info).")" if (@info);
 422
 423                 print "\n";
 424         }
 425 }
 426
 427 sub status {
 428         my $boardstatus = _cmd("boardstatus")->{STATUS};
 429         my $fw = _cmd("boardfwstatus");
 430         my $boardfwstatus = $fw->{STATUS};
 431         my $boardfwprogress = $fw->{PROGRESS};
 432         $bs = hex($boardstatus);
 433
 434         print "Server Power:\t\t" . (($bs & 0x01) ? "ON" : "OFF") . "\n";
 435         print "External PSU:\t\t" . (($bs & 0x02) ? "ON" : "OFF") . "\n";
 436         print "Battery:\t\t";
 437         if ($bs & 0x04) {
 438                 if ($bs & 0x08) {
 439                         print "LOW\n";
 440                 } elsif ($bs & 0x800) {
 441                         print "ON\n";
 442                 } else {
 443                         print "UNKNOWN\n";
 444                 }
 445         } else {
 446                 print "OFF\n";
 447         }
 448         print "Standby Power:\t\t" . (($bs & 0x08) ? "ON" : "OFF") . "\n";
 449         print "LAN:\t\t\t" . (($bs & 0x10) ? "CONNECTED" : "NC") . "\n";
 450         print "I2C:\t\t\t" . (($bs & 0x20) ? "CONNECTED" : "NC") . "\n";
 451         print "SMM:\t\t\t" . (($bs & 0x40) ? "CONNECTED" : "NC") . "\n";
 452         print "Instrumentation:\t" . (($bs & 0x200) ? "CONNECTED" : "NC") . "\n";
 453         print "ICMB:\t\t\t" . (($bs & 0x400) ? "CONNECTED" : "NC") . "\n";
 454         print "PPP:\t\t\t" . (($bs & 0x10000) ? "ON" : "OFF") . "\n";
 455         print "Paging:\t\t\t" . (($bs & 0x20000) ? "ON" : "OFF") . "\n";
 456         print "COM redirection:\t" . (($bs & 0x100000) ? "ON" : "OFF") . "\n";
 457         print "UART redirect:\t\t" . (($bs & 0x200000) ? "ON" : "OFF") . "\n";
 458         print "UART redirect pending:\t" . (($bs & 0x400000) ? "TRUE" : "FALSE") . "\n";
 459         print "Hex BoardStatus:\t${boardstatus}\n";
 460         my $fws = hex ($boardfwstatus);
 461         print "FW status:\t\t";
 462         if ($fws == 3 || $fws == 32771) {
 463                 print "WAITING";
 464         } else {
 465                 print "DONE";
 466         }
 467         print " (${boardfwstatus})\n";
 468         if (($fws & 0x8080) || ($fws & 0x80)) {
 469                 printf("FW error:\t\t0x%02x\n", ($fws & 0xff));
 470         }
 471         if ($fws != 0) {
 472                 print "FW upgrade progress:\t${boardfwprogress}\n";
 473         }
 474         print "\nSensors:\n";
 475         show_sensors();
 476 }
 477
 478 sub spawn_gui {
 479         my $base = shift;
 480         open(APPLET,"|appletviewer /dev/stdin");
 481         print APPLET '<HTML><HEAD><TITLE>RSB S2 User Interface</TITLE></HEAD>';
 482         print APPLET '<BODY>';
 483         print APPLET '<object width="640" height="480">';
 484         print APPLET '<param name="code" value="com/agilent/rmc/mgui/RmcUI.class">';
 485         print APPLET '<param name="codebase" value="'.$base.'/">';
 486         print APPLET '<param name="archive" value="gui.jar, msa_shared.jar, msa_shared_comm.jar, msa_shared_oem.jar">';
 487         print APPLET '</object>';
 488         print APPLET '</BODY></HTML>';
 489         close(APPLET);
 490 }
 491
 492 sub login {
 493         my $user = shift;
 494         my $pass = shift;
 495
 496         my $response = $ua->get("${url}/cgi/challenge");
 497         die $response->status_line if (!($response->is_success));
 498
 499         my $xmlin = XMLin($response->decoded_content);
 500         die "Error getting Challenge: ".$xmlin->{RC} if ($xmlin->{RC} ne '0x0');
 501         my $challenge = $xmlin->{CHALLENGE};
 502         print "Challenge: ${challenge}\n" if ($verbose);
 503
 504         my $sid = $response->headers->header('Set-Cookie');
 505         die "No SessionID!" if (!defined($sid));
 506         chomp($sid);
 507         $sid =~ s/.*sid=(.*);.*/$1/;
 508         print "SID: ${sid}\n" if ($verbose);
 509
 510         my $login_hash = _hash($pass, $challenge);
 511         print "Hash: ${login_hash}\n" if ($verbose);
 512
 513         my $request = HTTP::Request->new(GET => "${url}/cgi/login?user=${user}&hash=${login_hash}");
 514         $response = $ua->request($request);
 515         die("While trying to login: " . $response->status_line . "\n") unless ($response->is_success);
 516
 517         $xmlin = XMLin($response->decoded_content);
 518         die "Error logging in: ".$xmlin->{RC} if ($xmlin->{RC} ne '0x0');
 519
 520         print "Logged in\n" if ($verbose);
 521 }
 522
 523 sub read_inifile {
 524         my $filename = shift;
 525
 526         open(INIFILE,"<${filename}") || die("can't open config: ${filename}: $!");
 527         my %Ini = ();
 528         my @sections = ();
 529         while(<INIFILE>) {
 530                 chomp;
 531
 532                 next if (m/^#/);
 533
 534                 if (m/^\s*\[(.*)\]\s*$/) {
 535                         push @sections, $1;
 536                         next;
 537                 }
 538
 539                 if (@sections) {
 540                         if (m/^\s*([^=]+)\s*=\s*(.*)\s*$/) {
 541                                 ${$Ini{$sections[$#sections]}}{$1} = $2;
 542                         }
 543                 }
 544         }
 545         close(INIFILE);
 546
 547         %Ini;
 548 }
 549
 550 my %Config = read_inifile("$ENV{HOME}/.rsbs2rc");
 551
 552 my $valid_arg = 0;
 553 my $powup = 0;
 554 my $powdown = 0;
 555 my $powcyc = 0;
 556 my $reset = 0;
 557 my $resetrsbs2 = 0;
 558 my @sprop = ();
 559 my @gprop = ();
 560 my @xmlsend = ();
 561 my $show = 0;
 562 my $enable_debug = "";
 563 my $save = "";
 564 my $load = "";
 565 my $showstat = 0;
 566 my $gui = 0;
 567 my $hostalias;
 568
 569 while (defined($ARGV[0])) {
 570         SWITCH: for ($ARGV[0]) {
 571                 /^-v$/  && do {
 572                                 $verbose = 1;
 573                                 shift @ARGV;
 574                                 last SWITCH;
 575                         };
 576                 /^-g$/ && do {
 577                                 shift @ARGV;
 578                                 push @gprop, shift @ARGV;
 579                                 last SWITCH;
 580                         };
 581                 /^-s$/ && do {
 582                                 shift @ARGV;
 583                                 push @sprop, shift @ARGV;
 584                                 last SWITCH;
 585                         };
 586                 /^-u$/ && do {
 587                                 $powup = 1;
 588                                 shift @ARGV;
 589                                 last SWITCH;
 590                         };
 591                 /^-d$/ && do {
 592                                 $powdown = 1;
 593                                 shift @ARGV;
 594                                 last SWITCH;
 595                         };
 596                 /^-c$/ && do {
 597                                 $powcyc = 1;
 598                                 shift @ARGV;
 599                                 last SWITCH;
 600                         };
 601                 /^-r$/ && do {
 602                                 $reset = 1;
 603                                 shift @ARGV;
 604                                 last SWITCH;
 605                         };
 606                 /^-R$/ && do {
 607                                 $resetrsbs2 = 1;
 608                                 shift @ARGV;
 609                                 last SWITCH;
 610                         };
 611                 /^-l$/ && do {
 612                                 shift @ARGV;
 613                                 $enable_debug = shift @ARGV;
 614                                 last SWITCH;
 615                         };
 616                 /^-x$/ && do {
 617                                 $show = 1;
 618                                 shift @ARGV;
 619                                 last SWITCH;
 620                         };
 621                 /^-X$/ && do {
 622                                 shift @ARGV;
 623                                 push @xmlsend, shift @ARGV;
 624                                 last SWITCH;
 625                         };
 626                 /^-b$/ && do {
 627                                 $showstat = 1;
 628                                 shift @ARGV;
 629                                 last SWITCH;
 630                         };
 631                 /^-G$/ && do {
 632                                 $gui = 1;
 633                                 shift @ARGV;
 634                                 last SWITCH;
 635                         };
 636                 /^-save$/ && do {
 637                                 shift @ARGV;
 638                                 $save = shift @ARGV;
 639                                 last SWITCH;
 640                         };
 641                 /^-load$/ && do {
 642                                 shift @ARGV;
 643                                 $load = shift @ARGV;
 644                                 last SWITCH;
 645                         };
 646
 647                 if (defined($ARGV[0])) {
 648                         $hostalias = $ARGV[0];
 649                         shift(@ARGV);
 650                         $valid_arg = 1;
 651                 }
 652
 653                 while ( defined($ARGV[0]) ) { $valid_arg = 0; shift(@ARGV); }
 654         }
 655 }
 656
 657 if ($valid_arg && (!defined($Config{$hostalias}))) {
 658         $valid_arg = 0;
 659 }
 660
 661 if (!$valid_arg) {
 662         print STDERR "Usage: $0 options card-alias\n";
 663         print STDERR "Options:\n";
 664         print STDERR "\t-g property\tget property value\n";
 665         print STDERR "\t-s property=val\tset property value\n";
 666         print STDERR "\t-u\t\tpowerup\n";
 667         print STDERR "\t-d\t\tpowerdown\n";
 668         print STDERR "\t-c\t\tpowercycle\n";
 669         print STDERR "\t-r\t\treset\n";
 670         print STDERR "\t-R\t\treset RSB S2 board\n";
 671         print STDERR "\t-x\t\tshow all properties, variables and settings\n";
 672         print STDERR "\t-l IP\t\tsend SYSLOG debug messages to IP\n";
 673         print STDERR "\t-b\t\tshow board/server status\n";
 674         print STDERR "\t-X\t\tsend raw XML string (start with REQ tag)\n";
 675         print STDERR "\t-G\t\tstart GUI in appletviewer\n";
 676         print STDERR "\t-v\t\tverbose\n";
 677         print STDERR "\t-save file\tsave configuration to 'file'\n";
 678         print STDERR "\t-load file\tload configuration from 'file'\n";
 679         print STDERR "\n";
 680         print STDERR "card-alias\tone of: ";
 681         foreach my $alias (keys(%Config)) {
 682                 print STDERR "\"${alias}\" ";
 683         }
 684         print STDERR "(see ~/.rsbs2rc)\n";
 685         exit(1);
 686 }
 687
 688 my $host = ${$Config{$hostalias}}{"host"};
 689 $poweronms = ${$Config{$hostalias}}{"poweronms"} if (defined(${$Config{$hostalias}}{"poweronms"}));
 690 $poweroffms = ${$Config{$hostalias}}{"poweroffms"} if (defined(${$Config{$hostalias}}{"poweroffms"}));
 691
 692 my $ssl = ${$Config{$hostalias}}{"ssl"};
 693 my $port = ${$Config{$hostalias}}{"port"};
 694
 695 if (defined($ssl) && (lc($ssl) eq 'yes')) {
 696         $ENV{HTTPS_DEBUG} = 1;
 697         $ENV{HTTPS_VERSION} = 3;
 698         $port = 443 if (!defined($port));
 699         $url = "https://${host}:${port}";
 700 } else {
 701         $port = 80 if (!defined($port));
 702         $url = "http://${host}:${port}";
 703 }
 704
 705 if ($gui) {
 706         spawn_gui($url);
 707 }
 708
 709 login(${$Config{$hostalias}}{"user"}, ${$Config{$hostalias}}{"pass"});
 710
 711 if ($show) {
 712         show_boarddesc();
 713         board_properties();
 714         show_all_vars();
 715 }
 716
 717 if (@gprop) {
 718         foreach my $p (@gprop) {
 719                 showprop($p);
 720         }
 721 }
 722
 723 if (@sprop) {
 724         foreach my $p (@sprop) {
 725                 (my $pr, $v) = split(/=/,$p,2);
 726                 my $oldval = setprop($pr, $v);
 727                 if (defined($oldval)) {
 728                         print "${pr}: ${oldval} -> ${v}\n" if (!$verbose);
 729                 }
 730         }
 731 }
 732
 733 if (@xmlsend) {
 734         foreach my $x (@xmlsend) {
 735                 $Data::Dumper::Terse = 1;
 736                 print Dumper(_req($x));
 737         }
 738 }
 739
 740 if ($save ne '') {
 741         my @dontsave = qw(ENABLE_LAN_AUTONEG ENABLE_LAN_100 ENABLE_LAN_FDUPLEX
 742         GATEWAY IP_ADDRESS NETMASK TFTP_FIRMWARE_FILE TFTP_ADDR_FIRMWARE
 743         ENABLE_DHCP MAC_ADDRESS LAST_CARD_NAME LAST_ENABLE_DHCP LAST_GATEWAY
 744         LAST_IP_ADDRESS LAST_NETMASK);
 745
 746         open (SAVEFILE, ">${save}") || die "Error opening save-file: $!\n";
 747         print SAVEFILE "[global]\n";
 748         print STDERR "saving" if (!$verbose);
 749         foreach my $ts (@fw_vars) {
 750                 next if (grep(/^${ts}$/, @dontsave));
 751
 752                 my $phash = _getprop($ts)->{PROPLIST}->{PROP};
 753                 next if ($phash->{PERMS} ne 'RW');
 754
 755                 print SAVEFILE "${ts}=".$phash->{VAL}."\n";
 756                 print STDERR "." if (!$verbose);
 757         }
 758         foreach my $usr (usrlist()) {
 759                 print SAVEFILE "\n[${usr}]\n";
 760                 foreach my $up (@{getusrprops($usr)}) {
 761                         next if ($up->{PERMS} ne 'RW');
 762
 763                         print SAVEFILE $up->{NAME}."=".$up->{VAL}."\n";
 764                 }
 765                 print STDERR "." if (!$verbose);
 766         }
 767         close(SAVEFILE);
 768         print STDERR "done\n" if (!$verbose);
 769 }
 770
 771 if ($load ne '') {
 772         my %loadfile = read_inifile("${load}");
 773         print STDERR "loading" if (!$verbose);
 774
 775         foreach my $p (keys(%{$loadfile{'global'}})) {
 776                 setprop($p, $loadfile{'global'}->{$p});
 777                 print STDERR "." if (!$verbose);
 778         }
 779
 780         my @users = usrlist();
 781         foreach my $usr (keys(%loadfile)) {
 782                 next if ($usr eq 'global');
 783                 if (!grep(/^${usr}$/, @users)) {
 784                         print STDERR "\nAdding user \"${usr}\".\n" if ($verbose);
 785                         usradd($usr);
 786                 }
 787                 foreach my $p (keys(%{$loadfile{$usr}})) {
 788                         setusrprop($usr, $p, $loadfile{$usr}->{$p});
 789                         print STDERR "." if (!$verbose);
 790                 }
 791         }
 792         print STDERR "done\n" if (!$verbose);
 793         print "Settings loaded, resetting board...\n";
 794         _cmd("boardreset");
 795         exit(0);
 796 }
 797
 798 if ($enable_debug ne '') {
 799         syslog_debug($enable_debug, "TRUE");
 800 }
 801
 802 if ($reset) {
 803         print "hardreset\n" if ($verbose);
 804         serveraction("hardreset");
 805 }
 806
 807 if ($powup) {
 808         powerup();
 809 }
 810
 811 if ($powdown) {
 812         powerdown();
 813 }
 814
 815 if ($powcyc) {
 816         powercycle();
 817 }
 818
 819 if ($showstat) {
 820         status();
 821 }
 822
 823 if ($resetrsbs2) {
 824         print "Resetting board...\n";
 825         _cmd("boardreset");
 826         exit(0);
 827 }
 828
 829 logout();